1. Manuals
  2. Brands
  3. Marksman Manuals
  4. Remote Starter
  5. M7a
  6. Installation manual

Marksman M7a Installation Manual

Hide thumbs Also See for M7a:
Table of Contents

Advertisement

Quick Links

Download this manual See also: User Manual
Installation
Manual
Model: M7a
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference; and
(2) This device must accept any interference received, including interference that may cause undesired operation.
Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to
this equipment. Such modifications could void the user's authority to operate the equipment.
For Technical Assistance, please call (800) 638-3600,
or visit www.magnadyne.com

Advertisement

Table of Contents
loading

Related Manuals for Marksman M7a

Summary of Contents for Marksman M7a

  • Page 1 Installation Manual Model: M7a This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference; and (2) This device must accept any interference received, including interference that may cause undesired operation.

  • Page 2: Installer Warnings

    Installer Warnings! This remote starter with alarm system is designed to be installed on fuel injected vehicles with an automatic transmission ONLY. • Never install this remote starter on a manual transmission vehicle. • This system must be installed and wired through a safety switch it will not start in any forward or reverse gear. •...
  • Page 3 Wiring Harness 1: White 6-Pin Heavy Gauge Connector The method that the remote starter uses to start the vehicle is a duplicate of the ignition switch function. Below, is an explanation of the 3 basic functions of the ignition switch. Since this installation will require analysis of the ignition switch functions, it is recommended making the three connections below at the ignition switch harness directly.
  • Page 4 Wiring Harness 1: White 6-Pin Heavy Gauge Wiring Connector (continued) Pink Wire: (Ignition 2 Output) Some vehicles have 2 ignition wires that must be powered. Connect the “Pink” wire to the ignition 2 wire from the ignition switch. No connection required on vehicles without second ignition. Brown Wire: (Accessory Output, Heater/AC Output) Connect the “Brown”...
  • Page 5 Wiring Harness 3: White 5-Pin Mini Connector Orange Wire : (-) 200mA Grounded Output when Armed This wire will become grounded when the alarm is armed. The current capacity of this wire is 200mA. This output can control a starter disable relay, when the system is triggered. The vehicle is prevented from any unauthorized starting, and also active when remote started.
  • Page 6 Wiring Harness 3: White 5-Pin Mini Connector (continued) Transponder Interfacing Using ALA984 Relay: (continued) Can also use optional RS-TIM bypass module. Ignition Switch Yellow Wire Transponder Key White 5-Pin Mini Connector +12 Volt Ignition GM VATS Key Override Using ALA984: Can also use RS-PLM bypass module. Passkey/Vats: Anti-Theft Bypass To Ignition Yellow Wire...
  • Page 7 Wiring Harness 3: White 5-Pin Mini Connector (continued) White Wire: (-) 200mA Programmable Output Dome Light Control Output +12 Volts or Ground Depending (Factory Default Setting): on Vehicle Requirement This wire becomes grounded Fuse when the dome light controls Courtesy circuit of the alarm is active.
  • Page 8 Wiring Harness 3: White 5-Pin Mini Connector (continued) Pink Wire: (continued) Start Status: (Shock Sensor Bypass Control) Output: (See Alarm Feature Stage 3 Programming) This wire is designed to bypass the shock sensor while remote start is operating. This wire will also supply an output for an additional 3 seconds after the remote start unit is turned off.
  • Page 9 Wiring Harness 4: 7-Pin Mini Black Connector (continued) White/Violet Wire: Positive Safety Shut Down Input This wire provides an instant shutdown for the remote start, whenever it receives +12 volts. If the brake lights switch in the vehicle switches +12 volts to the brake light circuit, connect this wire to the output side of the brake switch.
  • Page 10 Wiring Harness 4: 7-Pin Mini Black Connector (continued) White/Red Wire: (-) Tachometer Signal Connection This input provides the remote start system with information about the engine’s revolutions per minute (RPM). It can be connected to the negative side of the coil in vehicle with conventional coils. In multi-coil and high energy ignition system locating a proper signal may be more difficult.
  • Page 11 Wiring Harness 5: 3-Pin Mini Black Connector (continued) 5 Wire Ground at Rest Door Locking Systems Blue Wire Red Wire: Lock Green Wire Violet Wire To +12 Volts Black 3-Pin (Battery +) Mini Connector Black Wire: Unlock ALA-DL1 Relay Pack White Wire: Lock To Power Brown Wire: Unlock...
  • Page 12 Wiring Harness 5: 3-Pin Mini Black Connector (continued) Newly Installed Power Door Lock Motors Red Wire: Lock Blue Wire Violet Wire To +12 Volts Green Wire (Battery +) Black 3-Pin Connector Black Wire: Unlock White Wire Brown Wire To Ground ALA-DL1 Relay Pack To Newly...

  • Page 13: Enter The Programming Mode

    Wiring Harness 5: 3-Pin Mini Black Connector (continued) Unlock Driver's Door First Wiring for 3-Wire Positive Door Lock System White 5-Pin Blue Wire Mini Connector Green Wire Pink Wire Black 3-Pin Mini Connector To +12 Volts (Battery +) Driver's Door Motor Lock To Power Door Lock Switch...
  • Page 14 Alarm Feature Programming (Part 1) Examine the 3 different feature charts enclosed and decide which feature will get changed. Circling the feature to be changed will make the programming process much easier to perform. Step 1 Step 2 1X + 1X (Hold) Turn the ignition switch from the OFF position to the Before 15 seconds has passed, push and release the ON position 3 times leaving it in the OFF position the...
  • Page 15 Alarm Feature Programming (Part 2) Step 1 Step 2 3X + 1X (Hold) Before 15 seconds has passed, push and release the Turn the ignition switch from the OFF position to the valet switch 3 times then push the valet switch a fourth ON position 3 times leaving it in the OFF position the time and hold it down until 2 short chirps/beeps + 1 third time.
  • Page 16 Alarm Feature Programming (Part 3) Step 1 Step 2 5X + 1X (Hold) Turn the ignition switch from the OFF position to the Before 15 seconds has passed, push and release the valet switch 5 times then push the valet switch a sixth ON position 3 times leaving it in the OFF position the time and hold it down until 3 short chirp/beeps + 1 long third time.
  • Page 17 Remote Start Operation and Feature Programming Examine the two feature charts enclosed and decide which features to change. Circling the feature to be changed will make the programming process much easier to perform. Stage 1: Remote Start Feature Programming Step 1 Step 2 7X + 1X (Hold) Before 15 seconds has passed, push and release the valet...
  • Page 18 Remote Start Operation and Feature Programming Three Chirps, LED Three Pulses Button One Chirp, LED One Pulse Two Chirps, LED Two Pulses The vehicle has an aftermarket The vehicle has an aftermarket (Factory Default Setting) turbo timer installed. turbo timer installed. The alarm system can be armed the alarm system can be armed Turbo Timer Control...
  • Page 19 Remote Start Operation and Feature Programming Step 2 Step 1 9X + 1X (Hold) Turn the ignition switch from the OFF Before 15 seconds has passed, push and release the valet switch 9 times then push the valet switch a tenth time and hold it down until 5 position to the ON position 3 times leaving short chirps/beeps + 1 long chirp beep is heard then release it.
  • Page 20 Tachometer Detection Programming (continued) Step 4 Step 5 Step 6 START Start the vehicle’s engine with the Press and hold the valet switch. Turn off the ignition to stop the ignition key (while the engine is When the RPM level is learned, you engine.
  • Page 21 Voltage Detection Additional Programming If you have selected Voltage Detection, you may be required to program 1 additional feature as enclosed. Crank Detection Level Programming: Step 1 Step 2 Step 3 9X + 1X (Hold) Turn the ignition switch from the Before 15 seconds has passed, push Press the ( * - * ) button on the and release the valet switch 9 times...
  • Page 22 Fixed Crank Additional Programming If you have selected Elapsed Timer, you may be required to program 1 additional feature as enclosed. Step 1 Step 2 Step 3 9X + 1X (Hold) Turn the ignition switch from the Before 15 seconds has passed, push Press the ( * - * ) button on the and release the valet switch 9 times transmitter to start the vehicle.

  • Page 23: Returning To Factory Default Settings

    Returning to Factory Default Settings Step 1 Step 2 Step 3 11X + 1X (Hold) Before 15 seconds has passed, push Turn the ignition switch from the Press the (Lock) and (Car) button on and release the valet switch 11 times the transmitter together for 6 seconds, OFF position to the ON position 3 then push the valet switch a twelfth...

  • Page 24: Testing Your Installation

    Testing Your Installation Caution! The follow procedure must be performed after the installation of the Remote Start Device. It is the responsibility of the installing technician to complete these tests. Failure to test the unit in the following manner may result in personal injury, property damage, or both. 1.
  • Page 25 Testing Your Installation Optional Enable Switch Electronic Control Module (ECM) Solid State, Ignition Do Not Measure Resistance Black/White Wire Black 7-Pin Neutral Safety Switch Input Mini Connector Key-In Sensor Circuits: If the vehicle you ar working on does not have or you cannot locate the ECM reference wire, there are two alternatives available.
  • Page 26 Testing Your Installation Method 1 Key in Chime Module Driver's Door Pin Switch + 12 V Ignition Key In Sensor Switch Closes with Key In Ignition Cylinder White/Black Wire (-) Negative Safety Input Wire Safety Black 7-Pin To Hood Pin Switch Safety Shut Down Mini Connector IN4003 Key-In...
  • Page 27 Testing Your Installation Method 2 Ignition Key In Sensor Switch Closes with Key In Ignition Cylinder White/Black Wire (-) Negative Safety Input Wire Black 7-Pin Mini Connector Safety To Hood Pin Switch Safety Shut Down IN4003 Key-In To connect to the Sensor Circuit as shown for Method 2: A.

  • Page 28: Wiring Diagram

    Black/White Wire: (-) Neutral Safety Switch Input & (-) Remote Start Toggle Switch Important Note: Directly connect wire to "Ground" when this wire is not used. White/Red Wire: (+) Tachometer Input M7A-IM 6-22-06 Rev. C © Copyright 2004 Magnadyne Corporation...

Table of Contents