Table of Contents
Advertisement
The recorded title is stretched vertically.
16:9 aspect programmes are recorded in 4:3 aspect in the
following cases.
–
If you recorded or copied using "EP" or "FR
-R -R DL -RW(V)
(recordings 5 hours or longer)" recording mode.
– If you recorded or copied to a +R, +R DL or +RW.
– If you recorded in XP, SP, LP, EP, FR mode with "Aspect for
Recording" set to "4:3" in the Setup menu.
When you want to record 16:9 programme in the same
aspect, set "Rec for High Speed Copy" to "On", and set
"Aspect for Recording" to "16:9". (➡ 89, 90)
– By setting "Aspect for Recording" to "Automatic", there is a
chance that the recording will be made using the wrong
aspect. Match the aspect settings to the broadcast when
recording. (➡ 89)
It may be possible to adjust the display mode on the TV. Refer
to your television's operating instructions.
There is a lot of after-image when playing video.
Set "HD optimizer" in the Picture menu to "Off". (➡ 81)
When playing DVD-Video using progressive
output, one part of the picture momentarily
appears to be doubled up.
Set "Component Resolution" in the Setup menu to "576i/480i"
and "HDMI Video Mode" to "Off". This problem is caused by the
editing method or material used on DVD-Video, but should be
corrected if you use interlace output. (➡ 93)
There is no apparent change in picture quality
when adjusted with the Picture menu in the on-
screen menus.
The effect is less perceivable with some types of video.
The images from this unit do not appear on the
television.
Picture is distorted.
Make sure that the television is connected to VIDEO OUT
terminal, S VIDEO OUT terminal, COMPONENT VIDEO OUT
terminals or HDMI terminal on this unit. (➡ 16, 17, 99–101)
Make sure that the television's input setting is correct.
Progressive output is set to on but the connected television is
not progressive compatible. Press and hold [ g ] and [ q ](PLAY)
on the main unit at the same time for more than 5 seconds to
cancel this setting. The setting will change to interlace.
The unit's "TV System" setting differs from the TV system used
by the disc now playing. While stopped, keep pressing [ g ] and
[ ; OPEN/CLOSE] on the main unit for 5 or more seconds.
The system switches from PAL to NTSC or vice versa. (➡ 92)
When this unit is connected with an HDMI cable, use a disc
that matches with this unit's TV system.
Picture may not be seen when more than 4 devices are
connected with HDMI cables. Reduce the number of connected
devices.
The picture is distorted during play, or video will
not play correctly.
You may be playing a TV programme recorded with poor
reception or unfavorable weather conditions.
The picture may be distorted or a black screen may appear
briefl y between recorded titles in the following situations:
– between titles recorded with different recording modes.
– between scenes recorded with different aspect ratios.
– between scenes recorded with different resolutions.
– between playlist chapters.
Sound
No sound.
Low volume.
Distorted sound.
Cannot hear the desired audio type.
Check the connections and the "Digital Audio Output" settings.
Check the input mode on the amplifi er if you have connected
one. (➡ 16, 17, 90, 99–101)
Press [AUDIO] to select the audio. (➡ 39)
Turn "Sound Effects" in the Sound menu to "Off" in the following
cases.
– When using discs that do not have surround sound effects
such as Karaoke discs.
– When playing bilingual broadcast titles.
Audio may not be heard when more than 4 devices are
connected with HDMI cables. Reduce the number of connected
devices.
The sound effects will not work when the bitstream signal is
output from the HDMI AV OUT terminal or the DIGITAL AUDIO
OUT terminal.
To output audio from a device connected with an HDMI cable,
set "HDMI Audio Output" to "On" in the Setup menu. (➡ 92)
Depending on the connected equipment, the sound may be
distorted if this unit is connected with an HDMI cable.
When "BD-Video Secondary Audio" is set to "On", Dolby Digital
Plus and Dolby TrueHD are converted to 48 kHz Dolby Digital
and output or DTS-HD is converted to 48 kHz DTS and output.
In this case, set "BD-Video Secondary Audio" to "Off". (➡ 91)
Cannot switch audio.
You cannot switch the audio in the following cases.
– When the recording mode is XP and "Audio Mode for XP
Recording" is set to "LPCM". (➡ 91)
– When "Rec for High Speed Copy" is set to "On". (The default
setting is "On"). (➡ 90)
The amplifi er is connected using an optical digital cable, a
coaxial cable or an HDMI cable. You cannot switch the audio if
"Digital Audio Output" is set to "Bitstream". Set "Digital Audio
Output" to "PCM" or connect using audio cables. (➡ 90, 99)
There are discs for which audio cannot be changed because of
how the disc was created.
Operation
Cannot operate the television. The remote control
doesn't work.
Change the manufacturer code. Some televisions cannot be
operated even if you change the code. (➡ 95)
The remote control and main unit are using different codes.
Change the code on the remote control. (➡ 94)
Press and hold [OK] and the indicated
number button at the same time for
more than 5 seconds.
The batteries are depleted. Replace them with new ones. (➡ 3)
You are not pointing the remote control at the main unit's
remote control signal sensor during operation. (➡ 3)
Coloured glass may obstruct the signal reception/transmission.
Don't place the signal sensor in direct sunlight or in areas that
may be subject to sunlight exposure.
Software is updating when "UPD
unit's display. Wait until the update is completed. (➡ 98)
It may be necessary to set the code on the remote control
again after changing the batteries. (➡ 94)
It may be necessary to set the manufacturer code again after
changing the batteries. (➡ 95)
The child lock function is activated. (➡ 95)
/ " is displaying on the
RQT9428
109
Advertisement
Table of Contents
