Lightbulb Removal And Replacement; Troubleshooting Guide - Royal LEXON S17 Owner's Manual

LIGHTBULB REMOVAL AND REPLACEMENT

1.
WARNING: TO REDUCE THE RISK
OF ELECTRIC SHOCK- UNPLUG
CLEANER BEFORE CLEANING OR
SERVICING
NOTE: THIS CLEANER USES A COM-
MON AUTOMOTIVE LAMP #906, 13.0
VOLTS. FOR BULB REPLACEMENT CALL
1-800-321-1134 OR YOUR LOCAL AUTO
PARTS STORE.
TOOL REQUIRED:
PHILLIPS SCREWDRIVER
Diagram 1
1. Remove power nozzle from unit. Remove the five (5) screws.
2. To remove nozzle guard: turn
power nozzle over. Remove the
five (5) screws (Diagram 1).
3. Flip the power nozzle upright. Gently lift the cover off.
4. Pull bulb out of socket to remove. Do not twist. Push bulb into socket to replace.
5. Replace nozzle guard. Flip power nozzle over and replace the five (5) screws.
TROUBLE SHOOTING GUIDE
WARNING: TO REDUCE THE RISK OF PERSONAL INJURY- UNPLUG CLEANER BEFORE SERVICING
Problem Possible Cause
Cleaner won't run 1. Power cord not firmly plugged
into outlet
2. Cord not connected to cleaner
3. No voltage in wall plug
4. Blown fuse or tripped breaker
5. Needs service
6. Thermal protector shut
cleaner off due to high motor
temperatures.
Cleaner won't pick up 1. Dirt bag not installed correctly
or low suction
2. Dirt bag is full
3. Brushroll is worn
4. Broken or worn belt
5. Clogged filter
6. Nozzle/dirt passage hose is
clogged
7. Brushroll is turned off
Dust escaping from 1. Dirt bag is full
cleaner
2. Dirt bag not installed correctly
3. Hose not installed correctly
Cleaner tools won't 1. Hose clogged
pick up
2. Hose inlet clogged
3. Dirt bag full
4. Filter clogged
ANY OTHER SERVICING SHOULD BE DONE BY AN AUTHORIZED SERVICE REPRESENTATIVE
TO LOCATE A DEALER NEAR YOU, VISIT OUR WEBSITE AT www.royalvacuums.com OR CALL CUSTOMER
SERVICE AT (1-800-321-1134)
In the event that further assistance is required, see your Yellow Pages for an authorized Royal
tion to and from any place of repair are to be paid by the owner. The service parts used in this unit are easily replaced and read-
ily available from an authorized Royal Dealer or retailer. Always identify your cleaner by the model number and manufacturing
®
code when requesting information or ordering replacement parts. (The model number appears on the bottom of the cleaner.)
2.
Diagram 2
Pull bulb out of socket to remove.
Push new bulb into socket to
replace.
Possible Solution
1. Plug cord in firmly
2. Connect cord to cleaner- page 6
3. Check fuse or breaker in home
4. Replace fuse or reset breaker in home
5. Take to service center or call 1-800-321-1134
6. Review bottom of safety instructions- page 3
OR call 1-800-321-1134
1. Review dirt bag removal and replacement-
page 8
2. Replace dirt bag- page 8
3. Replace brushroll- page 10
4. Replace belt- page 10
5. Remove filter and clean- page 9
6. Remove nozzle base cover: remove obstruc-
tion OR remove hose: remove obstruction
7. Turn brushroll on- page 7
1. Review dirt bag removal and replacement-
page 8
2. Review dirt bag removal and replacement- page 8
3. Review hose installation- page 6
1. Remove hose and tools: Remove obstruction-
page 6
2. Remove hose and clean inlet
3. Replace the dirt bag- page 8
4. Replace filter- page 9
Dealer. Costs of any transporta-
®
11