ProForm G880 PFEVBE4805.0 User Manual page 9

USING THE OLYMPIC WEIGHT ADAPTERS
Press a 48mm Round Inner Cap (23) into the Olympic
Adapter (24). Attach the Olympic Adapter to the
Weight Tube (25) with a 1/4" x 9.5mm Allen Head Set
Screw (120). Make sure that the Set Screw is in
the bottom of the Adapter.
Olympic Adapter (24) can be attached to the Weight
Carriage (not shown) in the same manner.
Press a 48mm Round Inner Cap (23) into a Weight
Adapter (60). Attach the Weight Adapter to the Curl
Bar (76) with a 1/4" x 9.5mm Allen Head Set Screw
(120). Attach the other Weight Adapter to the Curl
Bar in the same manner.
To use some weights, Weight Tube Adapters (139)
will need to be slid onto the Weight Tube (25) or the
Carriage Adapters (not shown) will need to be slid
onto the Weight Carriage (not shown).
ADDING WEIGHTS TO THE LEG LEVER
To use the Leg Lever (4), slide the desired weights
(not included) onto the Weight Tube (25). Secure the
weights with a Weight Clip (58 or 77 [not shown]).
Weights can be added to the Curl Bar (not shown) in
the same manner. Secure the weights to the Curl Bar
with two Weight Clips (53 or 77 [not shown]).
WARNING:
Do not place more
than 68 kg (150 lbs.) on the Weight Tube (25) or
the Curl Bar. (76).
See the inset drawing. Weights can be stored on the
Storage Leg (45).
ATTACHING THE ACCESSORIES
To use the Lat Bar (57), attach it to the Lat Cable (81)
with a Cable Clip (122). For some exercises, the
Chain (78) should be attached between the Lat Bar
and the Lat Cable with two Cable Clips. Adjust the
length of the Chain between the Lat Bar and the
Cable so that the Lat Bar is in the correct starting
position for the exercise to be performed.
The Ankle Strap (not shown) can be attached to the
Low Cable (not shown) in the same manner.
25
24
139
23 120
60
76
23
120
4
Weight
25
Weight
58
81
122
78
122
57
20
12. See the inset drawing. Attach the Large Base
Cap (117) to the Rear Base (33) with an M4 x
16mm Screw (107) and an M8 x 16mm Screw
(98).
Attach the Rear Base (33) to the Center Base
(32) with two M10 x 78mm Bolts (110), two M10
Washers (99), and two M10 Nylon Locknuts (97).
Do not tighten the Locknuts yet.
Set the Center Base (32) inside of the Foot Plate
(48). Attach the Foot Plate to the Center Base
with two M10 x 68mm Bolts (113), two M10
Washers (99), and two M10 Nylon Locknuts (97).
Do not tighten the Locknuts yet.
13. Attach the Base Cap (47) to the Left Base (35)
with an M4 x 16mm Screw (107) and an M10 x
19mm Screw (118).
Hold the Storage Leg (45) so that the longer side
of the plate is oriented as shown. Attach the
Storage Leg to the Left Base (35) with two M10 x
92mm Carriage Bolts (111) and two M10 Nylon
Locknuts (97).
45
14. Attach the Left Base (35) to the Center Base (32)
with three M10 x 68mm Bolts (113), three M10
Washers (99), and two M10 Nylon Locknuts (97).
Do not tighten the Locknuts yet.
12
33
107
33
32
110
99
97
99
97
99
113
48
13
45
97
97
47
Longer
Side
118
107
35
111
14
32
97
99
97
35
99
9
117
98
110
113
113