Nylon Locknut (97). Do Not Overtighten The - ProForm G880 PFEVBE4805.0 User Manual

35. Locate the Lat Cable (81). Route the Cable up
through the Rear Top Frame (39) and over a
90mm Pulley (90). Attach the Pulley inside the
Rear Top Frame with an M10 x 78mm Bolt (110),
two M10 Washers (99), two 17mm Spacers (86),
and an M10 Nylon Locknut (97).
36. Route the Lat Cable (81) over a 90mm Pulley
(90) and down through the Rear Top Frame (39).
Attach the Pulley inside the Rear Top Frame with
an M10 x 78mm Bolt (110), two M10 Washers
(99), two 17mm Spacers (86), and an M10 Nylon
Locknut (97).
37. Wrap the Lat Cable (81) under a 90mm Pulley
(90). Attach the Pulley, a Small Cable Trap (125),
and two Half Finger Guards (133) to the indicated
hole in the two Pulley Plates (72) with an M10 x
47mm Bolt (136) and an M10 Nylon Locknut (97).
Make sure the Cable Trap is turned to hold the
Cable in the groove of the Pulley.
38. Wrap the Lat Cable (81) over a 90mm Pulley
(90). Attach the Pulley inside the Rear Top Frame
(39) with an M10 x 78mm Bolt (110) and an M10
Nylon Locknut (97).
39. Attach the Lat Cable (81) to the M10 x 19mm Hex
Head Bolt (132) in the Weight Carriage (71) with
an M10 Nylon Locknut (97). Do not overtighten
the Locknut; the Cable must be able to pivot.
35
90
39
81
97
99
86
86
99
110
36
97
90
86
81
39
99
86
99
37
81
97
125
133
133
72
90 136
72
38
39
97
110
90
81
39
81
71
97
132
16
25. Insert an M10 x 19mm Hex Head Bolt (132) into
the bracket on the Weight Carriage (71) from the
side shown.
Orient the Weight Carriage (71) as shown and
slide it onto the Rear Upright (38).
Attach the Weight Carriage Stop (70) to the Rear
Upright (38), at the indicated hole, with an M10 x
88mm Bolt (114) and an M10 Nylon Locknut (97).
Make sure the Square Carriage Bushing (61)
is on the bottom.
26. Attach the Rear Top Frame (39) to the Rear
Upright (38) with two M10 x 72mm Hex Head
Bolts (130), two M10 Washers (99), and two M10
Nylon Locknuts (97). Make sure the bolt heads
are set inside the hex holes in the Rear
110
Upright. Do not tighten the Locknuts yet.
27. Attach the Rear Top Frame (39) to the Center
Upright (37) with two M10 x 78mm Bolts (110),
two M10 Washers (99), and two M10 Nylon
Locknuts (97). Do not tighten the Locknuts yet.
Attach the Rear Top Frame (39) to the Top Frame
(40) with two M10 x 127mm Bolts (126), four M10
Washers (99), and two M10 Nylon Locknuts (97).
Do not tighten the Locknuts yet.
25
97 70
114
61
132
71
Hole
38
26
39
130
27
110
99
126
40
99
99
97
39
97
37
99
97
13
97
99
99
38