Advertisement
Quick Links
Download this manual
See also:
Installation Manual
TruVision IP PTZ Camera FW5.1 Installation
Guide
Introduction
This installation guide provides basic information on setting up
and using the camera. Detailed information on the cameras
can be found in the configuration manual.
Product overview
This is the installation guide for following TruVision IP PTZ
camera models:
TVP-1101
(1.3 MPX pendant, 20X, PAL)
TVP-3101
(1.3 MPX pendant, 20X, NTSC)
TVP-1102
(1.3 MPX surface, 20X, PAL)
TVP-3102
(1.3 MPX surface, 20X, NTSC)
TVP-1103
(1.3 MPX flush, 20X, PAL)
TVP-3103
(1.3 MPX flush, 20X, NTSC)
TVP-1104
(2 MPX pendant, 20X, PAL)
TVP-3104
(2 MPX pendant, 20X, NTSC)
TVP-1105
(2 MPX surface, 20X, PAL)
TVP-3105
(2 MPX surface, 20X, NTSC)
TVP-1106
(2 MPX flush, 20X, PAL)
TVP-3106
(2 MPX flush, 20X, NTSC)
TVP-1107
(2 MPX pendant, 30X, PAL)
TVP-3107
(2 MPX pendant, 30X, NTSC)
TVP-1122
(2 MPX pendant, 30X, IR, PAL)
TVP-3122
(2 MPX pendant, 30X, IR, NTSC)
Before you begin
Unpack everything. Check the items for damage, and verify
that all items are included. The camera is shipped with the
following items:
Dome camera
Installation Guide
CD with the Configuration Manual and Device Manager
© 2015 United Technologies Corporation. All rights reserved.
Interlogix is part of UTC Building & Industrial Systems, a unit of United Technologies Corporation. All rights reserved.
Installation environment
When installing your camera, consider these factors:
•
Place the camera in a secure location.
•
Ensure that the camera is in a well-ventilated area.
•
Do not expose the camera to rain or moisture.
Caution: Risk of explosion if the battery is replaced by an
incorrect type. Dispose of used batteries according to the
instructions.
Camera description
Figure 1: Overview of the dome camera (pendant-mount shown)
TVP-1122/3122 cameras only:
1.
Power supply cord
Connect 24 VAC power supply
2.
Video output
Connect the BNC connector to a
CCTV monitor
3.
Ethernet RJ45 connector. Connect
to the network devices
Connect to the PoE+ switch
P/N 1073029-EN • REV A • ISS 03JUN15
4.
Alarm input/outputs and
audio in/out port
5.
Housing
6.
Bubble
7.
Metal housing
8.
IR LEDs
9.
Camera
Advertisement
Related Manuals for Interlogix FW5.1
Summary of Contents for Interlogix FW5.1
-
Page 1: Installation Environment
Connect to the PoE+ switch Camera © 2015 United Technologies Corporation. All rights reserved. P/N 1073029-EN • REV A • ISS 03JUN15 Interlogix is part of UTC Building & Industrial Systems, a unit of United Technologies Corporation. All rights reserved. -
Page 2: Installing A Camera
Connections Installing a camera There are seven built-in alarm inputs to use as internal alarm triggers and two alarm built-in outputs in the camera housing. Pendant-mount camera These connections do not apply to the TVP-1122/3122 Prepare the mounting surface and install the camera cameras. -
Page 3: Flush-Mount Camera
Unscrew the bubble from the camera and remove the protective tape from the PTZ module. Press the two tabs on either side of the PTZ module and remove it from the camera housing. Route the cables from the bracket and connect them to Caution: The RS-232 serial port on the camera is not a the PCB of the module through the cable entry hole on the network connection. -
Page 4: Accessing The Camera Over The Internet
Using the camera with TruVision Navigator Install the housing onto the mounting base. Line up the A camera must be connected to an Interlogix NVR or hybrid direction of the arrow on the housing with the spring end of DVR to be operated by TruVision Navigator. Please refer to the the mounting base. -
Page 5: Specifications
Specifications Change the administrator password once the set-up is complete. Only authorized users should be able to modify camera settings. Electrical Voltage input 24 VAC, PoE+ (IEEE 802.3at) To access the camera online: Power Pendant housing: In the web browser enter the camera’s IP address (default consumption PoE: Max. -
Page 6: Regulatory Information
© 2015 United Technologies Corporation. Copyright digital device, pursuant to part 15 of the FCC Interlogix is part of UTC Building & Industrial Rules. These limits are designed to provide Systems, a unit of United Technologies reasonable protection against harmful Corporation.