Wshp Open Test Mode; Retry Mode; Aquazone Deluxe D Control Led Indicators - Carrier PTV Installation, Start-Up And Service Instructions Manual

WSHP Open Test Mode -- To
enter WSHP Open test
mode, navigate from the BACview 6 home screen to the config-
uration screen. Choose the service screen and enable unit test.
The controller will then test the following:
FAN TEST -- Tests all fan speeds, sequences fan from low to
high, and operates each speed for one minute. Resets to disable
on completion.
COMPRESSOR TEST--Tests compressor cooling and
heating operation. Sequences cooling stage 1 then cooling
stage 2 followed by heating stage 2 then reduces capacity to
heating stage 1. Operates for 1 minute per step.
DEHUMIDIFICATION TEST -- Tests dehumidification
mode. Operates for 2 minutes.
AUXILIARY HEATING TEST -- Tests auxiliary heat.
Sequences fan on and enables heating coil for 1 minute.
H20 ECONOMIZER TEST -- Tests entering/returning
water loop economizer operation. Sequences fan and opens
economizer water valve for one minute.
OPEN VENT DAMPER 100% TEST -- Tests outside air
(OA) damper operation.
PREPOSITION OA DAMPER -- Prepositions OA damper
actuator to set proper preload.
NOTE: The auxiliary heating test, H20 economizer test, open
vent damper 100% test, and preposition OA damper features
will not be visible on the screen unless configured.
Once tests are complete, set unit test back to disable. Unit will
automatically reset to disable after 1 hour.
Retry Mode
--
In Retry mode, the status LED will start to
flash slowly to signal that the control is trying to recover from
an input fault. The control will stage off the outputs and try to
again satisfy the thermostat used to terminal Y. Once the ther-
mostat input calls are satisfied, the control will continue normal
operation.
NOTE: If 3 consecutive faults occur without satisfying the
thermostat input call to terminal Y, the control will go into
lockout mode. The last fault causing the lockout is stored in
memory and can be viewed by entering Test mode.
Aquazone
TM
Deluxe D Control LED Indica-
tors
-- There are 3 LED indicators on the Deluxe D control:
STATUS LED- Status LED indicates the current status or
mode of the D control. The Status LED light is green.
TEST LED- Test LED will be activated any time the D
control is in test mode. The Test LED light is yellow.
FAULT LED -- Fault LED light is red. The fault LED will
always flash a code representing the last fault in memory. If
there is no fault in memory, the fault LED will flash code 1 and
appear as one fast flash alternating with a 10-second pause.
See Table 29.
Table 29 -- Ac uazone Deluxe D Control Current LED Status and Alarm Relay Operations
STATUS LED TEST LED
DESCRIPTION (Green) (Yellow) FAULT LED (Red) ALARM RELAY
Normal Mode On Off Flash Last Fault Code in Memory Open
Cycle (closed 5 sec,
Normal Mode with PM On Off Flashing Code 8 open 25 sec .... )
Deluxe D Control Off Off Off Open
is non-functional
Test Mode -- On Flash Last Fault Code in Memory Cycling Appropriate Code
Night Setback Flashing Code 2 -- Flash Last Fault Code in Memory --
ESD Flashing Code 3 -- Flash Last Fault Code in Memory --
Invalid T-stat Inputs Flashing Code 4 -- Flash Last Fault Code in Memory --
No Fault in Memory On Off Flashing Code 1 Open
HP Fault Slow Flash Off Flashing Code 2 Open
LP Fault Slow Flash Off Flashing Code 3 Open
FP1 Fault Slow Flash Off Flashing Code 4 Open
FP2 Fault Slow Flash Off Flashing Code 5 Open
CO Fault Slow Flash Off Flashing Code 6 Open
Over/Under Voltage Slow Flash Off Flashing Code 7 Open (closed after 15 minutes)
HP Lockout Fast Flash Off Flashing Code 2 Closed
LP Lockout Fast Flash Off Flashing Code 3 Closed
FP1 Lockout Fast Flash Off Flashing Code 4 Closed
FP2 Lockout Fast Flash Off Flashing Code 5 Closed
CO Lockout Fast Flash Off Flashing Code 6 Closed
LEGEND
CO -- Condensate Overflow HP -- High Pressure
ESD -- Emergency Shutdown LP -- Low Pressure
FP -- Freeze Protection PM -- Performance Monitor
NOTES:
1, If there is no fault in memory, the Fault LED will flash code 1,
2, Codes will be displayed with a 10-second Fault LED pause,
3, Slow flash is 1 flash every 2 seconds,
4, Fast flash is 2 flashes every 1 second,
5, EXAMPLE: "Flashing Code 2" is represented by 2 fast flashes
followed by a 10-second pause, This sequence will repeat con-
tinually until the fault is cleared,
44