Step 8 -- Wire Field Power Supply - Carrier PTV Installation, Start-Up And Service Instructions Manual

Table 2 -- Water Quality Guidelines
I HX CLOSED RECIRCULATINGt" OPEN LOOP AND RECIRCULATING WELL**
CONDITION MATERIAL*
Scaling Potential -- Primary Measurement
Above the given limits, scaling is likely to occur. Scaling indexes should be calculated using the limits below.
Hardness Method All N/A pH < 7.5 and Ca Hardness, <100 ppm
Index Limits for Probable Scaling Situations (Operation outside these limits is not recommended.)
Scaling indexes should be calculated at 150 F for direct use and HWG applications, and at 90 F for indirect HX use. A monitoring plan should be
implemented.
6.0 - 7.5
Ryznar Stability Index All N/A if >7.5 minimize steel pipe use.
Langelier Saturation Index -0.5 to +0.5
All N/A If <-0.5 minimize steel pipe use.
Based upon 150 F HWG and direct well, 85 F indirect well HX.
Iron Fouling
Iron Fe 2+ (Ferrous) <0.2 ppm (Ferrous)
(Bacterial Iron Potential) All N/A
If Fe2+ (ferrous) >0.2 ppm with pH 6 - 8, 02<5 ppm check for iron bacteria.
Iron Fouling All N/A <0.5 ppm of Oxygen
Above this level deposition will occur.
Corrosion Preventionll
6 - 8.5 6 - 8.5
pH All Monitor/treat as needed. Minimize steel pipe below 7 and no open tanks with pH <8.
Hydrogen Sulfide (H2S) <0.5 ppm
All N/A At H2S>0.2 ppm, avoid use of copper and cupronickel piping or HXs.
Rotten egg smell appears at 0.5 ppm level.
Copper alloy (bronze or brass) cast components are okay to <0.5 ppm.
Ammonia ion as Hydroxide, <0.5 ppm
Chloride, Nitrate and Sulfate All N/A
Compounds
Maximum Chloride Levels
Copper
Cupronickel
304 SS
316 SS
Titanium
N/A
N/A
N/A
N/A
N/A
Maximum allowable at maximum water temperature.
5O F (10 C) 75 F (24 C) 100 F (38 C)
<20 ppm NR NR
<150 ppm NR NR
<400 ppm <250 ppm <150 ppm
<1000 ppm <550 ppm <375 ppm
>1000 ppm >550 ppm >375 ppm
Erosion and Clogging
Particulate Size and Erosion <10 ppm of particles and a <10 ppm (<1 ppm "sandfree" for reinjection) of particles and a maximum velocity
All maximum velocity of 6 fps. of 6 fps. Filtered for maximum 800 micron size. Any particulate that is not
Filtered for maximum removed can potentially clog components.
800 micron size.
Brackish Use cupronickel heat exchanger when concentrations of calcium or sodium chic-
All N/A ride are greater than 125 ppm are present. (Seawater is approximately 25,000
ppm.)
LEGEND
HWG -- Hot Water Generator
HX -- Heat Exchanger
N/A -- Design Limits Not Applicable Considering Recirculating
Potable Water
NR -- Application Not Recommended
SS -- Stainless Steel
*Heat exchanger materials considered are copper, cupronickel, 304 SS
(stainless steel), 316 SS, titanium.
tCIosed recirculating system is identified by a closed pressurized piping
system.
**Recirculating open wells should observe the open recirculating design
considerations.
ttlf the concentration of these corrosives exceeds the maximum allowable
level, then the potential for serious corrosion problems exists.
Sulfides in the water quickly oxidize when exposed to air, requiring that no
agitation occur as the sample is taken. Unless tested immediately at the
site, the sample will require stabilization with a few drops of one Molar zinc
acetate solution, allowing accurate sulfide determination up to 24 hours
after sampling. A low pH and high alkalinity cause system problems, even
when both values are within ranges shown. The term pH refers to the acid-
ity, basicity, or neutrality of the water supply. Below 7.0, the water is consid-
ered to be acidic. Above 7.0, water is considered to be basic. Neutral water
contains a pH of 7.0.
To convert ppm to grains per gallon, divide by 17. Hardness in mg/I is
equivalent to ppm.
Table 3 -- Metal Hose Minimum Bend Radii
HOSE DIAMETER (in.) MINIMUM BEND RADII (in.)
1/2 21/2
3/4 4
1 51/2
Swivel
Brass \ Brass
.... _., .................................................................... Rib Crimped_tting \ .... Fit}ing
I (2 ft LeLgth Standard) 4
MPT
Fig. 14 -- Supply/Return Hose Kit
Step 8 E Wire Field Power Supply
To avoid possible injury or death due to electrical shock,
open the power supply disconnect switch and secure it in
an open position during installation.
Use only copper conductors for field-installed electrical
wiring. Unit terminals are not designed to accept other
types of conductors.
All field-installed wiring, including the electrical ground,
MUST comply with the National Electrical Code (NEC) as
well as applicable local codes. In addition, all field wiring must
12