Setup Menu - Onkyo TX-NR900E Instruction Manual

Setup Menu

When making the various settings required to configure your TX-NR900/900E for optimum performance, you can either use the OSD Menu
that appears on your television monitor or you can use the display on the front of the TX-NR900/900E. The OSD Menu is a settings menu that
is displayed on your TV monitor. For your reference when performing the setting procedures, this manual shows both the OSD Menu displayed
on your television monitor and the display on the front of the TX-NR900/900E.
The Setup Menu consists of the Basic Menu that is divided up into 4 menus, the Hardware Setup Menu, Speaker Setup Menu, Input Setup Menu,
and Audio Adjust Menu, and the Advanced Menu that contains the menus of the Basic Menu, the Preference Menu, and Network Setup Menu.
These menus are then divided up into various sub-menus, and these contain settings for you to optimize your home theater as you wish.
The display shown below is an example. The actual contents of your display may differ depending on the model of your region and the selected
input source.
Basic Menu
Your TX-NR900/900E is provided
with a Basic Menu for those who are
not familiar with many of the
advanced settings of an AV receiver
or those who wish to watch movies
and listen to music with the minimal
amount of setup. With the Basic
Menu, the settings that rarely need to
be set or that are only needed for
advanced fine-tuning of the sound
quality are not displayed.
Basic Menu
0.Hardware Setup
1.Speaker Setup
2.Input Setup
3.Audio Adjust
→Advanced Menu
|ENTER|Quit:|SETUP|
Note:
The Hardware Setup Menu is accessible from the
Basic Menu at an initial setting. After brought up
on the screen and set any of its items, the menu is
no longer available from the Basic Menu.
In this case, you can gain access to the menu via
the Advanced Menu.
Advanced Menu
The Advanced Menu provides features such as the Listening Mode Presets that allow
you to customize the output sound for movies and music just the way you like and the
AV Sync Setup that allows you to adjust for discrepancies between the video and audio
timing. Settings listed with
using the Advanced Menu.
Advanced Menu
0.Hardware Setup
1.Speaker Setup
2.Input Setup
3.Audio Adjust
4.Preference
5.Network Setup
→Basic Menu
|ENTER|Quit:|SETUP|
44
0.Hardware Setup
1.Speaker Impedance
2.Surr Back/Zone2
3.IR IN Setup
4.AM Frequency Step
|ENTER|Quit:|SETUP|
1.Speaker Setup
1.Speaker Config
2.Speaker Distance
3.Level Calibration
|ENTER|Quit:|SETUP|
2.Input Setup
Input:DVD
1.Digital Setup
2.Multichannel Setup
3.Video Setup
4.Character Input
5.IntelliVolume
|ENTER|Quit:|SETUP|
3.Audio Adjust
1.Tone Control
2.Surround Speakers
3.Sound Effect
|ENTER|Quit:|SETUP|
next to their name are settings that can be set
Refer to the TX-NR900/900E
"How to use Net-Audio"
instruction manual, a
separate volume, for
description of the network-
related settings.
→default
5.Network Setup
1.IP Address
2.Proxy Setup
3.MAC Address
4.Client
5.Update Utility
|ENTER|Quit:|SETUP|
0.Hardware Setup
1.Speaker Impedance
2.Surr Back/Zone2
3.IR IN Setup
4.AM Frequency Step
|ENTER|Quit:|SETUP|
1.Speaker Setup
1.Speaker Config
2.Speaker Distance
3.Level Calibration
|ENTER|Quit:|SETUP|
2.Input Setup
Input:DVD
1.Digital Setup
2.Multichannel Setup
3.Video Setup
4.Character Input
5.IntelliVolume
6.Listening Mode Preset
|ENTER|Quit:|SETUP|
3.Audio Adjust
1.Tone Control
2.Surround Speakers
3.Sound Effect
4.Delay
5.LFE Level
6.Mono
7.Theater-Dimensional
8.Surround
3.Audio Adjust
9.THX
10.Mono Movie
11.Enhanced 7
12.Orchestra
13.Unplugged
14.Studio-Mix
15.TV Logic
→default
4.Preference 4.Preference
1.Volume Setup 1.Volume Setup
2.Headphone Level Setup 2.Headphones Level
3.OSD Setup 3.OSD Setup
4.OSD Position
4.OSD Position
|ENTER|Quit:|SETUP| Quit:|SETUP|