Onkyo TX-NR900E Instruction Manual page 19

Connecting to Audio/Video equipment
: Signal flow
S Video input
Video input
L (white)
Analog audio
input
R (red)
6. VCR (VIDEO 1)
R (red)
Analog audio
output
L (white)
Video output
S Video output
5. Connecting a television monitor or projector (MONITOR
OUT)
The TX-NR900/900E is equipped with a simple Y/C separate circuit
and simple Y/C mixed circuit. Since both the signal from the S
VIDEO and VIDEO inputs are output to the MONITOR OUT S
VIDEO output, if the television or projector is equipped with an S
video input, it is unnecessary to connect the video connectors. If it is
equipped with only a video input, connect it to the MONITOR OUT
VIDEO output.
Using an RCA video cable, connect the video input jack (composite)
of the device to the MONITOR OUT VIDEO jack of the TX-
NR900/900E. Or if the device has an S video input jack, connect it to
the MONITOR OUT S VIDEO jack of the TX-NR900/900E using
an S video cable. Or if the device has component video inputs,
connect them to the bank of COMPONENT VIDEO OUTPUT jacks
on the TX-NR900/900E.
Note that the OSD Menu data will be output to the MONITOR OUT
VIDEO and S VIDEO jacks, and will not output to the
COMPONENT VIDEO OUTPUT jack.
DIGITAL PRE
AUDIO VIDEO
INPUT
NNA R
COAX FRONT
1
R L
SUB
AM
2 OUT
SURR
3 IN
SURR
R
BACK/
OPT
ZONE 2
FM
1 OUT
75
FRONT
2 IN
O
R
L
SUB
3 PHONO OUT
SURR
4
CD IN
R
OUT
OPT
1 IN
SURR
BACK
TAPE
2 IN
IN
GND
L R L
AUDIO VIDEO
DIGITAL O
OUTPUT
6. Connecting a video cassette recorder (VIDEO 1)
Using RCA video cables, connect the video output jack (composite)
of the video cassette recorder to the VIDEO 1 VIDEO IN jack of the
TX-NR900/900E and connect the video input jack of the video
cassette recorder to the VIDEO 1 VIDEO OUT jack of the TX-
NR900/900E. Or if the video cassette recorder has S video input and
output jacks, connect them to the VIDEO 1 S VIDEO IN and OUT
jacks of the TX-NR900/900E using S video cables. Or if the video
cassette recorder has component video outputs, connect them to one
of the banks of COMPONENT VIDEO INPUT jacks on the TX-
NR900/900E.
With the initial settings of the TX-NR900/900E, the VIDEO 1
input source is set for the COMPONENT VIDEO INPUT 2
jacks.
If you connect the video cassette recorder to the COMPONENT
VIDEO INPUT 1 jacks, this must be changed at Setup Menu →
Input Setup → Video Setup → Component Video (see page 53).
Using RCA audio cable, connect the audio output jacks of the video
cassette recorder to the VIDEO 1 AUDIO IN jacks of the TX-
NR900/900E and connect the audio input jacks of the video cassette
recorder to the VIDEO 1 AUDIO OUT jacks of the TX-NR900/
900E. Make sure that you properly connect the left channels to the L
jacks and the right channels to the R jacks.
If you are connecting a digital output device to the VIDEO 1 jack
instead of a VCR, connect it to either the DIGITAL INPUT COAX
jack or DIGITAL INPUT OPT jack depending on the type of
connector on the device.
With the initial settings of the TX-NR900/900E, the VIDEO 1
input source is set for digital input at the COAX 2 jack.
If the digital connection is made at a different jack, this must be
changed at Setup Menu → Input Setup → Digital Setup (see page
51).
Video input
S Video input
COMPONENT
S VIDEO
VIDEO
OUTPUT
MONITOR
OUT
Y
ZONE 2 P
B
DVD
P
R
INPUT 1
Y
VIDEO 1
P
B
P
R
VIDEO 2
INPUT 2
Y
VIDEO 3 P
B
VIDEO 4 P
R
S VIDEO
5. TV monitor or projector
(MONITOR OUT)
Y
P
B Component video input
P
R
19