Saeco D.A. 5P Instruction And Maintenance Manual page 46

English
7.4 Selection of the parameter to be
changed or displayed
The five menu items can be scrolled on the display to verify their
parameters and eventually modify them.
This requires:
- Entering function programming (refer to "7.3 Programming
Mode Access")
- Scroll menu items with the "UP" and "DOWN" keys.
- Stop the selection on the menu item managing the function to
be verified or modified.
- Press the "ENTER" key to enter in the item.
- Scroll the various functions with the "UP" and "DOWN" keys.
- Stop the selection on the function whose parameters should be
displayed or modified.
- Press the "ENTER" key to display the parameter.
7.5 Changing and saving parameters
Changing or memory-storing parameters requires:
- Displaying the parameter to be changed (refer to "7.4 Selec-
tion of the parameters to be changed or modified").
- Pressing the "ENTER" key to access the parameter to be mod-
ified. The flashing cursor places itself on a digit.
- Increasing or decreasing the digit value by means of the "UP"
and "DOWN" keys.
Pressing the ENTER" key the displayed digit is stored to mem-
ory and replaces the previous one, while at the same time the
cursor moves to the next digit.
- Following the same procedure to set the remaining digits.
- After having completed the digit change, confirm the new pa-
rameter with the "ENTER" key.
If the change is accepted the flashing cursor disappears.
Sometimes the parameter to be stored to memory must be chosen
among a list of pre-set parameters ("YES" and "NO", "WEEKDAYS"
(weekdays), etc...). In these cases the "UP" and "DOWN" keys
are used to scroll the flashing cursor or visualize the possible choic-
es on the display.
Example
Setting "YES" or "NO" in a function requires:
- Selecting the function.
- Accessing the change level by means of the "ENTER" key.
Upon access a selection signal appears on one of the two
writings: "Y" (YES) or "N" (NO).
- Using the "UP" or "DOWN" keys to select "Y" (YES) or "N"
(NO).
- Pressing "ENTER" to confirm the choice. Pressing "ENTER" au-
tomatically moves to the access level of the function.
Inserting text in a function requires:
- Selecting the function.
- Pressing "ENTER" to type the text.
The flashing cursor appears under the first letter on the left.
- Using the "UP" or "DOWN" keys to scroll the letters.
- Pressing "ENTER" to confirm the letter.
The cursor moves to the following letter.
14
Operate in the same way for all the letters to be entered.
The maximum number of letters that can be inserted is 16.
Once the insertion is completed press "ENTER" twice.
If you want to move to a further parameter press the "UP" or
"DOWN" keys.
• In model D.A. 5P to exit the modified parameter and change
level, press the "D - Cancel" key.
Once all the parameters have been changed and stored to mem-
ory, press the "D - Cancel" key for as many times until you reach
the function allowing exit from Programming "EXIT PROGRAM
Y/N".
• In the model D.A. 3P to exit the modified parameter or change
level, press the "UP" or "DOWN" keys.
Once all the parameters have been changed and stored to mem-
ory, press the "UP" o "DOWN" keys for as many times until you
reach the function allowing exit from Programming "EXIT PRO-
GRAM Y/N".
7.6 Menu description
N.B.: The numbers to be entered for each item are not referred
to a measure unit (gr., ml., etc.), and are mere reference
values.
Important
The following description of the menus refers to model D.A.
5P, but it may be referred also to model D.A. 3P without sub-
stantial differences.
First main voice
of the programming menu
S Y S T E M M A N A G E M E N T S Y S T E M M A N A G E M E N T S Y S T E M M A N A G E M E N T
S Y S T E M M A N A G E M E N T S Y S T E M M A N A G E M E N T
Press "ENTER" to enter item functions.
V M C O D E V M C O D E V M C O D E
V M C O D E V M C O D E
0 0 1 0 0 7 0 0 1 0 0 7 0 0 1 0 0 7 0 0 1 0 0 7 0 0 1 0 0 7
This function allows the assignment of an identification code to
each device.
To insert the code you should follow the procedure described in
chapter "7.5 Changing and saving parameters".
C O U N T E R S C O U N T E R S
C O U N T E R S C O U N T E R S C O U N T E R S
This function allows the control of the number of drink, soluble
products and water vends.
Pressing "ENTER" gives access to the lower level where counters
are listed.
The lower line of each single counter displays the total vends after
the letters "T" and "P".