Samsung SNV-L6013R User Manual page 37

QoS
You can specify the priority to secure a stable transfer rate for a specific IP.
1. From the Setup menu, select the <network (
2. Click <QoS>.
3. Click the [Add ( )] button.
The IP list will be created.
4. Enter an IP address to which you will apply QoS.
The default prefix for IPv4 is 32;
`
M
For DSCP, the default is set to 63.
Only the IP addresses that are set to <Use> can be prioritized.
`
5. Select an IP to delete from the list.
Click the [Delete ( )] button.
6. When done, click [Apply ( )].
Snmp
With the SNMP protocols, the system or network admin can monitor the network devices on a remote site,
and configure the environment settings.
1. From the Setup menu, select the <network (
2. Click <Snmp>.
3. Specify the <Snmp>.
• Enable SNMP v1 : SNMP version 1 will be active.
• Enable SNMP v2c : SNMP version 2 will be active.
- Read community : Provide the name of the read
community where you can access to the SNMP
information.
The default name is <public>.
- Write community : Provide the name of the write
community where you can access to the SNMP
information. The default name is <write>.
• Enable SNMP Trap : SNMP trap is used to send important events and conditions to the Admin.
- Community : Enter the trap community name to receive messages.
- IP address : Enter the IP address to which messages will be sent.
- Authentication failure : It specifies whether an event shall be generated when the community
information is invalid.
- Network connection : It specifies whether an event shall be generated when the network
disconnection is restored.
)> tab.
)> tab.
• Enable SNMP v3 : SNMP version 3 will be active.
- Password : Specify the default password for SNMP version 3. The default password is
<admin4321>.
The default password can be exposed to a hacking thread so it is recommended to change the password after installing the
`
product.
Note that the security and other related issues caused by the unchanged password shall be responsible for the user.
Password should be longer than 8 characters, no more than 16 characters.
`
4. When done, click [Apply ( )].
SNMP v3 is only able to be set when the secure connection mode is HTTPS.
`
J
Refer to "SSL". (page 36)
If you don't use SNMP v3, there may be a security issue.
`
Auto ip configure
You can set the IP available for access and camera searching automatically.
1. From the Setup menu, select the <network (
2. Click <Auto ip configure>.
3. Set the <Link-Local ipv4 address>.
An additional IP address may be assigned to assess the
camera from the Link-Local network.
• Auto configure : It specifies Able or Disable for the Link-
Local IPv4 address.
• IP address : Display the assigned IP address.
• Subnet mask : Display the subnet mask of the assigned IP.
4. Set the <upnp discovery>.
Cameras can be automatically searched in the client and
operating system in support of the UPnP protocol.
• UPnP discovery : It specifies Able or Disable for UPnP Discovery.
• Friendly name : Display the camera name.
Friendly name is displayed in the format of SAMSUNG-<Model Name>-<MAC Address>.
In the Windows operating system which basically supports UPnP, the cameras connected to the network are displayed.
`
M
5. Set the <Bonjour>.
Cameras can be automatically searched in the client and operating system in support of the Bonjour
protocol.
• Bonjour : It specifies Able or Disable for Bonjour.
• Friendly name : Display the camera name.
Friendly name is displayed in the format of SAMSUNG-<Model Name>-<MAC Address>.
In the Mac operating system, which support Bonjour by default, the connected cameras are automatically displayed in the
`
M
Bonjour bookmark of the Safari web browser.
If the Bonjour bookmark is not displayed, check Bookmarks Setup in the "Preference" menu.
6. When done, click [Apply ( )].
)> tab.
English _37