Samsung SND-L5083R User Manual
  1. Manuals
  2. Brands
  3. Samsung Manuals
  4. Security Camera
  5. SND-L5083R
  6. User manual

Samsung SND-L5083R User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

NETWORK CAMERA

SND-L5013/SND-L5083R/
User Manual
SNO-L5083R/SNV-L5083R

Advertisement

Table of Contents
loading

Related Manuals for Samsung SND-L5083R

Summary of Contents for Samsung SND-L5083R

  • Page 1: Network Camera

    NETWORK CAMERA SND-L5013/SND-L5083R/ User Manual SNO-L5083R/SNV-L5083R...
  • Page 2 Disclaimer Samsung Techwin makes the best to verify the integrity and correctness of the contents in this document, but no formal guarantee shall be provided. Use of this document and the subsequent results shall be entirely on the user’s own responsibility.

  • Page 3: Important Safety Instructions

    overview important Safety inStructionS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings, Install in accordance with the manufacturer’s instructions.

  • Page 4: Explanation Of Graphical Symbols

    overview warninG TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. DO NOT INSERT ANY METALLIC OBJECT THROUGH THE VENTILATION GRILLS OR OTHER OPENNINGS ON THE EQUIPMENT. Apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.
  • Page 5 Battery Batteries(battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like. Disconnection Device Disconnect the main plug from the apparatus, if it’s defected. And please call a repair man in your location. when used outside of the u.S., it may be used Har code with fittings of an approved agency is employed.
  • Page 6 overview Please read the following recommended safety precautions carefully. y Do not place this apparatus on an uneven surface. y Do not install on a surface where it is exposed to direct sunlight, near heating equipment or heavy cold area. y Do not place this apparatus near conductive material.

  • Page 7: Table Of Contents

    Product Features Recommended PC Specifications Recommended Micro SD/SDHC Memory Card Specifications NAS recommended specs What’s Included At a Glance (SND-L5013) At a Glance (SND-L5083R) At a Glance (SNO-L5083R) At a Glance (SNV-L5083R) iNSTALLATioN & Installation (SND-L5013/ CoNNeCTioN SND-L5083R) Installation (SNO-L5083R)

  • Page 8: Web Viewer

    overview web vieweR Connecting to the Camera Password setting Login Installing STW WebViewer Plugin Using the Live Screen Playing the recorded video SeTup SCReeN Setup Basic Setup Video & Audio setup Network Setup Event Setup NAS (Network Attached Storage) guide System Setup Viewing profile information AppeNDix...

  • Page 9: Product Features

    The dustproof and waterproof design makes you feel at ease when installing the product outdoors or exposing it to rain. • ir mode (SnD-L5083r/Sno-L5083r/Snv-L5083r) If the IR indicator turns on, the product switches to the IR mode for preventing an object from being too bright, which helps you identify the object in near distance.

  • Page 10: Recommended Pc Specifications

    overview recommenDeD pc SpecificationS • CPU : Intel Core 2 Duo 2.4 GHz or higher Web Plug-in is optimized to SSE 4.1 Instruction Set. • Resolution : 1280X1024 pixels or higher (32 bit color) • RAM : 2GB or higher •...

  • Page 11: Recommended Micro Sd/Sdhc

    recommenDeD micro SD/SDHc memory carD SpecificationS • Recommended capacity : 4GB ~ 32GB • For your camera, we recommend you use a memory card from the following manufacturers: Micro SD/SDHC Memory Card : Sandisk, Transcend • Memory cards with a specification of Class 10 + UHS-1 or higher are recommended. naS recommenDeD SpecS •...
  • Page 12 Please check if your camera and accessories are all included in the product package. Appearance Item Name Quantity Description Model Name SND-L5013 or SND-L5083R or Camera SNO-L5083R or SNV-L5083R SND-L5013/ Instruction book, SND-L5083R/ Installer S/W CD SNO-L5083R/...
  • Page 13 Appearance Item Name Quantity Description Model Name SND-L5013/ SND-L5083R Useful for installation on the Tapping Screw ceiling, wall, etc. SNO-L5083R/ SNV-L5083R It protects the camera from the Sunshield SNO-L5083R direct sunlight. It fixes the sunshield with the Sunshield Hold SNO-L5083R camera.
  • Page 14 Used for assembling the dome case when installing the product Machine Screws SNV-L5083R on the pipe, wall mount, etc. or blocking a hole. Options (not included) Housing for installing indoor SND-L5083R/ Indoor Buried Housing buried type cameras SNV-L5083R 14_ overview...

  • Page 15: At A Glance (Snd-L5013

    at a GLance (SnD-L5013) appearance Item Description Dome cover Case cover used to protect the lens and the main unit. Camera Case Housing part that covers the camera body. English _15...
  • Page 16 overview components RESET 16_ overview...
  • Page 17 Item Description Internal Cover It is a cover to protect the main body. Lens Lens for the camera. The button restores all camera settings to the factory default. Press and hold for about 5 seconds to reboot the system. If you reset the camera, the network settings will be adjusted so that Reset Button DHCP can be enabled.

  • Page 18: At A Glance (Snd-L5083R

    GLance (SnD-L5083r) appearance Item Description Dome cover Case cover used to protect the lens and the main unit. Camera Case Housing part that covers the camera body. 18_ overview...
  • Page 19 components English _19...
  • Page 20 overview Item Description Internal Cover It is a cover to protect the main body. Illumination Sensor Detects incoming light to control the IR LED. IR LED These infrared LED’s are controlled by the illumination sensor. Lens Lens for the camera. Zoom in (Tele) Zoom out (Wide) Zoom control lever...
  • Page 21 at a GLance (Sno-L5083r) appearance English _21...
  • Page 22 overview Item Description The button restores all camera settings to the factory default. Press and hold for about 5 seconds to reboot the system. If you reset the camera, the network settings will be adjusted so that Reset Button DHCP can be enabled. If there is no DHCP server in the network, you must run the IP Installer program to change the basic network settings such as IP address, Subnet mask, Gateway, etc., before you can connect to the network.
  • Page 23 components Item Description Audio In Jack Used to connect to a microphone. PoE Connector Connects to the network and supplies power through Ethernet cable. IR LED These infrared LED’s are controlled by the illumination sensor. Illumination Sensor Detects incoming light to control the IR LED. English _23...
  • Page 24 overview at a GLance (Snv-L5083r) appearance Item Description Dome cover Case cover used to protect the lens and the main unit. Camera Case Housing part that covers the camera body. 24_ overview...
  • Page 25 components a b c English _25...
  • Page 26 overview Item Description Lens Lens for the camera. Illumination Sensor Detects incoming light to control the IR LED. IR LED These infrared LED’s are controlled by the illumination sensor. Zoom in (Tele) Zoom out (Wide) Zoom control lever By rotating it to the right or the left, the lens zoom can be adjusted. By rotating it clockwise, the zoom can be fixed.
  • Page 27 & connection inStaLLation (SnD-L5013/SnD-L5083r) precautions before installation Ensure you read out the following instructions before installing the camera: • It must be installed on the area (ceiling or wall) that can withstand 5 times the weight of the camera including the installation bracket.
  • Page 28 installation & connection installation 1. Attach the installation template to the selected area and punch 3 holes as shown in the figure. 2. Use the 2 supplied screws to fix the camera to the 2 punched holes. Set the <FRONT> mark imprinted on the camera to face the direction of camera monitoring.

  • Page 29: Installation (Sno-L5083R

    inStaLLation (Sno-L5083r) This camera is waterproof and in compliance with the IP66 spec, but the jack connected to the external cable is not. You are recommended to install this product below the edge of eaves to prevent the cable from being externally exposed. precautions before installation Ensure you read out the following instructions before installing the camera: •...
  • Page 30 installation & connection How to connect the rJ45 waterproof cable to a Lan cable 1. Insert it through the arrow direction. 2. Connect the LAN connector (male) to the cable. 3. Connect the RJ45 modular jack (female) to RJ45 connector the RJ45 connector (male).

  • Page 31: Outdoor Installation

    outdoor installation When you install it outside of the building, please waterproof it with waterproof butyl rubber tape (can be purchased in stores) so that water does not leak from the gap of the cable connected to the outside. 1. Connect the cable. Camera System 2.
  • Page 32 installation & connection to adjust the zoom factor or focus 1. Loosen the front cover as shown. 2. Loosen the zoom/focus lever slightly. 3. Position the zoom/focus lever to WIDE (NEAR) or TELE (FAR) as appropriate. 4. Then, tighten the zoom/focus lever to fix the adjusted position. 5.

  • Page 33: Installation (Snv-L5083R

    inStaLLation (Snv-L5083r) This camera is waterproof and in compliance with the IP66 spec, but the jack connected to the external cable is not. You are recommended to install this product below the edge of eaves to prevent the cable from being externally exposed. precautions before installation Ensure you read out the following instructions before installing the camera: •...
  • Page 34 installation & connection installation 1. Drill a hole (3mm diameter and minimum depth of 10 mm) for an installation screw using the template provided. FRONT FRONT FRONT FRONT 2. Align the installation hole of the camera to the previously drilled hole, and then insert a screw and tighten.
  • Page 35 connecting waterproof audio cable 1. Remove the dome cover and the case. 2. Pull out the rubber plug on the bottom as shown in the figure. 3. Insert the waterproof audio cable into the hole that was made by removing the rubber plug in step 2 above, and connect it to the connector.
  • Page 36 installation & connection attaching to the unbundled adapter Choose and purchase a necessary one of the following options (unbundled) that is suitable to the installation site or for your convenience. 1. Remove the dome cover from the case by referring to the “Disassembling”...

  • Page 37: Optional Accessories For Installation

    For your easier installation, you can purchase appropriate optional accessories available. 1. WALL MOUNT ADAPTOR(SBP-300WM or SBP-300WM1)/HANGING MOUNT (SBP-301HM2 : SNV-L5083R, SBP- 301HM4 : SND-L5083R, SBP-300HM7 : SND-L5013) This adaptor is used when installing the dome camera onto a wall.
  • Page 38 installation & connection 3. POLE MOUNT ADAPTOR(SBP-300PM) This is an adaptor for WALL MOUNT ADAPTOR (SBP-300WM or SBP-300WM1) installation on a pole whose diameter is bigger than 80mm. 4. CORNER MOUNT ADAPTOR (SBP-300KM) This is an adaptor for WALL MOUNT ADAPTOR (SBP-300WM or SBP-300WM1) installation on the corner of wall joint.

  • Page 39: Adjusting The Monitoring Direction

    (SnD-L5013/ SnD-L5083r/Snv-L5083r) FRONT NETWORK NETWORK LINK LINK Tilt Lens rotation ` adjusting the monitoring direction You can adjust the camera direction only when the camera is fixed on the ceiling. Where, rotating the camera unit to the left or right is called Pan, adjusting the tilt is called Tilt, and turning the lens on its axis is called Rotation.

  • Page 40: Inserting/Removing A Micro Sd

    Do not insert the Micro SD memory card while it’s upside down by force. Otherwise, it may damage the Micro SD memory card. inserting a micro SD memory card Push the Micro SD memory card in the direction of the arrow shown in the diagram. RESET RESET <SND-L5013/SND-L5083R> <SNO-L5083R> 40_ installation & connection...
  • Page 41 <SNV-L5083R> removing a micro SD memory card Gently press down on the exposed end of the memory card as shown in the diagram to eject the memory card from the slot. RESET RESET <SND-L5013/SND-L5083R> English _41...
  • Page 42 installation & connection <SNO-L5083R> <SNV-L5083R> Pressing too hard on the Micro SD memory card can cause the card to shoot out uncontrollably from the slot when released. Before removing your Micro SD memory card, turn off the camera or go to <Storage>, turn the device off, and press the [Apply ( )] button.
  • Page 43 memory carD information (not incLuDeD) what is a memory card? The memory card is an external data storage device that has been developed to offer an entirely new way to record and share video, audio, and text data using digital devices. Selecting a memory card that’s suitable for you Your camera supports Micro SD/SDHC memory cards.

  • Page 44: Connecting With Other Device

    & connection connectinG witH otHer Device <SND-L5013/SND-L5083R> PoE Device <SNO-L5083R> 44_ installation & connection...

  • Page 45: Ethernet Connection

    <SNV-L5083R> ethernet connection Connect the Ethernet cable to the local network or to the Internet. English _45...
  • Page 46 installation & connection powering and networking Connect the PoE device and camera’s PoE connectors. Connect to a PoE (Power over Ethernet) enabled router’s PoE connector. Use PoE that is compliant with the IEEE802.3af protocols. If you want to connect an external device, you must turn off the external device before proceeding. network cable Specification Item Contents...
  • Page 47 connecting to audio input Speaker Microphone Network Microphone Microphone <SNO-L5083R> English _47...
  • Page 48 As a microphone is built in, you can use the built-in microphone instead of an external one. (It is applicable only to the SND-L5013/SND-L5083R model.) 2. Check the specifications for audio input. • audio codec - Audio In : G.711 PCM (Bit Rate: 64kbps / Sampling Frequency: 8kHz), G.726...

  • Page 49: Connecting The Camera Directly To Local Area

    network connection and setup You can set up the network settings according to your network configurations. connectinG tHe camera DirectLy to LocaL area networKinG connecting to the camera from a local pc in the Lan 1. Launch an Internet browser on the local PC. 2.

  • Page 50: Connecting The Camera Directly

    network connection and setup connectinG tHe camera DirectLy to a DHcp BaSeD DSL/caBLe moDem INTERNET FRONT FRONT NETWORK NETWORK LINK LINK DSL/Cable Modem External Remote PC Camera DDNS Server (Data Center, KOREA) 1. Connect the user PC directly with the network camera. 2.

  • Page 51: To A Pppoe Modem

    connectinG tHe camera DirectLy to a pppoe moDem INTERNET FRONT FRONT NETWORK NETWORK LINK LINK PPPoE Modem External Remote PC Camera DDNS Server (Data Center, KOREA) 1. Connect the user PC directly with the network camera. 2. Run the IP Installer and change the IP address of the camera so that you can use the web browser on your desktop to connect to the Internet.

  • Page 52: Connecting The Camera To A

    network connection and setup connectinG tHe camera to a BroaDBanD router witH tHe pppoe/caBLe moDem This is for a small network environment such as homes, SOHO and ordinary shops. FRONT FRONT NETWORK NETWORK LINK LINK Camera INTERNET PPPoE or PPPoE or Broadband Cable Modem Cable Modem...

  • Page 53: Buttons Used In Ip Installer

    ButtonS uSeD in ip inStaLLer e f g Item Description Model name of the connected camera. Device Name Click the column to sort the list by model name. However, search will be stopped if clicked during the search. Alias This function is not currently implemented. Displays either <Static>, <Dynamic>...

  • Page 54: Static Ip Setup

    Exits the IP Installer program. For the IP installer, use only the installer version provided in the installation CD or use the latest one if available. You can download the latest version from the Samsung web site (www.samsungcctv.com). Static ip Setup manual network Setup Run <ip installer_v2.XX.exe>...
  • Page 55 3. In the <address> pane, provide the necessary information. • MAC (Ethernet) Address : The MAC address imprinted on the camera label is automatically displayed and requires no user setting. IP related parameters can be set only when DHCP is not checked. if not using a Broadband router For setting <ip address>, <Subnet mask>, and <Gateway>, contact your network administrator.
  • Page 56 network connection and setup if using a Broadband router • IP Address : Enter an address falling in the IP range provided by the Broadband Router. ex) 192.168.1.2~254, 192.168.0.2~254, 192.168.XXX.2~254 • Subnet Mask : The <Subnet mask> of the Broadband Router will be the <Subnet mask>...
  • Page 57 auto network Setup Run <ip installer_v2.XX.exe> to display the camera search list. At the initial startup, both [auto Set] and [manual Set] will be grayed out. For cameras found with the IPv6 setting, these buttons will be grayed out as the cameras do not support this function.

  • Page 58: Dynamic Ip Setup

    network connection and setup Dynamic ip Setup Dynamic ip environment Setup • Example of the Dynamic IP environment - If a Broadband Router, with cameras connected, is assigned an IP address by the DHCP server - If connecting the camera directly to modem using the DHCP protocols - If IPs are assigned by the internal DHCP server via the LAN checking the Dynamic ip 1.

  • Page 59: Port Range Forward (Port Mapping

    port ranGe forwarD (port mappinG) Setup If you have installed a Broadband Router with a camera connected, you must set the port range forwarding on the Broadband Router so that a remote PC can access the camera in it. manual port range forwarding 1.
  • Page 60 Port forwarding can be done without additional router setup if the router supports the UPnP (Universal Plug and Play) function. After connecting the network camera, set <Quick connect> of <Samsung DDNS> to <On> in the “Setup  Network  DDNS” menu.

  • Page 61: Connecting To The Camera From A

    connectinG to tHe camera from a SHareD LocaL pc 1. Run the IP Installer. It will scan for connected cameras and display them as a list. 2. Double-click a camera to access. The Internet browser starts and connects to the camera. Access to the camera can also be gained by typing the camera's IP address in the address bar of the Internet browser.

  • Page 62: Connecting To The Camera

    web viewer web viewer connectinG to tHe camera normally, you would 1. Launch the Internet browser. 2. Type the IP address of the camera in the address bar. ex) • IP address (IPv4) : 192.168.1.100  http://192.168.1.100 - the Login dialog should appear. •...
  • Page 63 To register your device to the <DDnS> server, visit www.samsungipolis.com and register your device first, and then set the Web Viewer’s <network> - <DDnS> to <Samsung DDnS>, as well as providing <product iD> that had been used for DDNS registration.

  • Page 64: Password Setting

    web viewer paSSworD SettinG When you access the product for the first time, you must register the login password. When the “password change” window appears, enter the new password. For a new password with 8 to 9 digits, you must use at least 3 of the following: uppercase/lowercase letters, numbers and special characters.
  • Page 65 inStaLLinG Stw webviewer pLuGin If connecting to a camera for the first time, you will see the installation message. Then, install the required WebViewer Plugin to access the camera and control the video from it in real time. 1. When the monitoring page is accessed for the very first time, the installation page is displayed.
  • Page 66 web viewer 5. Click [oK]. The old version of Web Viewer Plug-in is deleted. 6. Click [install] to begin installation of the Web Viewer Plug-in. 7. Click [finish]. STW Web Viewer Plug-in installation is completed. In your internet explorer, if you need to move to the installation screen after installing the STW webviewer plugin, check whether webviewer_...

  • Page 67: Using The Live Screen

    uSinG tHe Live Screen Item Description Monitoring Move to the monitoring screen. Move to the screen where you can search for the video recording saved in your Micro Playback SD memory card or NAS. Setup Move to the Setup screen. Profile access You can read the profile information.
  • Page 68 web viewer Item Description You can select a profile type in <Video profile> under the <Basic> setup menu. When the Web Viewer is connected, the profile information currently using is displayed. Afterimages can be displayed on the screen under the following conditions if the Profile type video is played in the monitoring page: The resolution is changed due to a profile change.
  • Page 69 to capture the snapshot 1. Click [capture ( )] on the scene to capture. 2. When a captured video is saved, a notification message appears. When using Internet Explorer, the captured video is saved in My Computer / My Documents / Pictures. In Mac OS, it is saved in “~/Pictures”...
  • Page 70 web viewer pLayinG tHe recorDeD viDeo Before you can play the video, you must configure the record settings. For details on record settings, refer to “Storage”. (page 107) name of event search screen and its function Item Description Set the search date and time range for data saved in your Micro SD memory Search range setting card or NAS.
  • Page 71 to play the content after searching by event 1. Click the [playback ( )] button. 2. Specify the start time and end time of your search. 3. Select an event type for your search within the specified period. 4. Click the [event search] button. The search results will be displayed in the list.
  • Page 72 web viewer name of time search screen and its function Item Description Time bar The section in the specific period is played by moving the time bar. Set the search date using the calendar. Search date setting If there is data saved in your Micro SD memory card or NAS on the day, it is marked as a box on the calendar.
  • Page 73 Item Description Video information Time data of the replayed video is displayed on the screen. Set the desired date to make a backup copy of video data saved in your Backup Micro SD memory card or NAS. Can be set as up to 5 minutes. to play after searching by time 1.
  • Page 74 web viewer 6. Move [time bar ( )] to a desired time point of the video before playing it. The time containing a normal recoding file will be highlighted in blue; the time with the event recording will be highlighted in red. to back up the searched video 1.
  • Page 75 to play an avi file (1) micro SD memory card 1. Separate the Micro SD memory card from the camera. Before separating the Micro SD memory card, set the <Device> to <Off> in the “Setup  Event  Storage” menu. 2.
  • Page 76 web viewer (2) naS (network-attached Storage) 1. In Windows browser, use \\<ip address>\ to access. ex)\\192.168.20.31\defaultfolder\ch01\ img\2013_07_02\AVI 2. Go to <computer>  <network drive connection>  Enter 1. 3. Connected to the NAS. The directory structure is same as the directory structure for a Micro SD memory card.

  • Page 77: Basic Setup

    setup screen Setup On the network, you can set up basic information on the camera, video and audio, network events and system. 1. In the Live screen, click [ Setup ( ) ] . 2. The Setup screen appears. The setting page for preview video requires the STW web viewer plug-in to be installed on the PC. If it is not intalled properly, the installation page automatically apprears.
  • Page 78 setup screen 4. Select each profile properties. For more details, refer to “to add/change the video profile”. (Page 80) 5. Click the input box of each item and enter / select a desired value. The context menu may differ depending on the selected codec type. •...
  • Page 79 • ATC sensitivity : Affect the transfer rate according to the variance in the network bandwidth. The transfer rate will be adjusted to the fastest if the bandwidth is <very high>, and adjusted to the latest if the bandwidth is <very low>. •...
  • Page 80 setup screen to add/change the video profile The profile setup can be added or modified to accommodate various profiles depending on the recording conditions. 1. Select one from the <video profile> options. 2. Provide the name and select a codec. 3.
  • Page 81 • Encoding priority : You can set the priority of video transmission to frame rate or compression. • GOV length : It specifies the distance (in terms of number of frames) between two consecutive I-Frames in a video sequence when H.264 codec was selected. (One I-Frame + 0~Several P-Frames) •...
  • Page 82 setup screen user 1. From the Setup menu, select the <Basic ( )> tab. 2. Click <user>. 3. Provide the necessary user information. • Administrator password change : Change the password for the administrator. For the security purposes, you are recommended to use a combination of numbers, alphabets uppercase and lowercase and special characters for...
  • Page 83 If the existing password is not matched, when you change the admin password, you cannot change the password. After changing your password, if there is a camera connected to a CMS or NVR client, then you need to re-register it with the newly changed password. If the camera is still connected with the same password, then the account may be locked because a client uses the previous password.
  • Page 84 setup screen Date & time 1. From the Setup menu, select the <Basic ( )> tab. 2. Click <Date & time>. 3. Specify the time and date that will be applied to the camera. • Current system time : Displays the current time settings of your system.
  • Page 85 ip & port 1. From the Setup menu, select the <Basic ( )> tab. 2. Click <ip & port>. 3. Set the <ipv4 setup>. • IP type : Select an IP connection type. - Manual : Specify the IP address, Subnet mask, Gateway, DNS1, and DNS2.

  • Page 86: Event Setup

    • Use timeout : When connecting to RTSP, this function resets the connection if there’s no response for a certain time. • Device port : Set a port used to transfer video signals with the Samsung protocols. If changed the HTTP port, the browser exits.

  • Page 87: Video Setup

    viDeo & auDio Setup video setup 1. From the Setup menu, select the <video & audio ( )> tab. 2. Click <video setup>. 3. Select a <video source> mode. • Flip mode : Turn upside down the image that is captured by the camera.
  • Page 88 (SnD-L5013/SnD-L5083r) You can configure the input values of an audio connected to a camera. 1. From the Setup menu, select the <video & audio ( )> tab. 2. Click <audio setup>. 3. Set the audio input value.
  • Page 89 audio setup (Sno-L5083r/Snv-L5083r) You can configure the input values of an audio connected to a camera. 1. From the Setup menu, select the <video & audio ( )> tab. 2. Click <audio setup>. 3. Set the audio input value. • Source : Sets the audio input. - Line : Connect the cable to the audio device.

  • Page 90: Camera Setup

    Refer to “Video profile” for the framerate setup range of the <Video profile> according to mode setup. (Page 77) to Set SSDr (Samsung Super Dynamic range) In a scene where the difference between bright and dark is severe, you can increase the brightness of the dark area alone to regulate the overall brightness.
  • Page 91 to Set white Balance You can correct the image colors based on white under any lighting conditions. 1. Select <white balance>. 2. Select <mode>. • ATW : Corrects the colors of the camera video automatically. • Manual : You can adjust the red and blue gains of the camera video manually. •...
  • Page 92 setup screen to Set BLc You can specify a desired area on the video manually and set the area to be displayed more clearly. 1. Select <Back light>. 2. Set <mode> to <BLc>. 3. Set <BLc level>. You can change the level to adjust the brightness of the monitoring area.
  • Page 93 to Set Day/night 1. Select <Day/night>. 2. Select each item and set it properly. • Mode : Mode is used to adjust the color of Color or Black and White. - Color : The video is always output in color. - B/W : The video is always output in black and white.
  • Page 94 setup screen to Setup Special 1. Select <Special>. 2. Select each item and set it properly. • Sharpness : Adjust the overall sharpness of the image. If selecting <on>, you can adjust the sharpness of the image. • Sharpness level : The higher the level is, the sharper and clearer the outline of the image becomes.
  • Page 95 to Set oSD 1. Select <oSD>. 2. Select each item and set it properly. • Camera title : It specifies the name of the camera to be displayed on the screen. • Camera title X, Y : It specifies the position of the camera name on the screen.

  • Page 96: Network Setup

    - User name : Enter the user name for the DDNS service. - Password : Enter the password for the DDNS service. 5. When done, click [apply ( If selected <Quick connect>, be sure to select Samsung DDNS service. 96_ setup screen...
  • Page 97 DDnS to register your product with the Samsung DDnS 1. Visit the iPOLiS web site (www.samsungipolis.com) and sign in with a registered account. 2. From the top menu bar, select <DDnS Service> - <my DDnS>. 3. Click [proDuct reGiStration].
  • Page 98 Samsung DDnS in camera setup 1. From the DDNS setup page, set <DDnS> to <Samsung DDnS>. 2. Provide the <product iD> that you registered product ID with the DDNS site. 3. Click [apply (...
  • Page 99 ip filtering You can create a list of IPs that you want to grant or deny access to them. 1. From the Setup menu, select the <network ( )> tab. 2. Click <ip filtering>. 3. Select <filtering type>. • Deny : If selecting this, access from those IPs that are added to the filtering will be restricted.
  • Page 100 setup screen You can select a secure connection system or install the public certificate for this purpose. 1. From the Setup menu, select the <network ( )> tab. 2. Click <SSL>. 3. Select a secure connection system. To access the camera using HTTPS mode, you have to type the IP address for the camera in the form of “https://<Camera_IP>”.
  • Page 101 802.1x When connecting network, you can choose whether using 802.1x protocol, and then install the certification. 1. From the Setup menu, select the <network ( )> tab. 2. Click <802.1x>. 3. Set the <ieee 802.1x setting>. • IEEE 802.1x : Specify the use of the 802.1x protocol.
  • Page 102 setup screen You can specify the priority to secure a stable transfer rate for a specific IP. 1. From the Setup menu, select the <network ( )> tab. 2. Click <QoS>. 3. Click the [add ( )] button. The IP list will be created. 4.
  • Page 103 • Enable SNMP Trap : SNMP trap is used to send important events and conditions to the Admin. - Community : Enter the trap community name to receive messages. - IP address : Enter the IP address to which messages will be sent. - Authentication failure : It specifies whether an event shall be generated when the community information is invalid.
  • Page 104 • UPnP discovery : It specifies Able or Disable for UPnP Discovery. • Friendly name : Display the camera name. Friendly name is displayed in the format of SAMSUNG-<Model Name>-<MAC Address>. In the Windows operating system which basically supports UPnP, the cameras connected to the network are displayed.
  • Page 105 event Setup ftp / e-mail You can configure the FTP/E-mail server settings so that you can transfer the images taken with camera to your PC if an event occurs. 1. From the Setup menu, select the <event ( )> tab. 2.
  • Page 106 setup screen • E-mail configuration - Server address : To enter an SMTP address of the email server to transmit an event image. - Use authentication : Select whether to use authorization. - Use SSL : Specify the use of SSL. - ID : Enter the user ID for logging into the email server.
  • Page 107 Storage You can activate recording on your device, set the recording conditions, check the saved data capacity and format the device itself. 1. From the Setup menu, select the <event ( )> tab. 2. Click <Storage>. 3. Select a device to save data in. If your device is properly recording data, it will display “Recording”.
  • Page 108 • Record file type : It specifies the file format of the recorded images. - STW : It is Samsung Techwin’s unique file format. - AVI : It is the conventional avi format.
  • Page 109 5. Set <SD file System>. • Type : The camera supports VFAT and EXT4 for the SD card file system, which can be set by the user. (However, a separate application is required that allows the EXT4 file system to interact with the Windows OS.) If the setting is changed, the existing data will be formatted.
  • Page 110 setup screen 3. Click the [test] button to see if you can successfully connect to the NAS. If the success message is displayed, it means that you can successfully save data in the NAS. If the fail message is displayed, check the following. Confirm that the IP address of the NAS is valid.
  • Page 111 naS (network attached Storage) guide Since data may not be saved after a temporary network interruption when using NAS, it is recommended that you use SD at the same time to prevent loss of recorded images. If the setting allows a Micro SD memory card and the NAS to be simultaneously connected for use, the higher priority for recording goes to the NAS.
  • Page 112 setup screen 2. If you access it as an admin, the following screen will be displayed. Click the [control panel]. 3. Click the <Shared folder> in the file sharing and privilege menu. 4. Click the [create] button. 5. After entering the shared folder name(ID), click the [oK] button to create a shared folder.
  • Page 113 8. After clicking the [create] button, enter name(ID) and password. In this example, name(ID) is set to [testiD] and password is also set to [testiD]. According to the NAS recommendations, when you use Netgear’s NAS equipment, do not allocate the capacity for use. 9.

  • Page 114: Time Schedule

    setup screen time schedule You can set to save the video data at a certain interval as scheduled regardless of the actual occurrence of the event. 1. From the Setup menu, select the <event ( )> tab. 2. Click <time schedule>. 3.

  • Page 115: Tampering Detection

    tampering detection You can set to detect tampering attempts and trigger events, such as sudden change of camera’s framing direction, blocked lens and other overall change of scenes from the video. 1. From the Setup menu, select the <event ( )>...
  • Page 116 setup screen 6. Configure the operations to be executed when an event is detected. • FTP : To set whether or not to send FTP when an event is detected. Refer to “FTP / E-mail” for more details. (page 105) •...

  • Page 117: Motion Detection

    motion detection Can be set to generate an event signal when a motion detection event is detected. 1. From the Setup menu, select the <event ( )> tab. 2. Click <motion detection>. 3. Set whether or not to <enable>. 4. Set <Sensitivity>, <Size> and <area>. 5.
  • Page 118 setup screen Before using, set the minimum and maximum motion sizes to suit desired motion range to be detected. Detected size of an object may have difference with the actual size according to its shape. Up to 16 objects from the top side of the screen can be displayed. In the following cases, motion detection function may be degraded or cause improper detection.
  • Page 119 to use motion detection It detects a motion that meets all conditions specified by sensitivity, size and area. 1. Select a motion detection mode. 2. Select <Sensitivity> tab to set the sensitivity level. You can set the sensor’s sensitivity to detect a motion out of the background from the monitoring video.
  • Page 120 setup screen 4. Select <area> tab. You can specify an area on the screen to include or exclude the area to/from detection. You can specify up to 4 areas. • Detection area : Sets the entire screen as excluded from detection, and adds specified area as motion detection area.

  • Page 121: System Setup

    SyStem Setup product information 1. From the Setup menu, select the <System ( )> tab. 2. Click <product information>. 3. Check the camera information, or provide details according to your network environment. • Model : Model name of the product. •...
  • Page 122 setup screen upgrade / reboot 1. From the Setup menu, select the <System ( )> tab. 2. Click <upgrade / reboot>. 3. Select a desired item and set it appropriately. • Upgrade : Performs upgrading the system. • Factory default : Resets the system to the factory default.
  • Page 123 If you forcibly terminate the upgrade process, upgrade will not be completed properly. During restarting the system, accessing with web viewer will not be made. You can download the latest version from the Samsung web site (www.samsungcctv.com). English _123...
  • Page 124 setup screen to back up the current settings 1. Click [Backup]. The Save As dialog should appear. 2. Specify the backup path with a proper file name, and click [Save]. The backup file will be saved to the specified path in the format of “.bin”. to restore the backup settings 1.
  • Page 125 You can check the system log or event log. 1. From the Setup menu, select the <System ( )> tab. 2. Click <Log>. 3. Select a log type. • System : You can check the system logs where any system changes are recorded including the time information.
  • Page 126 setup screen viewinG profiLe information profile access You can check the profile information. 1. Click [Status ( )] on the live screen. 2. The profile information screen is displayed. • Profile access : Show the information of the newly added profile. - Profile : Show the information of the newly added codec.
  • Page 127 Specification Description Items SND-L5013 SND-L5083R SNO-L5083R SNV-L5083R Imaging Device 1/3" 1.37M CMOS Total Pixels 1,312(H) x 1,069(V) Effective Pixels 1,305(H) x 1,049(V) Scanning System Progressive Video Color : 0.085 Lux (1/30sec, Color : 0.04 Lux (1/30sec, F1.4), 0.001 Lux (2sec, F1.8), 0.0008...
  • Page 128 True Day & Night Night Backlight Off / BLC Compensation Contrast Enhancement SSDR (Samsung Super Dynamic Range) (Off / On) Digital Noise Reduction SSNR (Off / On) Motion Detection Off / On (4ea rectangler zones) Privacy Masking Off / On (6ea rectangler zones)
  • Page 129 Description Items SND-L5013 SND-L5083R SNO-L5083R SNV-L5083R Ethernet RJ-45 (10/100BASE-T) Video Compression H.264, MJPEG Format 1280x1024 / 1280x960 / 1280x720 / 1024x768 / 800x600 / 720x576 Resolution / 640x480 / 320x240 H.264 : Max 30fps at all resolutions Max. Framerate MJPEG : 1280x1024/1280x960/1280x720/1024x768 : Max. 1 fps, Max.
  • Page 130 Description Items SND-L5013 SND-L5083R SNO-L5083R SNV-L5083R HTTPS(SSL) Login Authentication Digest Login Authentication Security IP Address Filtering User access Log 802.1x Authentication Streaming Method Unicast / Multicast Max. User Access 6 users at Unicast Mode Micro SD/SDHC Max 32G, NAS...
  • Page 131 Description Items SND-L5013 SND-L5083R SNO-L5083R SNV-L5083R -30°C ~ +55°C (-22°F ~ Operating Temperature -10°C ~ +55°C (+14°F ~ +131°F) / Less than 90% RH / Humidity * Start up should be done at above +131°F) / Less than 90% RH -20°C...

  • Page 132: Product Overview

    appendix proDuct overview SnD-L5013 Unit : mm (inch) Ø 110 [4.334] 132_ appendix...
  • Page 133 SnD-L5083r Unit : mm (inch) Ø 119.8 (4.71") Ø 89 (3.5") English _133...
  • Page 134 appendix Sno-L5083r Unit : mm (inch) 259.3 [10.21"] 152.0 [5.98"] 130.2 [5.13"] 115.8 [4.56"] 246.0 [9.69"] Ø 70.0 [2.76"] 3- Ø 5.5 HoLeS Ø 65.5 [2.58"] (BoDy) 75.2 [2.96"] 134_ appendix...
  • Page 135 Snv-L5083r Unit : mm (inch) Ø 137 (5.39") Ø 100 (3.93") English _135...

  • Page 136: Troubleshooting

    appendix trouBLeSHootinG PROBLEM SOLUTION y Check to make sure that the camera’s Network settings are appropriate. y Check to make sure that all network cables have been connected properly. I can’t access the camera from a y If connected using DHCP, verify that the camera is able to acquire web browser.
  • Page 137 PROBLEM SOLUTION Cannot record into the Micro SD y Check if the memory card is defective. memory card. y Check if the memory card is inserted in the proper direction. Operation Micro SD memory card is inserted of memory card that is formatted by other devices is not guaranteed with but the camera does not operate this camera unit properly.
  • Page 138 Corresponding Source code from us for a period of three years after our last shipment of this product by sending email to help.cctv@samsung.com If you want to obtain the complete Corresponding Source code in the physical medium such as CD-ROM, the cost of physically performing source distribution might be charged.
  • Page 139 Gnu GeneraL puBLic LicenSe The “Program”, below, refers to any such program or work, and a “work based on the Program” means either Version 2, June 1991 the Program or any derivative work under copyright law : that is to say, a work containing the Program or a portion Copyright (C)1989, 1991 Free Software Foundation, Inc.
  • Page 140 3. You may copy and distribute the Program (or a work 7. If, as a consequence of a court judgment or allegation of based on it, under Section 2)in object code or executable patent infringement or for any other reason (not limited to form under the terms of Sections 1 and 2 above provided patent issues), conditions are imposed on you (whether that you also do one of the following :...

  • Page 141: Gnu General Public License

    no warranty You should also get your employer (if you work as a programmer)or your school, if any, to sign a “copyright 11. BECAUSE THE PROGRAM IS LICENSED FREE OF disclaimer” for the program,if necessary. Here is a sample ; CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM, alter the names: TO THE EXTENT PERMITTED BY APPLICABLE LAW.
  • Page 142 Finally, every program is threatened constantly by software The “Corresponding Source” for a work in object code form patents. States should not allow patents to restrict means all the source code needed to generate, install, and development and use of software on general-purpose (for an executable work) run the object code and to modify omputers, but in those that do, we wish to avoid the special the work, including scripts to control those activities.
  • Page 143 5. conveying modified Source versions. d) Convey the object code by offering access from a designated place (gratis or for a charge), and offer You may convey a work based on the Program, or the equivalent access to the Corresponding Source in modifications to produce it from the Program, in the form of the same way through the same place at no further source code under the terms of section 4, provided that you...
  • Page 144 7. additional terms. However, if you cease all violation of this License, then your license from a particular copyright holder is reinstated (a) “Additional permissions” are terms that supplement the provisionally, unless and until the copyright holder explicitly terms of this License by making exceptions from one or more and finally terminates your license, and (b) permanently, if of its conditions.
  • Page 145 14. revised versions of this License. In the following three paragraphs, a “patent license” is any express agreement or commitment, however denominated, The Free Software Foundation may publish revised and/ not to enforce a patent (such as an express permission or new versions of the GNU General Public License from to practice a patent or covenant not to sue for patent time to time.
  • Page 146 openSSL combined License The OpenSSL toolkit stays under a dual license, i.e. both the conditions of the OpenSSL License and the original SSLeay license apply to the toolkit. See below for the actual license texts. Actually both licenses are BSD-style Open Source licenses. In case of any license issues related to OpenSSL please contact openssl-core@openssl.org.
  • Page 147 SNMP v3 using both IPv4 and IPv6. For more additional This product includes software developed by the information, send email to help.cctv@samsung.com. Computer Science Department at University College Copyright (C) 2004, Kneschke, incremental London.
  • Page 148 3. Neither the name of the Regents of the University of 3. Neither the name of Thomas BERNARD nor the names California nor the names of its contributors may be used of its contributors may be used to endorse or promote to endorse or promote products derived from this software products derived from this software without specific prior without specific prior written permission.
  • Page 149 THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR MERCHANTABILITY AND FITNESS FOR A PARTICULAR...
  • Page 150 THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT THIS SOFTWARE IS PROVIDED BY APPLE AND ITS HOLDERS AND CONTRIBUTORS “AS IS” AND ANY CONTRIBUTORS “AS IS” AND ANY EXPRESS OR EXPRESS OR IMPLIED WARRANTIES, INCLUDING, IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY MERCHANTABILITY AND FITNESS FOR A PARTICULAR...
  • Page 151 Copyright (c) 2006 Free Software Foundation, Inc. mozilla public License Since we, at Samsung Techwin, used the Mozilla Firefox component without modifying the source code according to the MOZILLA Public license 1.1, we are not obliged to provide the source code of the corresponding component.
  • Page 152 1.11. "Source Code" means the preferred form of the Covered (d) Notwithstanding Section 2.2(b) above, no patent license is Code for making modifications to it, including all modules it granted: 1) for any code that Contributor has deleted from contains, plus any associated interface definition files, scripts the Contributor Version;...

  • Page 153: Disclaimer Of Warranty

    3.5. Required Notices. You must duplicate the notice in Exhibit 6.2. Effect of New Versions. Once Covered Code has been A in each file of the Source Code. If it is not possible to put such published under a particular version of the License, You may notice in a particular Source Code file due to its structure, then always continue to use it under the terms of that version.

  • Page 154: Limitation Of Liability

    8.3. If You assert a patent infringement claim against Participant 13. muLtipLe-LicenSeD coDe. alleging that such Participant’s Contributor Version directly or Initial Developer may designate portions of the Covered Code indirectly infringes any patent where such claim is resolved as Multiple-Licensed. Multiple-Licensedmeans that the Initial (such as by license or settlement) prior to the initiation of patent Developer permits you to utilize portions of the Covered Code infringement litigation, then the reasonable value of the licenses...
  • Page 155 the independent JpeG Group’s JpeG Software The software included in this product contains copyrighted software that is licensed under the JPEG license. • JPEG license - Code project . Generating Outline OpenGL, Libjpeg This distribution contains the sixth public release of the Permission is NOT granted for the use of any IJG author’s Independent JPEG Group’s free JPEG software.
  • Page 156 t-Kernel License - This Product uses the Source Code of T-Kernel under T-License granted by the T-Engine Forum(www.t-engine.org) t-License [License agreement for Source code of t-Kernel] established by T-Engine Forum on January 23, 2004 revised on June 17, 2004 revised on December 21, 2006 revised on March 24, 2009 article 1.
  • Page 157 article 4. License of Source code 4. The Distributor of Modification shall determine the name of the Modified Source Code subject to the rules separately 1. As provided for in this Article, T-Engine Forum shall established by T-Engine Forum and publish an appropriate notice as required by the rules on the Patch for Modification provide, and grant a license to use, the Source Code free and the Modified Source Code.
  • Page 158 article 9. indemnity distribute the Ported Source Code as the Source Code for T-Kernel. Provided, however, that the Ported Source Code 1. Neither T-Engine Forum nor the copyright holder of the may be treated in the same way as the Modified Source Code until the time of registration hereunder.

  • Page 159: End Of Terms And Conditions

    5. Submission of Contributions. Unless You explicitly state any form of electronic, verbal, or written communication sent to the Licensor or its representatives, including but otherwise, any Contribution intentionally submitted for not limited to communication on electronic mailing lists, inclusion in the Work by You to the Licensor shall be under source code control systems, and issue tracking systems the terms and conditions of this License, without any that are managed by, or on behalf of, the Licensor for...
  • Page 160 BZip2 License This program, "bzip2", the associated library "libbzip2", and all documentation, are copyright (C) 1996-2007 Julian R Seward. All rights reserved. component name License bzip2-1.0.5 Bzip2 http://www.bzip.org/ Redistribution and use in source and binary forms, with THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS or without modification, are permitted provided that the IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, following conditions are met:...
  • Page 161 pHp 3.01 License The PHP License, version 3.01 Copyright (c) 1999 - 2010 The PHP Group. All rights reserved. component name License php-5.2.17 PHP 3.01 http://www.php.net/distributions 6. Redistributions of any form whatsoever must retain the Redistribution and use in source and binary forms, with or without modification, is permitted provided that the following following acknowledgment: "This product includes PHP conditions are met:...
  • Page 162 Samsung Techwin cares for the environment at all product manufacturing stages, and is taking measures to provide customers with more environmentally friendly products.
  • Page 163 memo...
  • Page 164 SALES NETWORK SAMSUNG TECHWIN CO., LTD. 6, Pangyo-ro 319beon-gil, Bundang-gu, Seongnam-si, Gyeonggi-do, SEOUL 463-400 Rep. of KOREA Tel : +82-70-7147-8753, 8764 Fax : +82-31-8018-3740 www.samsungsecurity.com SAMSUNG TECHWIN AMERICA Inc. SAMSUNG TECHWIN EUROPE LTD. 100 Challenger Rd. Suite 700 Ridgefield Park, NJ 07660 2nd Floor, No.

This manual is also suitable for:

Snd-l5013Sno-l5083rSnv-l5083r

Table of Contents