Samsung SW12E1S(P)/XST Service Manual page 9

2. Washing Mode
1) After reading the selected water level and washing is carried out for 2 min or 9 min, the motor is off for 3 sec to read the fre-
quency of the water level. If the water level is lower than the selected water level, water is added to the selected water level and
then washing proceeds. The time for adding water does not exceed 30 sec.
* While in rinsing, water is added 1 min later after the rinsing cycle starts.
2) Table of Water Current Pattern during the washing cycle of each water level for each course according to the washing selection
(see the appendix)
3) For each course or each water level, the water addition mode is carried out 2 min or 9 min after the washing cycle starts and 1
min after the rinsing cycle starts. The time out is 30 sec.
Although the washing time is changed by the washing-adjusting key while in washing cycle after the water addition mode, the
water addition mode is not carried out.
4) In case that the water addition mode is carried out twice in a course, even though the time for any cycle is changed, no more
water addition mode is carried out.
5) When the washing time is changed after the water addition mode is carried out once, it is carried out once more within the
changed washing time.
2-3-2 Rinsing Cycle
1. Draining Mode
1) The draining valve is kept ON.
If the water level at the initial stage of this mode is higher than the reset, the delay mode is carried out for 50 sec after reading
the reset. If lower than the reset, it is carried out for 20 sec.
2) The remaining time decreases while the draining mode is carried out until the standard time for draining is over. After that, the
remaining time does not decrease any longer.
When this mode is done, the standard time for draining is considered to be over.
Water Level High
Draining Time 2 min 10 sec
3) When the water level is higher than the reset in 15 min after starting the draining mode, the draining error mode is carried out.
The buzzer sounds 5 times and the pause mode is carried out.
4) If the Start key is input during the step 3), the error is cleared, the time out is set to 15 min again, and then draining begins.
2. Intermittent Spin Mode
1) If the door is open while in this mode, this mode is paused and the door open alarm (5 times of the door open melody) sounds.
2) If the door is closed while the door open alarm sounds, the alarm stops and the operation proceeds in the same way when the
Start/Pause key is input.
3) When the safety S/W detects the unbalance while in this mode, the unbalance clearing mode is carried out.
Unbalance detecting mode
- Checker S/W detecting time: 20 ñ 449 ms
- When the door is open (Reed S/W detecting), the drive part is turned off immediately after 20 ms is detected.
When the door is closed while the door open alarm sounds, the alarm mode is canceled, the draining valve is on in 10
sec after it is off, and then the motor restarts after the draining valve is on.
Unbalance clearing mode
- When the unbalance occurs while in spinning after the washing cycle ends, this mode is carried out in the same way
when one rinsing cycle is added. When the unbalance is detected while in rinsing, water is supplied and then the next
rinsing step is proceeded. When the unbalance occurs during the final spin, the clearing mode is carried out up to twice.
At the third time, the unbalance alarm sounds.
- At the beginning of the clearing mode, 'the standard time for supplying water + 1 min' is added to the initial remaining
time of the corresponding cycle. The clearing mode is carried out with the disentangling water current for 1 min after
supplying water.
- When the unbalance error occurs, 'UE' flashes in the way of 1 sec ON/OFF and the error melody sounds 5 times.
- When the unbalance occurs while in the spin only mode, the error alarm sounds.
SAMSUNG ELECTRONICS CO., LTD
Medium Low
2 min 1 min 50 sec 1 min 30 sec
Small Minimum
1 min 20 sec
Remarks
Excluding 50 sec delay
7