Punch Through; Operating The Remote; Normal Operation - Universal Remote Control Home Theatre Master 1000 User Manual

– Each function key will hold one command only, a new command
to be learnt will automatically erase and replace the previous
one.
– If you have accidentally pressed an unexpected key in step 5
above, you have to wait 16 seconds until the indicator goes
out and the HTM1000 will go back to normal operation. You may
repeat the above procedures to setup the remote again.
– If the indicator flashes 3 times during the transference of the signals,
this tells you the memory bank is full. Press the same device key
again to resume normal operation. (You may erase the learned
commands in a device mode and make room for any new signal.
See "Warning" above.)
5

Operating the Remote

5.1 Normal Operation

Once you have setup the remote for your A/V equipment,
it works like your original remote controls. To operate, just
aim it at your equipment, press an appropriate device mode
key and invoke the desired function by pressing a
corresponding key on the remote. The indicator flashes
and you can hear beep sound during signal transmission
as confirmation of key touch.
For some VCR/DVD players, please use
buttons for performing PLAY/STOP/REW/FF and REC
functions.
5.2 Page
Each device mode contains 3 groups of commands. You
can simply tap the "
of the remote panel to turn to another command group.
5.3 Shift
" SHIFT " function allows you to obtain additional learning
space for each device mode. There are 3 pages for each
default device mode. Through using "
access the 4th, 5th and 6th pages. The practical procedures
are as follows:
5.3.1 Learn additional codes into the 4th, 5th and
6th pages
1. Follow step 1 to 4 of "
(Learning Commands) ".
SHIFT
2. Press " " key and you can see the "
changed to "
SHIFT
Page
" key on the right bottom corner
SHIFT
" key, you can
4 How to Set Up Your HTM1000
SHIFT
" .
9
English
3. Now, your HTM1000 is into the 4th page for additional
4. Follow the procedures from point 5 of section "
5.3.2 "Shift" for obtaining additional Macro(s)
Besides accessing additional learning spaces, " SHIFT "
function can also allow you to program the 4th, 5th and
6th " Smart " for performing Macro function. The setup
procedure, please refer to section " 6.1 Program the 4th, 5th
and 6th Smart ".
5.3.3 How to access the "Shift" function
1. Press the device mode key that you have previously
2. Press "
3. Your HTM1000 is now into the 4th page of chosen device
4. Find the function icon that you have learnt before and
5. To exit " SHIFT " mode, press the "

5.4 Punch Through

Punch through allows you to operate TV's volume and mute
functions without having to switch the device modes repeatedly
even when your remote is in other operating modes.
However, if you have learned commands on VOL+, VOL–
or
punch through function will be disabled in that corresponding
device mode.
5.5 Advanced Function – Smart Program
Create a chain of multiple commands
with 6 programmable Smart programs (
of Smart, you can program a group of commands in time
delay to execute in a chain of infra-red signal simply by a
press of Smart.
" key
Page
learning space. Press "
6th page.
to Set Up Your HTM1000 (Learning Commands) " for
remaining learning command setup.
learnt commands e.g.
SHIFT
", a "
SHIFT
mode e.g. " TV ".
press once to execute the command.
in the device mode (VCR, DVD, SAT, CBL), the
Smart 3
) each with maximum 20 key steps. With the help
10
English
" to access the 5th and
4 How
.
" can be seen.
SHIFT
" icon again.
– your remote comes
Smart 1 Smart 2
, ,