Learning Commands - Universal Remote Control Home Theatre Master 1000 User Manual

– Each time you press the "
to the next code and send out a POWER signal trying
to turn off your device.
If you failed to stop pressing "
device has been turned off, turn on your device again
immediately. Before the indicator goes out, press " P– "
on the HTM1000 to skip backward. Repeat the step 7
above and lock in code.
– If the indicator flashes 6 times after your pressing of "
key, you are already at the last code of the library. Press
the device mode key (e.g.
HTM1000 and repeat carefully the above procedures to
search again.
4
How to Set Up Your HTM1000

(Learning Commands)

Your HTM1000 is factory preprogrammed to operate your TVs,
VCRs, SATs, CBLs & DVDs. Due to the limited number of key,
some minor functions may not be included. You may teach your
remote with the original A/V remote to operate any excluded
function by your choice.
Besides the preprogrammed devices, you may also teach the
remote to operate other infra-red controlled equipment and
appliances, such as HiFi or air-conditioners, etc.
Your HTM1000 can learn and reproduce up to 226 commands
from other remote controls. All 5 device modes (TV, VCR, DVD,
SAT, CBL) can be taught to operate additional commands:–
1. Press a desired device mode key (e.g.
will change into blue color).
2. Hold down " P+ " & " VOL– " on the remote together simultaneously
for 3 seconds until the indicator lights up.
3. Enter the Magic Learn Code – 0000, the "
light up and your HTM1000 is ready to learn commands.
4. Aim your A/V remote control to the
HTM1000 infra-red lens on a flat sur-
face, with 5-8 cm apart. Make sure your
A/V remote control has new batteries.
5. Press and release a desired keys on the
remote you want to hold the command.
6. Press and hold the corresponding key on your A/V remote control
to transfer the command. The indicator will flash once and the
device mode key icon (e.g.
command is copied. You can release the key on the A/V remote
control. If the indicator flashes 6 times, it shows error in learning
process. Adjust the position of both remote controls and repeat
steps 5 to 6 again.
English
", the HTM1000 will skip
" in time when your
) to resume the
, "
Learn
" icon will
) will flash again when the
7
7. Repeat steps 5 to 6 to transfer other signals into next function
key. When you finish the whole device mode, press the same
device mode key (e.g.
indicator will flash twice and then turn off.
4.1 Learning Additional Codes by "SHIFT"
There are in maximum of 42 squares within 3 pages which
are available to be learnt for each device mode. In case
"
you would like to learn more than 42 commands per each
device, you can make use of " SHIFT " function to obtain
additional 3 more pages in order to obtain additional 42
free learning spaces under " SHIFT " platform. For detail
explanation of how to use the " SHIFT " function, please
refer to section " 5.3 SHIFT " for reference.
4.2 Advance Learning – Teaching a Dual Signal
If you found a learned command work for your A/V
equipment only occasionally, your original remote control
may contain dual signals. Try the following steps to
reprogram this command:–
1. Follow step 1 to 4 of "
(Learning Commands) ".
2. Press and release a desired key on the HTM1000 you
want to hold the command. The device mode key icon
(e.g.
3. Press and hold the corresponding key on your A/V remote
control to transfer the command. The indicator will flash
once and the device mode key icon (e.g.
again. The first signal has been transferred successfully
and you can release the key on the A/V remote control.
" icon
4. Press and release the same button on the HTM1000 again.
The device mode key icon (e.g.
5. Press and hold the same corresponding key on your
A/V remote control until the indicator will flash once and
the device mode key icon (e.g.
dual signal command has been transferred successfully.
6. Repeat steps 2 to 5 of this procedure to transfer other
signals if there is any.
7. When finished, press the same device mode key again
to store your setting.
Warning:
Entering a new preprogrammed device code will
automatically erase and replace all learned commands in
the chosen device mode.
Note:
– Do not attempt to learn additional commands with the Device
Mode Keys, "
hold commands by themselves.
) again to store your setting. The
4 How to Set Up Your HTM1000
) will stop flashing.
Page
SHIFT
" Key & "
8
English
) will flash
) will stop flashing.
) flash again. The
" Key. They will not