Maintenance; Troubleshooting - Universal Remote Control Home Theatre Master 1000 User Manual

6
Program a Smart
1. Hold down " P+ " & " VOL– " on the HTM1000 together
simultaneously for 3 seconds until the indicator lights up.
2. Enter the Magic Code – 0009.
3. The Smart icons will turn on.
4. Select a desired Smart key. (e.g.
5. Select a command from the corresponding device mode and
indicator will flash once for each key.
6. Press and hold the command if you want to setup the transmission
period of the command (max. up to 60 seconds).
7. Repeat step 5 until you finish the whole program and press
the same Smart key (e.g.
8. To program another Smart, repeat the steps 1 to 6 above.
6.1 Program the 4th, 5th and 6th Smart
1. Follow step 1 to 3 of section "
SHIFT " to enter " SHIFT " mode and then choose
2. Press "
Smart 1 Smart 2
,
Smart 5 Smart 6
and
3. The indicator will flash twice and keep light on. The
HTM1000 is ready to receive a series of commands.
4. Select a command from the corresponding device mode
and indicator will flash once for each key.
5. Press and hold the command if you want to setup the
transmission period of the command (max. up to 60
seconds).
6. Repeat step 5 until you finish the whole program and
SHIFT
press " " and the same Smart key (e.g.
The Smart program is stored.
6.2 Operating a Smart Program
1. Aim your remote at the equipment.
2. Press and release the Smart key that you have
programmed (e.g.
icon and the indicator will flash slowly during transmission
of the signals. The Smart icon and the indicator will stop
flashing when the chain of infra-red signals has been
transmitted completely. The remote will go back to normal.
6.3 Operating the 4th, 5th and 6th Smart
Program
1. Aim your remote at the equipment.
SHIFT
2. Press " " and choose the Smart key that you have
programmed (e.g.
icon and the indicator will flash slowly during transmission
of the signals. The Smart icon and the indicator will stop
flashing when the chain of infra-red signals has been
transmitted completely. The remote will go back to normal.
Smart 1
)
Smart 1
). The Smart program is stored.
6 Program a Smart ".
Smart 3
or and that represent
respectively.
Smart 1
). The corresponding Smart
Smart 1
). The corresponding Smart
11
English
7

Maintenance

– Do not expose your HTM1000 to dust, strong sunlight, humidity,
high temperature or mechanical shock.
– Do not use old and new batteries together as old batteries tend to leak.
– Do not use corrosive or abrasive cleansers on your HTM1000.
– Keep the unit dust free by wiping it with a soft, dry cloth.
– Do not disassemble your HTM1000, it contains no user-
serviceable parts.
8

Troubleshooting

Q. My remote does not work all !!!
A. Check your A/V device, if the main switch of the device is turned
off, your remote could not operate it.
A. Check whether your batteries are inserted properly and are
in correct +/– marks.
Smart 4
,
A. If the batteries are weak, replace the batteries. See " 1.4 How
to Install Batteries ".
Q. If several device codes listed under the brand of my A/V device,
how can I select the correct device code?
A. To seek the correct device code for your A/V device, test the
code one by one until most keys work properly.
Q. My A/V equipment responds only to some of the commands.
A. You have set a code for which only some commands work
Smart 1
).
properly but some do not. Try other codes until most keys work
properly.
A. You can also copy from the original A/V remote. See "
to Set Up Your HTM1000 (Learning Commands) ".
Q. My remote indicator shows error in learning commands from
other A/V remote control.
A. Make sure you are aiming your A/V remote control at the HTM1000
infra-red lens on a flat surface with 5-8 cm apart.
A. Make sure the learning procedures are carried out in an
environment free from direct sunlight and /or strong light.
A. Clean the infra-red transmission diode/lens of your A/V remote
and try again.
A. Check the batteries inside the A/V remote control. If the batteries
are weak, the remote cannot learn command properly.
A. Make sure the distance between the A/V remote and your
HTM1000 is remained the same throughout the whole learning
procedures.
Q. Some learned commands in my remote do not work.
A. Those signals are not learnt properly. Try to teach your
HTM1000 again for those functions.
English
12
4 How