Control Arm Set / 控制臂組裝 - THUNDER TIGER x50 Instruction Manual

Control Arm Set / 控制臂組裝
Bag F+I
No. Material No. Description
1 BK2248 PHASING CONTROL TRACK
2 BK2249 CANOPY RETAINING POST
3
HME3-18B SET SCREW,M3x18
4 HMC2-4B SOCKET SRCEW,M2x4
5 BK2271 GYRO TRAY
6
HNX3-12B S.B.H SELF TAPPING SCREW
7 BV2569-R
120° FB CONTROL ARM SET-R, 4757
8 BV2570-L
120° FB CONTROL ARM SET-L, 4757
9
BK2279 HEX POST
10 BK0649-1 LINKAGE BALL
HME3-18B
SET SCREW,M3x18
無頭內六角螺絲,M3x18
HMC2-4B
SOCKET SRCEW,M2x4
內六角螺絲,M2x4
HNX3-12B
S.B.H SELF TAPPING SCREW
半圓頭內六角自攻螺絲
HMC3-12B
SOCKET SCREW,M3x12
內六角螺絲,M3x12
HMM25Z
NYLON NUT,M2.5
止鬆螺帽,M2.5
BK0077
COLLAR,d3xD4xW6
軸環,d3xD4xW6
The hole with a round chamfer
goes toward the tail。
有倒角的孔徑朝向尾座。
(17)
1. Attach the Bearing into the Rubber Bearing Support.
2. Screw the Shaft End onto the Tail Drive Shaft with a drop of threadlocker
as the drawing, but do not over tighten.
3. Add a drop of thin CA glue on the Tail Drive Shaft next to where the
bearing should be, and then slide the bearings over the position quickly;
the distance from the Shaft Drive End to the Rubber Shaft Bearing
Support is approx. 350mm / 13.78".
4. Apply some amount of silicon oil or Vaseline onto the rubber surface for
easy install into the tail boom later.
名稱
相位控制導軌
機殼固定鋁柱
無頭內六角螺絲,M3x18
內六角螺絲,M2x4
陀螺儀座
半圓頭內六角自攻螺絲
120° 無平衡翼控制搖臂組(右), 4757
120° 無平衡翼控制搖臂組(左), 4757
內六角連接頭
內六角連接頭螺絲
BK0649-1
LINKAGE BALL
內六角連接頭螺絲
(5)
(6)
(3)
(2)
(4) (9)
(10)
(13)
(7)
(10)
Right Side
(12)
右側
Tail
尾座
(18)
(19)
(16)
Apply C.A Glue
使用快乾膠黏合
Apply threadlocker
使用螺絲防鬆膠
Qty No. Material No. Description
11 BK0088
1
2 12 BK0077
13
2 HSA3-10
14 BK2552
2
1 15 BK0367
16
4 BK2529
17 HMV1680ZZY
1
1 18 HMC2512B
19
2 HMM25Z
4
Secure all screws shown on this page with a drop of
thredlocker except the screws #4 and 6.
除螺絲＃4及6之外，本頁顯示之螺絲請使用適量防鬆膠鎖固。
(1)
(6)
(11)
(14)
-13-
WASHER, d3xD5xW0.5
COLLAR, d3xD4xW6
BUTTON HEAD SOCKET SCREW, M3x10
TAIL DRIVE SHAFT
TAIL DRIVE SHAFT LINKER
TAIL DRIVE SHAFT BRG
BEARING, d8xD16xW5
SOCKET SCREW,M3x12
NYLON NUT,M2.5
(2)
(3)
(4)
(8)
(9)
(11)
Note the "120L"/"120R" mark on the arms.
請按照控制臂左、右方向安裝。
CA
(19)
(18)
1. 將軸承擠壓入橡膠軸套內。
2. 參考圖示，塗抹些許防鬆膠將尾傳動軸接頭
鎖在尾傳動軸，但勿過度鎖緊。
3. 在尾傳動軸上軸承固定位置前方，塗抹少量
快乾膠，迅速滑動軸承至定位固定；該定位
大約距離軸傳動接頭350mm / 13.78"處。
4. 塗抹些許矽膠油脂或凡士林於橡膠軸套表面
上，稍後將尾驅動軸組裝入尾管時，會較為
容易。
Qty
名稱
墊片, d3xD5xW0.5 2
2
軸環, d3xD4xW6
2
半圓頭內六角螺絲, M3x10
1
尾驅動軸
2
尾驅動連接棒
1
傳動軸軸承套
1
滾珠軸承, d8xD16xW5
2
內六角螺絲, M2.5x12
2
止鬆螺帽, M2.5
(10)
Left Side
左側
(13)
(10)
(12)
CA
(15)
Nose
機頭