Tail Unit / 尾部總成組裝 - THUNDER TIGER x50 Instruction Manual

Tail Unit / 尾部總成組裝
Bag H+I
No. Material No. Description
1 BK2253 FRAME SPACER
2 HMC3-14B SOCKET SCREW , M3x14
3
HSA3-6 BUTTON HEAD SOCKET SCREW, M3X6
4 BK2563 METAL TAIL SUPPORT BRACKET(UPPER)
5 BK2564 METAL TAIL SUPPORT BRACKET(LOWER)
6
BK0524-T TAIL SUPPORT ROD
7 BK0447 TAIL SUPPORT ROD END
HMM3Z
NYLON NUT,M3
止鬆螺帽,M3
(3)
(2)
HMJ2-8N
SELF TAPPING SCREW-M2x8
自攻螺絲(細)-M2x8
HSA3-6
BUTTON HEAD SOCKET SCREW, M3X6
半圓頭內六角螺絲, M3x6
HMC3-14B
SOCKET SCREW,M3x14
內六角螺絲,M3x14
HMC3-16B
SOCKET SCREW,M3x16
內六角螺絲,M3x16
HMC3-10B
SOCKET SCREW,M3x10
內六角螺絲,M3x10
Must be purchased separately
改裝品需另購
名稱
六角支柱
內六角螺絲, M3x14
半圓頭內六角螺絲, M3x6
金屬固定座(上)
金屬固定座(下)
尾管支撐架
尾管支撐架接頭
(3)
(2)
(1)
(7)
(8)
Secure the screws into the Frame
Spacer when attaching the Tail
Support Rod End on the Main Frames.
安裝尾管支撐桿於側板上時，請注意需將
鎖固螺絲鎖固於六角固定支柱上。
This hole (Left & Right side
both) is design for 140°Control
Arms(PV1409)
此孔位（左右二側）用於140°控
制搖臂（PV1409）
Qty No. Material No. Description
1 8 HMJ2-8N SELF TAPPING SCREW, M2x8
2 9 HMC3-16B SOCKET SCREW, M3x16
10
2 HMM3Z NYLON NUT, M3
1 11 BK2553 SUPPORT BRACKET
1 12 HMC3-10B SOCKET SCREW, M3x10
13
2 HNJ-1 NYLON STRAP,100mm
4
Ensure the setting screws (#3) line up to the retaining hole.
鎖固時，請確認鎖固螺絲#3正確對正定位孔。
Stick some cycles of thin tape properly onto
the position where the Brackets clip to prevent
any indentation on the tail boom caused by
over tighten or vibration.
纏繞適當圈數薄膠帶於尾管固定座夾持位置上，可
避免因夾持過緊或機體震動而造成尾管上壓痕。
(4)
(6)
Rear View 後視圖
(2) (7)
-16-
名稱
自攻螺絲(細), M2x8
內六角螺絲, M3x16
止鬆螺帽, M3
支撐架
內六角螺絲, M3x10
束帶(小)
(9)
(8)
(5)
(7)
(10)
(1) (7) (2)
Apply threadlocker
使用螺絲防鬆膠
(13)
(10)
(11)
(11)
(12)
Qty
4
2
3
2
1
4
(13)