Main Gear Set / 主齒輪組裝 - THUNDER TIGER x50 Instruction Manual

Main Gear Set / 主齒輪組裝
Bag F
No. Material No. Description
1 ONE WAY BEARING SHAFT
BK2282
2 BV2281 ONE WAY CLUTCH HOUSING
3
BK2581 MAIN GEAR, 135T
4 BUTTON HEAD SOCKET SCREW,M3x8
HSA3-8
5 BK2524 MAIN GEAR WASHER
6
BK2582 AUTOROTATION TAIL DRIVE PULLEY,100T
Secure all screws shown on this page with a drop of thredlocker.
本頁顯示之螺絲請使用適量防鬆膠鎖固。
Note the chamfer
should point up.
注意有倒角端朝上
BV2281
HSA3-8
BUTTON HEAD SOCKET SCREW,M3x8
半圓頭內六角螺絲,M3x8
BK2524
MAIN GEAR WASHER,d14.2xD19xW0.5
主齒輪墊片,d14.2xD19xW0.5
HMC3-10B
SOCKET SCREW,M3x10
內六角螺絲,M3x10
BK0087
WASHER,d3xD8xW1.4
墊片,d3xD8xW1.4
BK1197
MAIN SHAFT BOLT,M3x20
內六角半牙螺絲,M3x20
BK2290
COLLAR,d10xD14xW9
軸環,d10xD14xW9
HMM3Z
NYLON NUT,M3
止鬆螺帽,M3
名稱
單向軸套
單向離合組
主齒輪, 135T
半圓頭內六角螺絲,M3x8
主齒輪墊片
軸傳尾驅動主齒,100T
(1)
(2)
(3)
(4)
(4)
(5)
(6)
1. Insert the Main Shaft into Main Gear Set, Main Gear Washer & Lower Bearing Block.
2. Line up the holes of the Autorotation Tail Drive Gear, One Way Bearing Shaft & Main
Shaft, and then insert the Socket Screw to fix them with a Nut. Add a drop of threadlocker
when securing, but do not over tighten.
3. Adjust the position of Lock Ring to eliminate play of the Main Shaft, and then secure the
set screws tightly with a drop of threadlock.
1. 將主軸依序穿過主齒輪組、主齒輪墊片及下軸承座。
2. 對正尾驅動齒、單向軸套及主軸上孔位後，穿入內六角螺絲並加上螺帽，並使用適量防鬆劑固定。
注意! 請勿過度緊迫螺絲。
3. 調整止擋環位置以消除主軸間隙後，著以適量防鬆膠鎖固。
(9)
(10)
Apply threadlocker
使用螺絲防鬆膠
Qty No. Material No. Description
1 7 SOCKET SCREW,M3x10
HMC3-10B
8
1 BK0087 WASHER,d3xD8xW1.4
9
1 BK1197 MAIN SHAFT BOLT,M3x20
4 10 COLLAR
BK2290
11
1 HMM3Z NYLON NUT,M3
1
(11)
(8)
(7)
-12-
Qty
名稱
4
內六角螺絲,M3x10
4
墊片,d3xD8xW1.4
內六角半牙螺絲,M3x20 1
1
軸環
1
止鬆螺帽,M3
(8)
(7)