Sampler - Denon DN-D6000 Operating Instructions Manual

SAMPLER

11
DN-D6000 has Sampler of 15 seconds length. This Sampler can also be looped and scratching during playback.
q r !0
, ,
y u !1
,
i !0 w o e t
, , ,
Record in Sampler
q When the SAMP button is
pushed in the standby or
playing, the sound from
SAMP point is recorded to
Sampler memory up to 15
seconds.
1
• The SAMP button is flashing while
recording. When the recording is
completed, the button turns off and the
corresponding SAMP B LED lights up.
• The remain time of the Sampler memory
is displayed in the character display.
Setting B point
w When the B button is
pushed during Sampler
recording, the Sampler Loop
B point is set and the loop
mode turns on.
2
• Recording continues for approximately
15 seconds without stopping after set B
point.
• If the B point is not set, recording end
point set as B point automatically. Also
EXIT/RELOOP LED light to indicates
Sampler Loop mode is set automatically.
!3 !4 !6
, , ,
!2 !5
,
Stop recording
e To stop recording before
recording finish
automatically with
3
memory full, push the
STOP button.
• The EXIT/RELOOP LED light to indicates
Sampler Loop mode is set automatically.
Play Sampler sound
r Playback of the Sampler
sound starts when the
SAMP button is pushed after
recording has stopped.
• Sampler playback continues in looping.
With setting B point, playback loop
between A and B point. Without B point
setting Sampler loops whole recorded
4
length (about 15 seconds).
t To stop the Sampler
sound push STOP button.
Select Sampler Loop mode
You can select loop mode for Sampler when
Sampler playback stop.
Loop (default):
Sampler playback continues with
looping.
(EXIT/RELOOP LED stays lit)
Exit: Sampler playback continues over B
5
point up to recording length.
(EXIT/RELOOP LED flashes)
Single: Sampler playback stops at B point.
(EXIT/RELOOP LED turned off)
y To select loop mode, push
EXIT/RELOOP button after
recording and before playing.
Exit and Reloop
u The EXIT/RELOOP button
6
can be used same as
Seamless Loop function.
Reverse Play
i You can play the Sampled
sound in reverse by pushing
the RVS button. In reverse play
mode RVS LED lights up.
7
• Reverse playback will take affect when
you push the SAMP button after reverse
mode has been turned on. To return to
normal forward playback, push the RVS
button once again.
Moving Sampler B point
o When the B button is
pushed during Sampler
8
playback, the B point moves
to the point at which the
button was pushed, and loop
playback from point A starts.
Clearing the Sampler data
!0 While pressing the RVS/(CLR) button,
push the SAMP button to clear the
Sampler.
9
• Or, by pushing the RVS/(CLR) button for
more than. 1 sec, you can clear Sampler.
ENGLISH
Adjust pitch
The Sampler playback pitch can be adjustable.
!1 Push the SAMP.PITCH/VOL. button, the pitch
input mode is set, PARAMETERS LED flashes
and the current settings are displayed on the
character display.
• Start Sampler playback.
!2 Turning the PARAMETERS knob can change
the pitch.
When pushing down and turning the
PARAMETERS knob, you can change the
pitch range 10 times faster.
Adjust sound level
The Sampler playback sound level can be adjustable.
!3 Push the SAMP.VOL button again when the
pitch input mode, the sound level input mode is
set, PARAMETERS LED flashes and the
current settings are displayed on the character
display.
• Start Sampler playback.
!4 Turning the PARAMETERS knob can change
the sound level.
!5 Push the SAMP.PITCH/VOL. button again to
turn the sound level input mode off.
17