Magnavox MDR868H Owner's Manual page 24

Network Connection
MDR868/867H
If you would like to proceed with the Network Connection
setting, perform this setting. If you would like to Skip this setting,
Select "No" using [ K/ L ], then press [ OK ]. Move on to ''fun-
Link (HDMI CEC)' screen will appear.' on page 25.
9
Select "Yes", then press [ OK ].
• Selecting "Yes" increases the Power Consumption
than Selecting "No", when the Power is Off in Standby
mode.
10
Select "Wired" or "Wireless" using [ K/ L ],
then press [ OK ].
If you connect this unit to the
Network using an Ethernet Cable,
Select "Wired" to Connect to the
Wired Internet.
Wireless
If you have a Wireless Router, Select
"Wireless" to Connect to the Internet.
For Wired Connection For Wired Connection
A
Connection test will Start automatically.
1. Select "Auto".After Connection test, the test result will
be Displayed. Press [ OK ].
• Please move on to 'Network Function' on page 25.
• If you Select "Manual", refer to 'Manual' on page 43.
For Wireless Connection For Wireless Connection
B
Select "Auto Scan", "Manual" or "Easy Connect" using [ K/ L ],
then press [ OK ].
This Setting automatically searches
for Wireless Networks.
Auto Scan
Select this Setting if you wish to
Manual
Configure the Wireless Networks
Easy Connect
manually.
Select this Setting if your Wireless
Router has a PBC button
easiest way to set up a Wireless
Connection. If it fails, try "Easy
Connect" again.
*1 PBC (Push Button Configuration) button may be the
Button's name that your Router uses. If not then refer
to the Router's Manual for more details.
*2 If it continuously fails, then refer to the Router's
Manual for more details.
"Auto Scan" Method
a
• AP (Access Point) List will appear.
1. Select an AP to which you would like to connect this
unit using [ K/ L ], then press [ OK ].
• If you Select an AP which does not support TKIP, a
Security Key Entry screen will appear. Enter the Security
Key using the On-screen Software Keyboard.
• Follow the On-screen Instructions.
• For details on how to use the Software Keyboard, refer
to 'Guide to the Software Keyboard' on page 25.
EN - 24
. It is the
*1
*2
2. After the Connection Test, the test result will be
Displayed.Press [ OK ].
• Please move on to 'Network Function' on page 25.
"Manual" Method
b
• SSID Input Screen will appear.
1. Enter the SSID using the On-screen Software Keyboard.
• Security mode Select screen will appear.
2. Select a Security mode :
"None" or "AES+TKIP" or "WEP" .
• Security Key Input Screen will appear.
3. Enter a Security Key using the On-screen Software
Keyboard.
• Connection test will Start automatically.
4. After the Connection test, the test result will be
Displayed. Press [ OK ].
5. Please move on to 'Unit Name' on page 25.
A
"Easy Connect" Method
c
Push Button Method
B
1. Select "Push Button Method".
2. Press the PBC button on your Wireless Router.
• Connection test will Start automatically.
3. After Connection test, the test result will be Displayed.
Press [ OK ].
• Please move on to 'Network Function' on page 25.
PIN Code Method
1. Select "PIN Code Method".
2. Select an AP to which you would like to Connect this
unit using [ K/ L ], then press [ OK ].
3. PIN Code will appear On-screen, then Input the Code
into AP.
• Refer to the Router's Manual for Inputting PIN Code.
• Connection test will Start automatically.
a
4. After Connection test, the test result will be Displayed.
Press [ OK ].
b • Please move on to 'Network Function' on page 25.
Note(s)
• "Easy Connect" method is only available when your
c
Wireless Router supports it. For details, please refer to
the Owner's Manual of your Wireless Router.
• If more than 64 AP's are found, a Confirmation message
will appear, then the Screen goes back to the AP List.
• Connection test will automatically Start when you Select
an AP that does not have an Authentication Method.