Alarm Settings; Using The Alarm Setup Menu - Panasonic WV-CW590G Operating Instructions Manual

Alarm settings

n Using the Alarm Setup Menu
Display the alarm setup menu from the setup menu to
configure alarm settings.
First, display the alarm setup menu.
1. Display the advanced setup menu (page 8), move
the cursor to ALARM
(SET) button.
This will display the alarm setup menu.
**ALARM SETUP**
VMD
PRESET ALM
ALARM IN/OUT
RET TOP
* The following sections numbered 1 to 3 explain
how to use each of the alarm setup menu items.
1 Motion Detector Setting (VMD)
1. Move the cursor to VMD, and then tilt the joystick
left or right to toggle it ON and OFF.
OFF : Turns off the motion detector.
MOTION DET : Alarm signal is output when motion is
SCENE CHANGE : Alarm signal is output when the
The factory default setting is OFF.
Motion Detector
The motion detector divides the screen into 48 blocks
and monitors changes in the luminance in each block.
When it detects any change (movement) in the image,
it outputs an alarm signal. When a change (movement)
in the image is detected while in the auto mode, the
alarm signal is output and the camera stops at the
preset position for a specified amount of time.
Important: Conditions for SCENE CHANGE
Monitoring might not be possible in the following situations.
• If only one part of the screen is not covered, or if the
covering is translucent
Also, false detection might occur in the following
situations.
• When extreme changes in lighting occur, such as
turning lights on an off
• If pedestrian or vehicle traffic is heavy
Note:
• If you want to set a motion detector for each preset
position, do the scene file setting (page 15).
• Added description that VMD does not move
during automatic operation (including pause)
22
, and then press the CAM
1
OFF
2
OFF
3
detected in the image. Selecting
MOTION DET and pressing the CAM
(SET) button displays the MOTION
DET setting menu, which can be
used for configuring detailed settings.
camera is covered by cloth, a
lid, spray paint or something.
l Configuring Detailed Motion Detector
Settings for MOTION DET
1. Move the cursor to MASK SET
the CAM (SET) button.
This will display the mask setting screen.
**MOTION DET**
LEVEL
DWELL TIME
DISPLAY MODE
ALARM
MASK SET
RECOVER TIME
RET TOP
2. Mask the areas of the screen that you do not want
the motion detector to monitor for movement.
To mask screen areas, use the same procedure as
step 5 under "SUPER-D6 (Super Dynamic 6)" on
page 9. After configuring mask settings, press the
MON (ESC) button to return to the motion detector
setting menu.
3. Move the cursor to ALARM, and then tilt the joystick
left or right to toggle demo mode (see step 5) alarm
output ON and OFF.
ON : Turns on alarm output in the demo mode.
OFF : Turns off alarm output in the demo mode.
The factory default setting is OFF.
4. Move the cursor to DISPLAY MODE, and then press
the CAM (SET) button.
This activates the demo mode.
Demo Mode
The demo mode divides the screen into 48 blocks and
monitors changes in the luminance in each block. It
also masks any part of the picture where there is a
change in average luminance that exceeds the
currently specified detection sensitivity level. The demo
mode results can be used to determine the optimum
detection sensitivity level (step 5) and the areas of the
screen that need to be masked (step 1).
5. Move the cursor to LEVEL, and then tilt the joystick
left or right to set the detection sensitivity level.
Shifting the setting towards the + side increases
sensitivity, while shifting towards the - side
decreases it. Repeat steps 4 and 5 until the
optimum sensitivity level is obtained.
Detection Conditions
: The moving object must be larger
Object Size
than one of the screen blocks (1/48
of the total screen area).
Subject Contrast : The contrast ratio between the
background and the moving object
m u s t b e a t l e a s t 5 % ( a t t h e
maximum LEVEL setting).
Object Speed : The allowable time range for the
object to pass from one edge of the
screen to the other is 0.1 second to
0.8 second. Movement that is faster or
slower than this cannot be detected.
, and then press
•••I•••131
- +
2S
OFF
OFF