Panasonic WV-CW590G Operating Instructions Manual page 17

Notes:
• The auto mode is exited automatically whenever
manual PAN/TILT or ZOOM/FOCUS is performed if
AUTOPAN is operating and PAN/TILT does SEQ,
SORT, PATROL, or AUTOTRACK movement. Note,
however, that that the contents of the setting menu
do not change. To return to the auto mode, open the
setup menu and then close it again. The auto mode
will also activate when the self return trigger time
(page 16) elapses.
• During operation, the lens may enter the refresh
mode.
• PATROL1-4 displays only the set number of
patrol routines (this page).
l Configuring AUTOPAN Detailed
Settings
1. Perform the following steps to set the PAN start
point and end point.
(1) Move the cursor to POSITION, press the CAM
(SET) button, and then move the cursor to
START.
(2) Use the joystick to move the camera to the
desired PAN start point, and then press the CAM
(SET) button.
This defines the start point and moves the
cursor to END.
(3) Use the joystick to move the camera to the
desired PAN end point, and then press the CAM
(SET) button.
This defines the start point and moves the
cursor to POSITION.
**AUTOPAN**
POSITION
SPEED
ENDLESS
DWELL TIME
PAN LIMIT
RET TOP
2. Move the cursor to SPEED and then tilt the joystick
left or right to select a panning speed setting.
Shifting the setting towards the "H" (right) side
increases the speed, while shifting towards the "L"
(left) side decreases it.
The factory default setting is 128.
3. Move the cursor to ENDLESS, and then tilt the joystick
left or right to turn endless panning on or off.
ON : Pans from the start point to the end point,
and then continues to pan in the same
direction from the end point to the start point.
Select OFF for the PAN LIMIT setting (step 5)
when using this setting. Panning will be
repeated endlessly.
OFF : Pans from the start point to the end point,
and then reverses direction to pan from the
end point to the start point. Panning is
repeated endlessly.
The factory default setting is OFF.
START
END
•••I•••128
L H
OFF
1S
OFF
4. Move the cursor to DWELL TIME, and then tilt the
joystick left or right to select the start point and end
point dwell time setting.
Tilting the joystick cycles through the stop time
display in the sequence shown below. (unit: sec)
The factory default setting is 1S.
0S ↔ 1S ↔ 2S ↔ 3S ↔ 5S ↔ 10S ↔ 20S ↔ 30S
5. Move the cursor to PAN LIMIT, and then tilt the
joystick left or right to toggle it ON and OFF.
ON : Limits manual panning to the zone between
the start point and the end point. The TILT
range is from horizontal to straight down.
Select OFF for the ENDLESS setting (step 3)
when using this setting.
OFF : Allows manual panning outside the zone
between the start point and the end point.
The factory default setting is OFF.
PAN LIMIT
PAN LIMIT allows panning in the area from the start
point to the end point specified in step 1, but not in the
area from the end point to the start point.
End point
AUTOPAN
zone
Start point
6 AUTOPAN Key Setting (AUTOPAN KEY)
Set the operations of the camera when AUTOPAN is
executed from the system controller. (page 16)
1. Move the cursor to AUTOPAN KEY, and then tilt the
joystick left or right to select a camera movement
mode setting.
Tilting the joystick cycles through settings in the
sequence shown below.
The factory default setting is AUTOPAN.
AUTOPAN ↔ SEQ ↔ SORT ↔ PATROL1 ↔ PATROL2
AUTOTRACK ↔ PATROL4 ↔ PATROL3
Notes:
• Auto Mode can be started, but not stopped, with
the AUTOPAN key.
• PATROL1-4 displays only the set number of patrol
routines (this page).
7 Patrol Function Setting (PATROL)
The patrol function remembers manual operations for
later automatic playback when they are needed.
1. Aim the camera, with the menu closed, at the start
point of the routine you want it to remember.
2. Move the cursor to NUMBER, and then tilt the joystick
left or right to specify the number of patrol routines.
Tilting the joystick cycles through settings in the
sequence shown below. The amount of storage
time available depends on the number of routines.
The storage time display changes in the sequence
shown below. (unit: sec, min)
The factory default setting is 1 (2 MIN).
Camera
PAN LIMIT
zone
17