Sharp AL-2051 Service Manual page 113

Program
Program name
number
16 KEY TOUCH SOUND
17 SOUND AT DEFAULT
18 TONER SAVE MODE
19 AE LEVEL ADJUST
20 LANGUAGE
21 RESET FACTORY
22 SORT AUTO SELECT
24 CHECK RSPF OPEN
25 VALID COPY WIDTH
28 LSU SETTING
29 PAPER TYPE
30 DISPLAY CONTRAST
Print mode
Program
Program name
number
1 FORCED OUTPUT
2 USB 2.0 MODE
SWITCH *
3 AUTO TRAY SWITCH
4 ENABLE TCP/IP
5 ENABLE DHCP
6 IP ADDRESS SETTING
* The scanning speed increases when the USB 2.0 mode is set to "HI-SPEED", however, the printing speed does not increase considerably.
Setting codes
(factory default setting
appears in bold)
1: LOW • This sets the volume of beep signals.
2: HIGH
3: OFF
1: ON • Use this to sound a beep when a base setting is selected.
2: OFF
1: ON • This mode reduces toner usage by about 10% when copying. Toner save
2: OFF mode is effective when the exposure mode is AUTO or TEXT.
1: SPF/RSPF • This is used to adjust the exposure level.
(Adjustment to 5
• The automatic exposure level can be adjusted separately for the docu-
levels is possible)
ment glass and the RSPF.
2: DOCUMENT GLASS
• The factory default setting for the exposure level is "center".
(Adjustment to 5
levels is possible)
1: AMERICAN This is used to set the language used in the display.
ENGLISH 18 Languages can be selected.
2: ENGLISH
3: FRENCH
4: SPANISH
5: GERMAN
6. ------
:
18: Brazilian portuguese
1: Yes This is used to return all settings to the factory default settings.
2: No
1: ON Use this setting to enable or disable sort auto select mode.
2: OFF
1: ON • You can set the operation that takes place if the [START] key (
2: OFF pressed when the RSPF is not completely closed.
1: A4 • Set the allowed paper sizes for copying from the bypass tray. When "B5"
2: B5 is selected, a copy of a letter size original will only be printed up to invoice
size.
1: ON • Select whether copying is only allowed when the polygon motor is rotat-
2: OFF ing, or also when the polygon motor is stopped.
1: PLAIN PAPER • Set the temperature of the fusing unit when the bypass tray is used. Nor-
2: HEAVY PAPER mally "PLAIN PAPER" should be selected.
1: LIGHTER • Set the contrast of the display.
2: LIGHT
3: NORMAL
4: DARK
5: DARKER
Setting codes
(factory default setting
appears in bold)
1: ON When this function is enabled, printing in printer mode will automatically
2: OFF continue using a different size of paper if the specified size of paper runs out
in all trays. This feature does not function in copy mode.
1: FULL-SPEED This sets the USB 2.0 data transfer speed. To obtain the fastest speed when
2: HI-SPEED using the USB 2.0 connector, first verify that your computer meets the
system requirements (operating system and driver), and then use this
program to change the USB 2.0 mode to "Hi-Speed". Note that the setting
should not be changed while running a TWAIN driver.
1: ON This is selectable when the optional paper tray is installed.
2: OFF (This is not shown when the optional tray is not installed.)
1: ON This is to select whether or not to make the network connection by TCP/IP
2: OFF protocol effective.
1: ON This is to select whether or not to apply to DHCP network connection.
2: OFF
1: IP ADDRESS This is to set IP address, Subnetmask and Default Gateway from the
2: SUBNETMASK machine. This can also be used to check the machine's IP ADDRESS when
3: DEFAULT GATEWAY "IP ADDRESS" is selected. When the program number 4 "ENABLE DHCP"
is "ON" and the machine is under DHCP environment, the IP address on the
display is shown with "
AL-2051 USER PROGRAM 11 - 2
Explanation
Explanation
" at the tail end.
) is