Fujitsu fi-4860C Consumable Replacement And Cleaning Instructions
Hide thumbs
Also See for fi-4860C:
- Operator's manual (321 pages) ,
- Installation manual (88 pages) ,
- Installation procedures (3 pages)
Related Manuals for Fujitsu fi-4860C
Summary of Contents for Fujitsu fi-4860C
- Page 1 C ONSUMABLE EPLACEMENT AND LEANING NSTRUCTIONS fi-4860C C ONSUMABLE EPLACEMENT LEANING NSTRUCTIONS CG00000-715401B...
- Page 2 C ONSUMABLE EPLACEMENT AND LEANING NSTRUCTIONS ONSUMABLES Description Life Fujitsu P/N Lamp 1000 PA83950-0290 Brake Roller 300,000 CA04315-F705 Pick Roller Unit 300,000 PA03296-F711 300,000 CA04315-G730 1 - Front Side and Back Side Lamps 2 - Lamp Life Rated in Scanning Hours...
- Page 3 C ONSUMABLE EPLACEMENT AND LEANING NSTRUCTIONS EPLACING THE RONT A defective or improperly installed Front Side Lamp can cause the “Front Side Optical Alarm” message to be displayed on the Operator Panel of the scanner. Vertical lines or bad image quality on the front side scan can also be caused by a defective Front Side Lamp.
- Page 4 C ONSUMABLE EPLACEMENT AND LEANING NSTRUCTIONS EPLACING THE RONT CONT • Rotate the Lamp a half turn so that the terminals on each end align with the slot on the Lamp Socket and remove the Lamp from the unit.
- Page 5 C ONSUMABLE EPLACEMENT AND LEANING NSTRUCTIONS EPLACING THE A defective or improperly installed Back Side Lamp can cause the “Back Side Optical Alarm” message to be displayed on the Operator Panel of the scanner. Vertical lines or bad image quality on the back scan can also be caused by a defective Back Side Lamp.
- Page 6 C ONSUMABLE EPLACEMENT AND LEANING NSTRUCTIONS EPLACING THE CONT Note: Make sure the clear area of the Lamp faces up. If the lamp is installed with the clear area facing the incorrect direction (down), a Back Side Optical Alarm will occur.
- Page 7 C ONSUMABLE EPLACEMENT AND LEANING NSTRUCTIONS EPLACING THE OLLER A worn out, defective, or improperly installed Pick Roller Unit will cause misfeeds and paper jams. It can also cause the “Pick roller unit not set” message to be displayed on the Operator Panel of the scanner. The Pick Roller Unit has an approximate life of 300,000 pages.
- Page 8 C ONSUMABLE EPLACEMENT AND LEANING NSTRUCTIONS EPLACING THE OLLER CONT Pick Roller Unit • To replace, engage the drive ring on the left side of the Pick Roller Unit onto the drive shaft on the Sheet Guide Assembly. Ring •...
- Page 9 C ONSUMABLE EPLACEMENT AND LEANING NSTRUCTIONS EPLACING THE RAKE OLLER A worn out or improperly installed Brake Roller will cause multiple feeds and paper jams, or will display the “Separation roller worn” message on the Operator Panel of the scanner. An improperly installed Brake Roller may cause the “Break roller not set”...
- Page 10 C ONSUMABLE EPLACEMENT AND LEANING NSTRUCTIONS EPLACING THE RAKE OLLER CONT • Hold the lever on the Brake Roller and turn it up and pull Brake Roller the Brake Roller out of the scanner. • Take a new Brake Roller and...
-
Page 11: Replacing The Pad
C ONSUMABLE EPLACEMENT AND LEANING NSTRUCTIONS EPLACING THE Multiple feeds and misfeeds can be caused by a worn or improperly installed Pad. The life span of the Pad Assembly is approximately 300,000 pages. If NCR or carbonless paper is used the life span of the Pad may be decreased by half. - Page 12 C ONSUMABLE EPLACEMENT AND LEANING NSTRUCTIONS EPLACING THE CONT Pad Assembly Mounted on Guide Plate • Press the rolled tab on the back of the Guide Plate to remove the Pad Assembly. Rolled Tab Hooks • Align the hooks on the top of...
- Page 13 C ONSUMABLE EPLACEMENT AND LEANING NSTRUCTIONS EPLACING THE ISCHARGE RUSHES There are two Discharge Brushes in the ADF area of the scanner. These brushes remove paper dust and other contaminents from the Pick Roller Unit and the Brake Roller. Replacing these brushes and keeping them in good condition will increase the life of both the Pick roller Unit and Brake Roller.
- Page 14 C ONSUMABLE EPLACEMENT AND LEANING NSTRUCTIONS EPLACING THE ISCHARGE RUSHES CONT OWER ISCHARGE RUSH • Remove the Pick Roller Unit. Guide Plate • Remove the Guide Plate by pressing down on the upper part with your fingers at two positions.
- Page 15 C ONSUMABLE EPLACEMENT AND LEANING NSTRUCTIONS LEANING OCATIONS AND REQUENCIES Location Tools Frequency Pick Rollers/Brake Roller Cleaning Sheets Every 50,000 Sheets Pad/Upper Feed Rollers Cloth & Isopropyl Alcohol Every 100,000 Sheets Metal Feed Rollers Cloth and F2 Cleaner Every 100,000 Sheets Transport Path Cloth &...
- Page 16 C ONSUMABLE EPLACEMENT AND LEANING NSTRUCTIONS LEANING THE OLLERS WITH THE LEANING HEETS The cleaning sheets are designed to remove only loose paper dust and ink from the rollers. Use them approximately every 50,000 sheets scanned. They are to be used in between the thorough cleanings of the scanner.
- Page 17 C ONSUMABLE EPLACEMENT AND LEANING NSTRUCTIONS LEANING THE OLLERS WITH THE LEANING HEETS CONT • Remove the protective paper from the cleaning sheet. Cleaning Protective Sheet Paper • Place the cleaning sheet on the Hopper against the Left Hopper Guide, adhesive side up to clean the Upper Transport Path.
- Page 18 C ONSUMABLE EPLACEMENT AND LEANING NSTRUCTIONS LEANING THE ELATED ONSUMABLES It is very important to clean the scanner feed consumables on a regular basis to avoid paper feeding problems. These items should be cleaned at least every 100,000 sheets. Daily cleaning may be required if carbon- less paper or paper with large amounts of toner and ink are fed.
- Page 19 C ONSUMABLE EPLACEMENT AND LEANING NSTRUCTIONS LEANING THE ELATED ONSUMABLES CONT LEANING THE RAKE OLLER • Remove the Brake Roller. • Wipe the rubber area of the Brake Roller using a lint free cloth moistened with F1 Cleaner. •...
- Page 20 C ONSUMABLE EPLACEMENT AND LEANING NSTRUCTIONS LEANING THE OLLERS It is very important to clean the scanner Pinch Rollers on a regular basis to avoid paper feeding problems. These items should be cleaned at least every 100,000 sheets. Daily cleaning may be required if carbonless paper or paper with large amounts of toner and ink are fed.
- Page 21 C ONSUMABLE EPLACEMENT AND LEANING NSTRUCTIONS LEANING THE OLLERS CONT ETAL OLLERS OWER • Wipe the Metal Feed Rollers thoroughly using a lint free cloth moistened with F2 Cleaner. Note: If the rollers have a heavy build up of toner and ink, allow the F2 Cleaner to soak on the rollers prior to wiping.
- Page 22 C ONSUMABLE EPLACEMENT AND LEANING NSTRUCTIONS LEANING THE RANSPORT Lever • Lift the Lever at the right to open the Upper Transport Unit. • Wipe the Upper and Lower Transport Paths (metal sheet guides between rollers) with a dry cloth or a cloth soaked in F1 Cleaner or isopropyl alcohol.
- Page 23 C ONSUMABLE EPLACEMENT AND LEANING NSTRUCTIONS LEANING THE ISCHARGE RUSHES Dirty Discharge Brushes can cause multiple feeding and jamming. Keeping the Discharge Brushes clean will extend the life of the Pick Roller Unit and the Brake Roller. Clean the brushes when they are covered in paper dust or toner.
- Page 24 C ONSUMABLE EPLACEMENT AND LEANING NSTRUCTIONS LEANING THE LASS URFACES ON THE HEET UIDES Dirty Glass Surfaces can cause vertical streaks in the scanned image. OWER HEET UIDE ACKSIDE MAGE Lever • Lift the Lever at the right to open the Upper Transport Unit.
- Page 25 C ONSUMABLE EPLACEMENT AND LEANING NSTRUCTIONS LEANING THE LASS URFACES ON THE HEET UIDES CONT PPER HEET UIDE RONTSIDE MAGE • Push down on the Glass Sheet Guide tab to open. Glass Sheet Guide • Wipe both sides of the glass...
- Page 26 C ONSUMABLE EPLACEMENT AND LEANING NSTRUCTIONS LEANING THE ENSORS Clean the Document Width and Jam Sensors if the “Sensor dirty” or “Sensor error” messages are displayed on the Operator Panel of the scanner. SF1 S ENSOR Lever • Lift the Lever at the right to open the Upper Transport Unit.
- Page 27 C ONSUMABLE EPLACEMENT AND LEANING NSTRUCTIONS LEANING THE ENSORS CONT SA3, SA4, SB4, SB5, SSK1,SSK2 S ENSORS Document Width Sensors (6 Locations) • Clean the six sensors with a dry cloth or a cloth moistened with F1 Cleaner or isopropyl alcohol if necessary.
- Page 28 C ONSUMABLE EPLACEMENT AND LEANING NSTRUCTIONS LEANING THE AMPS Dirty lamps can cause vertical streaking or other image quality problems. RONT Lever • Lift the Lever at the right to open the Upper Transport Unit.. • Remove the Front Side Lamp.
- Page 29 C ONSUMABLE EPLACEMENT AND LEANING NSTRUCTIONS LEANING THE AMPS CONT • Push the Blue Locking Tab back and pull open the side cover. The cover is on the left side of the scanner. • Hold the Blue handle and pull out the Back Side Lamp Unit.
- Page 30 C ONSUMABLE EPLACEMENT AND LEANING NSTRUCTIONS...