Download Print this page

Fujitsu FI-4120C Installation Procedures Manual

Scsi scanner installation procedures for windows nt 4.0.
Hide thumbs
   

Advertisement

Fujitsu SCSI Scanner Installation Procedures
If you are installing the following models by means of the SCSI interface then use this
document.
SP10C
SP15C
SP600C
SP620C
SP3091DC
SP3092DC
SP93GX
If you are going to use the USB interface of a dual SCSI/USB model then use the USB scanner
installation guide. For Scansnap models please use the Scansnap installation guide.
Hardware requirements.
You will need a PC system that meets our recommended specifications, an appropriate SCSI
controller, and a SCSI cable (six foot recommended maximum). For recommended PC system
specifications and SCSI controllers please reference the
You may also need your Operating System Disk.
Step A: Installing the SCSI Host Adapter (Adaptec).
1. Shut down your PC and remove the case cover.
2. Locate a free PCI slot and remove the back plate if necessary.
3. Install the SCSI controller in an open PCI slot.
Make sure that the card is seated completely in the slot and secured in the frame
Warning! Failure to secure the SCSI controller in the PC can result in damage to the
SCSI card, scanner, and/or your system.
4. Boot your PC without the scanner attached
Step B: Installing the SCSI drivers (Adaptec).
Although Windows NT has driver support for your host adapter it does not support plug and
play. Therefore the SCSI drivers will need to be loaded manually. Follow the instruction below
to install the driver for your host adapter.
Rev051906A
Windows NT 4.0
M3093GX\DG
M3096GX
M3097G\G+\DG
M3099G\GX\GH
FI-4120C\C2
Fi-4220C\C2
Fi-4340C
Fi-4530C
Fi-4640S
M4097D
Fi-4750C\L
M4099D
Fi-4860C
Fi-4990C
Scanner Hardware Reference
.
Fi-5120C
Fi-5220C
Fi-5530C
Fi-5650C
Fi-5750C
Fi-5900C
page.
Page 1 of 9

Advertisement

   Related Manuals for Fujitsu FI-4120C

   Summary of Contents for Fujitsu FI-4120C

  • Page 1

    Fi-4220C\C2 SP93GX Fi-4340C If you are going to use the USB interface of a dual SCSI/USB model then use the USB scanner installation guide. For Scansnap models please use the Scansnap installation guide. Hardware requirements. You will need a PC system that meets our recommended specifications, an appropriate SCSI controller, and a SCSI cable (six foot recommended maximum).

  • Page 2

    Fujitsu SCSI Scanner Installation Procedures Windows NT 4.0 1. Login with administrator rights. 2. Go to Start, Control Panel, SCSI Adapters. 3. Then click on the Drivers tab and click ‘Add.’ 4. Next select ‘Adaptec’ under Manufacturers 5. On the next menu scroll down again and double click on the line that reads –...

  • Page 3

    Fujitsu SCSI Scanner Installation Procedures 6. Insert your WinNT CD system disk and click OK. 7. When prompted to reboot, select no. 8. Then go to www.adaptec.com, and click on the “search” tab. Scroll down to the “Enter key word or quoted phrase” box and type in “aspi32.exe.”...

  • Page 4

    “aic78xx” should not be sharing its IRQ with any other devices in the system. Step C: Installing the drivers from the Setup CD. To begin it is recommended that you install the drivers first before connecting the scanner. Installing the ASPI-Twain driver.

  • Page 5

    WinZip* self-extractor box will popup. Click on browse and select the Fujitsu Downloads folder, then click on Extract. The file will begin to unzip and when finished a message box will report the number of files unzipped. Click on OK and close WinZip.

  • Page 6

    4. Afterwards click on ISIS Software Drivers. 5. Scroll down the list of scanner models in the left column and select the appropriate ISIS driver to the right of your scanner model. 6. Double click on the driver file name and the File Download box will popup.

  • Page 7

    If your model scanner does not have a flatbed then proceed to Step F. The flatbed model scanners typically include a lock on the flatbed designed to protect the scanner during shipment. Before the scanner can be used the shipping lock must be unlocked. To unlock it do the following: 1.

  • Page 8

    SCSI host adapter. Next if the scanner is the last device (only device) on the SCSI chain then it must be terminated. If the scanner is not the last device on the SCSI chain, then the terminator should be removed or turned off before connecting it to the next SCSI device.

  • Page 9

    Congratulations! You have successfully completed and tested your scanner installation. Step H: Installing third party software applications. After you have successfully installed all the Fujitsu software and hardware, then it is time to install any additional third party scanning software that you wish to use. Please follow the software manufacturer’s instructions for installation.

Comments to this Manuals

Symbols: 0
Latest comments: