Related Manuals for E-Wheels EW-18
Summary of Contents for E-Wheels EW-18
- Page 1 EW-18 OWNER'S MANUAL Electric Wheels LLC-888-571-2845 (Toll Free)- 15855 N Greenway Hayden Loop -Suite 190, Scottsdale, AZ 85260...
- Page 2 WARNING THE ELECTRIC TRISCOOTER IS NOT A TOY AND SHOULD NOT BE OPERATED BY ANY ONE UNDER 12 YEARS OLD. Safety Instruction (Please take note of the followings before each ride) • The maximum weight capacity is 300 lbs. • Only one person at a time should ride. •...
- Page 3 6. 5mm Allen Wrench 1. Remove the EW-18 from it's carton. Start by using the box cutter to cut the banding straps . Once the banding straps are cut, carefully cut the tape around the box and start removing all the bubble wrap .
- Page 4 Please make sure to have the contents listed below and as shown in picture above. 1. Hub Motor 2. Tool Kit 3. Brake Spring 4. Seat Clamp ( 2 pieces) 5. Charger 6. Front Fender 7. Bottom Handle Bar 8. Front Fork 9.
- Page 5 1. Using the 15mm and 14mm wrenches , loosen up the nut from the bolt.(figure 1) 2. Once you have removed the nut and bolt , Insert the front fork and attach into the scooter platform.(figure 2) 3. After you have attached the fork into the platform, Insert the bolts back in and secure with the nut .(figure2) Electric Wheels LLC-888-571-2845 (Toll Free)- 15855 N Greenway Hayden Loop -Suite 190, Scottsdale, AZ 85260...
-
Page 6: Handlebar Installation
HANDLE BAR INSTALLATION 1. First step will be to grab the bottom handle bar part and insert it on the top of the fork.(figure 1) 2. Once you have place the part into the front fork, you will use the 6mm Allen Wrench to secure the part into place. Make sure you have the handle bar straight before tightening the bolt .(figure1) 3. - Page 7 Front Hub Motor Installation 1. Place the Hub Motor into the front fork. Make sure that the side with the brake hub has the washers and nut in the following sequence: Washer-Fork-Lock Washer-Washer-Nut.(Figure 1) The other side of the hub must have the Following sequence: Washer-Spacer-Fork-Washer-Nut.
- Page 8 3. Once we have the Hub Motor and Brake Hub in place tighten up the axle nuts and the brake hub screw. 4. Insert the brake cable through the cable holder and the adjusting nut. Make sure you have the brake spring between the cable holder and the adjusting nut.(Figure 1) 5.Plug the hub motor cable.
-
Page 9: Seat Installation
Seat installation 1. Place the seat clamps at each end of seat post .(Figure 1) 2 . Insert seat post into the scooter platform .(Figure 2) 3. Insert seat into seat post.(Figure 3) Electric Wheels LLC-888-571-2845 (Toll Free)- 15855 N Greenway Hayden Loop -Suite 190, Scottsdale, AZ 85260... -
Page 10: Charging The Battery
Connect the battery and charger using the charger convertible cable. Plug the charger into the wall outlet. RIDING THE EW-18 Once you have completed the initial charge you are ready to ride. Remember, this is not a toy. The tri scooter can reach speeds up to 15.5 mph depending on the terrain and the weight of the rider. - Page 11 Electric Wheels LLC-888-571-2845 (Toll Free)- 15855 N Greenway Hayden Loop -Suite 190, Scottsdale, AZ 85260...
-
Page 12: Warranty
Six (6) months from the date of purchase, if any part or electronic component of the Scooter is found upon examination to be defective in material and/or workmanship, it will be repaired or replaced, at E-Wheels, LLC’s option, without charge. Labor charges are NOT included. The purchaser is responsible for the delivery to the authorized repair facility. - Page 13 • Used other than for the purpose of the purchaser’s mobility. • Repairs and/or modifications made to any part of the scooter without specific and prior consent from E-Wheels, LLC. • Labor, service calls, shipping, and other charges incurred for repair of the product not approved by E-Wheels, LLC.