Table of Contents
Related Manuals for Dremel 800-49
Summary of Contents for Dremel 800-49
- Page 1 DM 2610945859 05-07 7/10/07 8:43 AM Page 1 IMPORTANT: Read Before Using Operating/Safety Instructions 800-49 his symbol refers to the EMC requirements of the Australian Standards Australia 1300 30 70 44 New Zealand 0800 54 33 53 www.dremel.com...
-
Page 2: General Safety Rules For All Battery Operated Tools
DM 2610945859 05-07 7/10/07 8:43 AM Page 2 General Safety Rules for All Battery Operated Tools Read and understand all instructions. Failure to follow all instructions listed WARNING below, may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS Work Area balance enable better control of the tool in unexpected situations. - Page 3 DM 2610945859 05-07 7/10/07 8:43 AM Page 3 only accessories that maintenance performed by unqualified recommended by the manufacturer for your personnel may result in a risk of injury. model. Accessories that may be suitable for When servicing a tool, use only identical one tool may create a risk of injury when used replacement parts.
- Page 4 DM 2610945859 05-07 7/10/07 8:43 AM Page 4 Use clamps to support workpiece Do not allow familiarity gained from whenever practical. Never hold a small frequent use of your rotary tool to become workpiece in one hand and the tool in the commonplace.
-
Page 5: Battery Care
Description and Specifications. Other types of Use of an attachment not recommended or batteries may burst causing personal injury sold by Dremel may result in a risk of fire, and damage. electric shock or injury to persons. Charge battery pack in temperatures above... -
Page 6: Functional Description And Specifications
BATTERY PACK RELEASE HANGER ALIGNMENT ARROWS INDICATOR LIGHT CHARGER Rotary Tool Model number 800-49 Voltage rating 10.8 V No load speed 5,000-35,000/min Collet Capacities 0,8 mm, 1,6 mm, 2,4 mm, 3,2 mm Charger Model number 856-02 Voltage rating 230-240 V... - Page 7 DM 2610945859 05-07 7/10/07 8:43 AM Page 7 Assembly Disconnect battery pack shaft. Always use the collet which matches WARNING from tool before making the shank size of the accessory you plan any assembly, adjustments or changing to use. Never force a larger diameter shank accessories.
- Page 8 DM 2610945859 05-07 7/10/07 8:43 AM Page 8 router bits, and cutting wheels. Accessories guide it. In the low speed tools, you not only come in a variety of shapes and permit you to guide the tool, but also apply pressure to it, as do a number of different jobs.
- Page 9 Check for voltage at outlet by plugging in some other electrical device. Note: Use of chargers or battery packs not sold by Dremel may void the warranty. USING THE CORDLESS ROTARY TOOL Instead, lower the spinning accessory lightly to...
- Page 10 DM 2610945859 05-07 7/10/07 8:43 AM Page 10 Operating Speeds For Accessories Set the speed indicator to fit the job to You can refer to the charts on page 12, 13, achieve the best job results when working and 14 to determine the proper speed, based with differentmaterials.
-
Page 11: Speed Settings
A few older attachments, such as Speed Settings Use only Dremel™ tested, high performance accessories. * Speed for light cuts; Caution - burning on deep grooves. • Depending on cutting direction relative to grain. High Speed Cutters... - Page 12 DM 2610945859 05-07 7/10/07 8:43 AM Page 12 Speed Settings (Continued) Use only Dremel™ tested, high performance accessories. * Speed for light cuts; Caution - burning on deep grooves. • Depending on cutting direction relative to grain. Tungsten Carbide Cutters Catalog...
- Page 13 DM 2610945859 05-07 7/10/07 8:43 AM Page 13 Use only Dremel™ tested, high performance accessories. * Speed for light cuts; Caution - burning on deep grooves. • Depending on cutting direction relative to grain. Cutting Accessories Catalog Soft Hard Laminates...
-
Page 14: Maintenance
Always could cause serious hazard. We recommend wear safety goggles when cleaning tools that all tool service be performed by a Dremel with compressed air. Service Center. SERVICEMEN: Disconnect Ventilation openings and switch levers must be tool and/or charger from power source before kept clean and free of foreign matter. - Page 15 DM 2610945859 05-07 7/10/07 8:43 AM Page 15 Dremel Accessories (Cont.) Mandrels A mandrel is a shank with a threaded or screw Small Screw Mandrel No. 402 head, which are required when you use polishing accessories, cutting wheels, sanding This is a mandrel with a small screw at its tip, discs, and polishing points.
- Page 16 DM 2610945859 05-07 7/10/07 8:43 AM Page 16 Dremel Accessories (Cont.) Silicon Carbide Grinding Stones Bristle Brushes (blue/green) These are excellent cleaning tools on Tougher than aluminum oxide points, these silverware, jewelry and antiques. The three are made especially for use on hard materials shapes make it possible to get into tight such as glass and ceramics.
- Page 17 3,2 mm shank. High Speed Router Bits For routing, inlaying, and mortising in wood and other soft materials. Use with Dremel No. Grinding Wheel 330 Router attachment and No. 231 Use for deburring, removing rust, and general Shaper/Router table.
- Page 18 DM 2610945859 05-07 7/10/07 8:43 AM Page 18 Mandrel No. 401 is used with the felt down straight on the screw Mandrel, and be polishing tip and wheels. Thread the tip on to turned all the way to the collar. the screw carefully.
- Page 19 DM 2610945859 05-07 7/10/07 8:43 AM Page 19 To replace a band on the Drum Sander, Before each use, check to WARNING make certain that all loosen the screw without removing it to components are assembled to accessory contract the drum then slide the old band off. Slide the new sanding band on and then shank and that the drum is sufficiently expand the drum by tightening the screw...
- Page 20 DM 2610945859 05-07 7/10/07 8:43 AM Page 20 MODEL 800-49 CODE PART DESCRIPTION 2610919750 Motor Assembly 2610919742 Speed Control Assembly 2914201664 Screw (4 Required) 2610919753 Lock Button 2615297355 Collet Nut 2615110480 3.2 mm Collet (In Tool) 2610919754 Housing Cap 2610944356...
Need help?
Do you have a question about the 800-49 and is the answer not in the manual?
Questions and answers