Advertisement
Quick Links
Advertisement
Related Manuals for Arecont Vision MegaDome AV1355DN-1HK
Summary of Contents for Arecont Vision MegaDome AV1355DN-1HK
- Page 1 ® Arecont Vision MegaDome Installation Manual 0 | P a g e...
- Page 2 ® Arecont Vision MegaDome Installation Manual ® MegaDome Installation Manual Inside the box: Mounting the Camera: ® Arecont Vision MegaDome Remove camera and hardware from the Mounting template box. C. Magnetic core Using the Mounting template, prepare the D. Pack of four (4) wood screws and four (4)
- Page 3 ® Arecont Vision MegaDome Installation Manual Run Ethernet cable through the hole on the bottom of the camera (Image 3) and plug it into the RJ45 port. NOTE: If the camera will be powered via PoE, please skip to step 6.
- Page 4 ® Arecont Vision MegaDome Installation Manual Reference Image 5 for proper positioning of Adjusting the Tilt, Pan, Z-axis (yaw) and Focus: the magnetic core. To adjust the tilt, use a #1 Phillips screwdriver If you are using the side conduit opening,...
- Page 5 ® Arecont Vision MegaDome Installation Manual To adjust back focus, loosen the two (2) set screws with the appropriate Allen key as shown Image 8 (only one of two screw holes shown). Adjust the silver back focus ring as needed and tighten down the set screws.
-
Page 6: Installation Best Practices
® Arecont Vision MegaDome Installation Manual Installation Best Practices Adding Teflon thread sealing Wind Vinyl electrical Begin Installation tape on all cables tape to all male threads Connect ¾” NPT conduit pipe to junction box adapter Make sure position of conduit... - Page 7 ® Arecont Vision MegaDome Installation Manual ® MegaDome Pendant Mount (MD-CMT) Installation Instructions Inside the box: Top shield Pendant Mount C. Mounting template D. Pack of four (4) machine screws Pack of four (4) small machine screws Pack of four (4) wood screws and four (4)
- Page 8 ® Arecont Vision MegaDome Installation Manual ® MegaDome Wall Mount (MD-WMT2) Installation Instructions Inside the box: Remove Wall Mount and hardware from the box. Wall mount Top shield C. Mounting template D. One double sided hex key Pack of four (4) machine screws...
- Page 9 ® Arecont Vision MegaDome Installation Manual ® MegaDome Wall Mount Cap (MD-CAP) Installation Instructions Inside the box: Wall Mount Cap (MD-CAP) Pack of four (4) machine screws MD-CAP Not included but needed: 1½” NPT Pipe nipple 1 ½” Coupling ...
- Page 10 ® Arecont Vision MegaDome Installation Manual ® MegaDome Junction Box Adapter (MD-JBA) Installation Instructions Inside the box: Junction Box Adapter Pack of four (4) machine screws C. Pack of four (4) wood screws and four (4) dry wall anchors D. Large round rubber gasket...
- Page 11 ® Arecont Vision MegaDome Installation Manual ® MegaDome Flush Mount Adapter (MD-FMA) Installation Instructions Screw the “lever screws” until the FMA is Inside the box: snuggly installed, as shown in Image 21. The Flush Mount Adapter “Support Arm” will ride down the screw to G.
- Page 12 ® Arecont Vision MegaDome Installation Manual ® MegaDome Electrical Box Adapter (MD-EBA) Installation Instructions Inside the box: Electrical Box Adapter Pack of four (4) machine screws Not included but needed: #2 Phillips head screw driver Common Electrical Box, such as single gang box, double gang box or square electrical box.
- Page 13 ® Arecont Vision MegaDome Installation Manual ® MegaDome Pole Mount Adapter (AV-PMA) Installation Instructions Inside the box: Pole Mount Adapter Run the Ethernet cable and outside power 2x Small Steel Straps cable (if necessary) through the Junction Box C. 2x Large Steel Straps Adapter and MegaDome®...
- Page 14 ® Arecont Vision MegaDome Installation Manual ® MegaDome Corner Mount Adapter (AV-CRMA) Installation Instructions Inside the box: NOTE: Use silicon or water pipe seal tape to make sure no water leakage between conduit Corner Mount Adapter pipe and junction box adapter.
- Page 15 ® Arecont Vision MegaDome Installation Manual ® MegaDome I/O Cable Connection Inside the box: connector as shown in image 33. NOTE: The connection is a little stiff so be sure to apply I/O Cable enough pressure to connect it; using a flat...
- Page 16 ® Arecont Vision MegaDome Installation Manual Image 33 Image 33.1 Image 33.2 Connect Here Do NOT Connect Here 14 | P a g e...
- Page 17 ® Arecont Vision MegaDome Installation Manual ® MegaDome Heater Accessory Inside the box: Screw the heater board to the standoffs as shown in Image 36. Heater Two (2) screws Not included but needed: #1 Phillips head screw driver Image 35...
- Page 18 ® Arecont Vision MegaDome Installation Manual ® MegaDome Focus Tool Accessory Inside the box: Focus Tool NOTE: Focus Tool is a small piece of bubble which has same material and property as bubble’s, including thickness, curvature and other optical performance.
- Page 19 ® Arecont Vision MegaDome Installation Manual 17 | P a g e...