Thx ultra2 digital / thx select dolby digital ex /dts es / dolby digital surround receiver, progressive scan universal disc player, system control, 3 chip dlp high definition projector, hd ready plasma monitor, reference control preamplifier/power amplifi (39 pages)
Av receivers / remotes/tuners / home system / multi-zone control amplifier / plasma display / dlp projectors / stereo receiver / power amplifiers / multi-channel super audio cd player / cd player / integrated amplifier / stereo tuner / high definition dig (36 pages)
Page 1
Model PM-11S1 User Guide Integrated Amplifier...
Page 2
Su recibo de compra es su prueba permanente de haber adquirido un aparato de valor, Este recibo deberá guardarlo en un lugar seguro y utilizarlo como referencia cuando tenga que hacer uso del seguro o se ponga en contacto con Marantz. IMPORTANTE Cuando solicite el servicio otorgado por la garantia el usuario tiene la responsabilidad de demonstrar cuándo efectuó...
Page 3
The PM-11S1 is in conformity with the EMC directive and low-voltage directive. Français Le PM-11S1 est conforme à la directive EMC et à la directive sur les basses tensions. Deutsch Das Modell PM-11S1 entspricht den EMC-Richtlinien und den Richtlinien für Niederspannungsgeräte.
Page 4
Español ADVERTENCIAS - No exponga el equipo a la lluvia ni a la humedad. - No extraiga la tapa del equipo. - No introduzca nada en el interior del equipo a través de los orificios de ventilación. - No maneje el cable de alimentación con las manos mojadas. - No cubra la ventilación con objetos como manteles, periódicos, cortinas, etc.
7 7 7 7 7 EQUIPMENT MAINS WORKING SETTING Your Marantz product has been prepared to comply with the household power and safety requirements that exist in your area. PM-11S1 can be powered by 230V AC only.
• Display SA2, these lin- The PM-11S1 adopts an LCD to display input source and vol- ume level. Compared to other types of display panels, an LCD generates less drive noise and radiated noise, hence the ef- fect on sound quality is minimal.
POWER ON/OFF PHONES SPEAKER 7 7 7 7 7 Keep Objects Off Keep objects off the PM-11S1. Blocking the vent can result in accident and damage. 7 7 7 7 7 Do Not Touch Hot Spots During and Immediately After Use During and immediately after use, the PM-11S1 is hot in ar- eas other than the controls and rear panel connection jacks.
COLD 2.In Europe COLD e The PM-11S1 adopts the USA circuitry. If the PM-11S1 is connected via a balanced cable to a preamplifier or control amplifier of European circuitry, signal phases will be re- versed. To correctly align signal phases, switch the w and e pins of one of the XLR connectors.
Because separate cables are used for low and mid/high sounds, the return current generated in the low speaker causes little interference with the mid/high speaker. The PM-11S1 and speakers of Connection Example 1 use a bi-wiring connection, therefore also refer to that page for help. Bi-wiring...
CONNECTIONS Connection Example 1: Basic Connection for Normal Stereo Playback Refer also to the instruction manuals of components to connect equipment correctly. Record player CD player To LINE OUT jacks OPEN/ OPEN/ SUPER AUDIO CD PLAYER SA-11S1 SUPER AUDIO CD PLAYER SA-11S1 CLOSE CLOSE PLAY...
Page 12
⇔ monaural miniplugs or stereo ⇔ stereo miniplugs as described “ABOUT FCBS” on pg. 17. Set the ID numbers for the PM-11S1 units as explained “HOW TO SET ID” on pg. 21. When the PM-11S1 of ID 1 is operated, those of ID 2 and ID 3 will operate in sync.
Page 13
FCBS connection, prepare 2 portable audio connection cables with monaural ⇔ monaural miniplugs or stereo ⇔ stereo miniplugs as described “ABOUT FCBS” on pg. 17. Set the ID numbers for the PM-11S1 units as explained “HOW TO SET ID” on pg. 21. When the PM-11S1 of ID 1 is operated, that of ID 2 will operate in sync.
If pressed again, the mode is canceled and the original volume level is restored. Attenuation level is set to –20 dB when the PM-11S1 is shipped from the factory, but it can be set to either –40 dB or -∞ (mute). For instructions on how to set attenuation level, see “How to...
VOLUME knob or the remote control- ler. When the PM-11S1 I is first activated, the attenuation level (dB) is displayed for the initial volume level. Volume Level Indication...
These jacks are for connecting to the balanced output jacks of a CD player or D/A converter. With the BALANCED IN- PUT jacks of the PM-11S1, pin 1 is GND, pin 2 is Cold and pin 3 is Hot. In the bi-amp mode, the R channel jack cannot be used.
NAMES AND FUNCTIONS OF PARTS RC-11PMS1 REMOTE CONTROLLER This remote controller can control the PM-11S1 and Marantz Super Audio CD players and DVD players that have a remote control receptor. The operations possible by remote control may differ with each component, therefore see the instruction manual that came with the component.
When the LINE 2 button is pressed, the buttons in groups , and . function as indicated in the below table. These buttons can be used only when a Marantz DVD player is connected to the LINE 2 input jacks.
(mute) by turning the VOLUME knob r until muting the volume level. Set the PHONO MC button ! 3 on the PM-11S1 to MC or MM according to the cartridge you are using. To use the speakers connected to the SPEAKER A terminals, press the SPEAKER A button o on the PM- 11S1.
ID 1. Select the input source from the INPUT SELECTOR knob e on the PM-11S1 or the input selector buttons z of the remote controller. And, press the REC OUT button !2 to turn the recording output of RECORDER 1 and 2 ON.
PM-11S1. The below figure is an example of four PM-11S1s connected by FCBS. The top PM-11S1 is the master unit of ID 1 and controls the three slave units of IDs 2 - 4. When the master...
ATTENUATION (ATT) Attenuation is a one-touch feature for reducing volume level. When the ATT button on either the PM-11S1 or the remote controller is pressed, the volume level is attenuated. When the PM-11S1 is shipped from the factory, the attenuation level is set to –20 dB, but it can be set to –20 dB, -40 dB or -∞.
Press the 3 and 4 buttons to set the volume level of the right channel. To trim the volume level of the ID 2 (slave) PM-11S1, press the TRIM button again and set volume level as in steps 1 - 3.
Page 24
The bass level of the left and right channels can be trimmed in 2 dB steps across a -8.0 - +8.0 dB range. When the PM-11S1 is shipped from the factory, the bass level is set to 0 dB. To trim the bass level, activate tone control by pressing the TONE button on either the PM-11S1 or the remote controller.
SPEAKER POWER ON/OFF button HOW TO SET ID If using the PM-11S1 by itself as a stereo amplifier, set the ID to “0”. When the PM-11S1 is shipped from the factory, the ID is set to “0”. When the ID is set to a number other than “0”, the PM- 11S1 cannot be used for standalone operation.
Temperature can also exceed the trip level of the protective circuits if the vents on the top of the PM-11S1 are covered or if the PM- 11S1 is installed on a cramped audio rack. In these cases, “PROTECT”...
In the event of difficulty, refer to your dealer or write directly to the nearest location to you that is listed on the Marantz Authorized Service Station list. If writing, please include the...
Remote controller ... 1 AAA batteries ... 2 Detachable AC power cable ... 1 Maximum outer dimensions (Amp) Width ... 440mm Height ... 165mm Depth ... 444mm Weight (Amp) ... 26.0kg INTEGRARED AMPLIFIER PM-11S1 DISPLAY ATT. TONE PRE OUT OPERATE SPEAKER REC OUT...
Page 29
You can find your nearest authorized distributor or dealer on our website. JAPAN Marantz Japan, Inc. U.S.A. Marantz America, Inc. EUROPE Marantz Europe B.V. Printed in Japan 35-1 Sagami Ohno 7-Chome, Sagamihara-shi, Kanagawa 228-8505, Japan 1100 Maplewood Drive, Itasca, IL 60143, U.S.A.
Need help?
Do you have a question about the PM-11S1 and is the answer not in the manual?
Questions and answers