Subscribe to Our Youtube Channel
Related Manuals for REMKO PG 12
Summary of Contents for REMKO PG 12
-
Page 1: Spare Parts
REMKO PG 12 / 12 E Propane gas heater Operation Technology Spare Parts Edition GB – M10 REMKO - powerful like a bear. -
Page 3: Table Of Contents
Our guarantee will become void when the unit supplied by us is used and installed for inadequate purposes, or maintained incorrectly, etc., or if it is changed without our prior consent! Mobile propane gas heater REMKO PG 12 / 12 E Contents Contents page... -
Page 4: Safety Instructions
Safety Instructions Description of Device The unit is a mobile, liquid gas fired heater without a When using this unit make sure always to observe the combustion chamber and with a fan for transporting hot applicable building and fire protection regulations as air. -
Page 5: General Instructions
General Instructions ◊ The unit may be operated only by those persons who ◊ In building site operation it is only allowed to use have been instructed regarding the unit’s operation hoses which are suitable for liquid gas. and the handling of liquid gas. According to regional regulations. -
Page 6: Before Starting
Before Starting Important information about the installation Make sure to charge a person with the operation of the When installing or removing the gas hose make sure to unit and with the supervision of the reservoirs and of the exert a counterpressure on the gas connection nipple of the unit using an open-end spanner SW 17 and observ- bottle stock who has been instructed sufficiently regard- ing the handlings concerned. -
Page 7: Starting
Starting 2. Press down pressure pin 2 of Important safety instructions thermoelectric gas valve (safety Make sure to place the gas reservoir only laterally behind pilot) and keep the pin pressed. the unit! 3. After approx. 2 or 3 sec. the piezo electric igniter 3 is to be actuated (possibly... -
Page 8: Maintenance
Maintenance ◊ Check ignition electrode and clean when necessary. Depending on the operation conditions the units are to be tested by an expert when necessary, but at least ◊ Set the ignition electrode when necessary. regularly every two years, to ensure their safe operation. 3 mm distance from the burnerhead. -
Page 9: Wiring Diagram
Nominal heat output filled in completely the “guarantee certificate” which is Heating capacity enclosed with every REMKO-heater and has returned it to REMKO GmbH & Co. KG in due time after the unit’s Air output m³/h sale and commissioning. Fuel/type of gas liquid gas Cat. -
Page 10: Exploded View
Exploded View We reserve the right to make modifications in dimensions and construction in the interests of technical progress. -
Page 11: Spare Part List
Spare Part List Description Ref.-No. transport handle 1101142 outside casing PG 12 1103801 outside casing PG 12 E (stainless steel) 1103832 inside casing 1103802 retaining ring 1103811 discharge protection grille 1103803 gas burner 1103804 ignition electrode 1103818 terminal strip, 4 x... -
Page 12: Troubleshooting
Troubleshooting trouble: cause: – unit doesn’t start 1 – 2 – 3 – 4 – 7 – unit stops during operation 2 – 4 – 7 – 12 – 13 – fan blows, but gas supply is blocked 4 – 5 – 8 – 9 – 12 resp. -
Page 13: Maintenance Log
Maintenance Log Model: : ........ Model No.: : ........9 10 11 12 13 14 15 16 17 18 19 20 Clean unit -surface- Clean unit -interior- Clean fan blade Clean combustion chamber Clean gas burner Set/replace ignition electrode Check gas hose Check gas leading parts for leaks Check safety facility Check protection guards... - Page 16 REMKO GmbH & Co. KG Klima- und Wärmetechnik D-32791 Lage Im Seelenkamp 12 • D-32777 Lage PO Box 1827 • Phone +49 (5232) 606 - 0 +49 (5232) 606260...
Need help?
Do you have a question about the PG 12 and is the answer not in the manual?
Questions and answers