Proper Care And Maintenance - Brinkmann 810-6420-S Assembly And Operating Instructions Manual

WARNING: If a bristle brush is used to clean any of the cooking surfaces, ensure no loose bristles remain
on the cooking surfaces prior to grilling as loose bristles may attach to food.
CLEANING INTERIOR OF GRILL:
• We recommend cleaning off food residue immediately after cooking by gently scrubbing grates with wire bristle brush
and then turning burners to HIGH for approximately 5 minutes.
WARNING: DO NOT leave grill unattended when grill is on. Wear oven mitts to protect from burns.
• The heat from the burners will burn off most food/grease residue from grates & heat tents and turn it to an ash like
substance which will fall to the bottom of the fi rebox or grease tray. After the grill cools (approximately 30 minutes)
remove grates and heat tents and brush the ash and any grease out of the fi rebox. Clean and replace grease cup.
Inspect the heat tents for damage or deterioration before reinstalling in the grill. (Replacements can be ordered by
calling 800-527-0717.)
• Wash the grates and heat tents with a mild detergent and rinse with hot water periodically if desired.
CAUTION: DO NOT allow ash residue to remain on the grease tray or fi rebox as it could block proper grease
drainage of the grill.
INTERIOR OF GRILL LID:
• Smoke will accumulate inside grill lid and may fl ake onto your food. Clean the inside of the grill lid with scrub brush
and baking soda/water solution. Dry thoroughly. Do not mistake this for paint. The interior of gas grill lids are not
painted.
MAINTAINING EXTERIOR OF GRILL:
• To protect your grill from excessive rust, the unit must be kept clean and covered at all times when not in use.
• Painted surfaces. Wash with mild detergent or non-abrasive cleaner and warm soapy water.
• Stainless steel surfaces. To maintain your grill's appearance, wash with mild detergent and warm soapy water
and wipe dry with a soft cloth after each use. Baked-on grease deposits may require the use of an abrasive plastic
cleaning pad. Use only in direction of brushed fi nish to avoid damage. Do not use abrasive pad on areas with
graphics. Car wax may help protect the exterior fi nish of your grill.
• Porcelain surfaces. Because of glass-like composition, most residue can be wiped away with a solution of baking
soda and water or specially formulated cleaner. Use non-abrasive scouring powder such as baking soda for stubborn
stains.
• Plastic and rubber parts. Wash with warm soapy water and wipe dry. Do not use citrisol, abrasive cleaners,
degreasers or a concentrated grill cleaner on plastic parts. Damage to and failure of parts can result.
RUST:
• Discoloration, rust and rust pits can occur as a result of high cooking temperatures, acidic marinades, grease fi res
and exposure to coastal climates or other natural elements.
• Rust spots on the interior surface can be buffed, cleaned, then lightly coated with vegetable oil or vegetable oil spray
to minimize rusting.
• Never use cleaners containing chlorine or store swimming pool supplies or chemicals in cart compartment as
chlorine promotes rust.
BURNER CLEANING AND MAINTENANCE:
• Keep the appliance free and clear of combustible materials, gasoline and other fl ammable vapors and liquids.
• Keep the ventilation openings of the cylinder enclosure free and clear of debris.
• Visually check burner fl ames for proper operation (see pictorial in "Burner Assembly/Maintenance" under Proper Care
and Maintenance). Spiders or other insects can nest in the burner causing gas blockage.
• For safe grilling and peak performance of your grill, perform these checks at least twice per year or after extended
periods of storage.
• Be sure to tighten up all hardware (nuts, bolts, screws, etc.) at least twice per year.
CAUTION: Some parts may contain sharp edges. Wear protective gloves if necessary.
• Remove the cooking grills, heat distribution plates, and burners from inside your grill. Use a brush with hot water
and detergent to remove excess residue. NEVER use a commercial oven cleaner. Rinse completely with water.
Towel dry and replace all components as described in the assembly instructions.
13
PROPER CARE & MAINTENANCE: