Advertisement
Available languages
Available languages
ELECTRONIC
CONTROLS
SET-UP INSTRUCTIONS
H.O0
EXTRA
RINSE
EXTRA RINSEUpgradePrice- Increase or decreasebetween0
and 200by pressingthe LEFTUPPER or RIGHTUPPERkeypad.
Factorypresetfor 0 quarters= $0.00.
--> Pressthe LEFTMIDDLEkeypadonceto advanceto next code.
J.Cd
COIN/DEBITOPTION
J.Cd
Bothcoin &debitselected.
J.C_
Coinsselected,debitdisabled.Pressthe LEFTLOWER key pad
3 times for thisselection.
If cycle counter
(9.0C) is selected,
the following
is true:
1 xx Number of cycles in THOUSANDS.
1 02 = 2,000
2xxx Number of cycles in ONES.
2225 =
225
TOTAL CYCLES = 2,225
This is "VIEW ONLY" and cannot be cleared.
Press the LOWER MIDDLE key pad once to advance
to next code.
J._d
DebitCardselected,coins disabled.Pressthe LEFTLOWER key
pad3 timesfor thisselection.
J.Ed
Enhanced Debitis self-selected when a Generation 2 cardreader
is installedin the washer. T he Edoption cannotbe manually
selectedor deselected.
END OF SET-UP PROCEDURES
-e Pressthe LEFTMIDDLEkeypadonceto advanceto next code.
L.O0
PRICESUPPRESSION OPTION
This optioncausesthe customerdisplayto show'ADD' or
'AVAILABLE' ratherthanthe amountof moneyto add. (Used
mainlyin debitinstallations.)
NotSelected'OFF'.
LO0
L.PS
Selected'ON'. Pressthe LEFTLOWERkeypadoncefor this
selection.
--> Pressthe LEFTMIDDLEkeypadonceto advanceto next code.
n. CE
CLEARESCROW OPTION
Whenselected,moneyheld inescrowfor 30 minuteswithout
further escrowor cycleactivitywill be cleared.
n. CE
Selected'ON'.
n. O0
Notselected'OFF'.Pressthe LEFTLOWER key padonceto
deselectthisselection.
--> Pressthe LEFTMIDDLEkeypadonceto advanceto next code.
U.O0
PENNYINCREMENT OFFSET
U.O0
This represents the pennyincrementpriceoffset usedin
Generation2 (Enhanced Debit)PR models.Choosefrom 0-4
penniesby pressingthe LEFTUPPERkeypad.
--> Pressthe LEFTMIDDLEkeypadonceto advanceto next code.
A3.02
NORMAL CycleSettings.Allowsthe ownerto selectthe cycle
defaultoptions ofWaterTemperature, S oilLevel,andExtraRinse.
SeeTable1 for specificsettings.Normalis set to 02from the
factory.
A4.00
DELICATES C ycleSettings.Allows the ownerto selectthe cycle
defaultoptions ofWaterTemperature, S oilLevel,andExtraRinse.
SeeTable1 for specificsettings.Delicates is set to O0 from the
factory.
A5.0F
POWERWASH C ycleSettings.Allowsthe ownerto selectthe cycle
defaultoptions ofWaterTemperature, S oilLevel,andExtraRinse.
SeeTable1 for specificsettings.Powerwash is set to OFfromthe
factory.
If money counter (1.00 or 1.00) is selected,
the following
is
true:
3 xx Number of dollars in HUNDREDS.
3 01 = $1,000.00
4xxx Number of dollars in ONES.
4600 = $
600.00
5 xx Number of CENTS.
5 75 = $
00.75
TOTAL = $1,600.75
EXIT FROM SET-UP MODE
[]
PD Models: Reinstall access door.
[]
PR Models:
-_ Unplug washer or disconnect
power.
-_ Open console, reinsert plug into AA1, close console.
-_ Plug in washer or reconnect power.
if preferred, just wait through 2 minutes of inactivity. All settings
will be saved and the display will revert to Select Cycle screen.
Table 1
A3, A4,
Extra
Soil
Wash
A3, A4,
Extra
Soil
Wash
or A5
Rinse
Level
Temp
or A5
Rinse
Level
Temp
O0
Off
Off
Cold
08
On
Off
Cold
01
Off
Off
Cool
09
On
Off
Cool
02
Off
Off
Warm
OA
On
Off
Warm
03
Off
Off
Hot
Ob
On
Off
Hot
04
Off
On
Cold
Oc
On
On
Cold
05
Off
On
Cool
Od
On
On
Cool
06
Off
On
Warm
OE
On
On
Warm
07
Off
On
Hot
OF
On
On
Hot
Technician Service Access Code
This method is only available on washers set to free vend (6 00).
To enter service
mode:
Press the LEFT UPPER, RIGHT LOWER, RIGHT UPPER, and
LEFT LOWER key pads within 10 seconds.
To exit service
mode:
From service code 8.xx, press the LEFT UPPER key pad
for 4 seconds
or
Wait 2 minutes without touching any key pads (without diagnostic
modes running)
or
Power down the washer, then reapply power
NOTE: if a service cycle is in progress upon exiting service mode,
the cycle will complete normally with cycle status information
displayed. The display will resume normal customer operation
mode when the cycle ends.
18
Advertisement
