Advertisement
( Continued from page 3 )
Unlike the standard gas range
THIS COOKTOP IS NOT REMOVABLE.
Do not attempt
to remove this cooktop.
GAS SURFACE BURNER ORIFICE DATA CHART (Burner Style #1)
BTU Rating / Natural
Gas
5,000
9,500
12,000
14,000
16,000
Natural
Gas Orifice
1.01
1.54
1.75
1.93
1.99
LP Gas Orifice
.68
.89
.95
1.01
1.15
LP Orifice Marking
Color
Blue
None
Green
Red
Black
BTU Rating / LP Gas
4,500
8,000
10,000
11,000
14,000
_*Note: For
at elevations
above 2000
operation
ft., appliance
rating
_shall be reduced
at the rate of 4 percent
for each 1000 ft. above sea
level.
For all burner
locations:
a. Remove
the top grates
and burner
caps (See Fig. 10).
b. Lift off the burner
heads.
i
Fig. 10
Burner
Burner
Head
Do Not _
R .....
7 Electrode
Fig. 11
7mm
Nut
Driver
c. Remove the factory installed natural gas orifices one at a time from the center of the orifice holder using a 7 mm nutdriver (See Fig. 11).
Remember to keep the original Natural Gas Orifices for later conversion to Natural Gas.
d. Replace the orifice with the correct LP/Propane gas orifice (See the Surface
Burner Orifice Data Chart ; also refer to Fig 9 for the
correct
LP orifice installation at each of the surface burner locations).
Tighten each orifice until snug. Use caution not to overtighten.
Repeat for each surface burner.
e. Replace the burner heads. Match letter located under center of Burner Caps with letter located inside Burner Heads. Match the letter
stamped on Burner Skirt with Burner Head and Burner Cap. (Refer to Fig. 9). Be sure burner heads mate correctly with each surface
igniter, then replace the burner caps and burner grates.
Unlike the standard
gas range,
THIS COOKTOP IS
NOT REMOVABLE.
BURNER
STYLE #2 CONVERSION
INSTRUCTIONS
Use caution
when replacing
each burner
cap so the electrode
is not damaged.
Do not attempt
to remove this
cooktop.
Fig. 12
For all burner
locations:
a. Remove Burner Grates & Burner Caps.
Mounting screws
7ram Nut Driver
oril
Fig. 13
Ignitor Alignment
Fig. 14
b. If the opening in the burner is too small to allow removal of the orifice, remove the burner as follows:
Remove 2 screws using #1 square tip driver and
remove Burner Heads (Figs 12 ). NOTE - Some models may have 3/16" hex head screws instead of square drive screws.
c. Remove the factory installed natural gas orifices from the center of the orifice holders using a 7 mm nutdriver (See Fig. 13). Save the natural gas
orifices
removed
from the appliance
for possible
future conversion
back to natural gas.
d. Following the chart below select the appropriate
LP/Propane gas orifice from the envelope labeled SCREW
MOUNTED
BURNER
LP KIT.
EXAMPLE:
Natural Gas orifcie marked 1.07 is replaced by LP orfice marked .66. Tighten all orifices until snug. Use CAUTION
not to overtighten.
e. Replace burner heads at all locations and tighten each position with original screws using #1 square tip driver. Make sure that the center of the ignitor
aligns with the center nib in the burner head (Figs. 14). Heads MUST have a Burner Cap installed to insure proper ignition and gas flame size.
GAS SURFACE
BURNER ORIFICE DATA CHART (Burner
Style #2)
BTU Rating / Natural Gas
5,000
9,500/10,000
12,000
14,000
15,000
16,000
17,000
18,000
Natural Gas Orifice
1.07
1.46
1.67
1.87
1.95
1.98
2.1
2.2
L P Gas Orifice
0.66
0.93
1.02
1.09
1.09
1.18
1.18
1.18
LP Orifice Marking Color
Pink
White
Yellow
Brown
Brown
Silver
Silver
Silver
BTU Rating / LP Gas
5,000
9,500
12,000
14,000
14,000
16,000
16,000
16,000
4
*Note: For operation
at elevations
above 2000 ft., appliance
rating
shall be reduced
at the rate of 4
percent
for each 1000 ft. above
sea level.
Advertisement
