Shop-Vac SERIES 586 User Manual page 4

TOP HANDLE ASSEMBLY
(Not standard with all models)
To attach top handle, align holes in handle and holes in motor cover
and secure with screws provided (Figure 1).
REAR CASTER ACCESSORY CADDY AND
FRONT CASTER FEET ASSEMBLY
(Not standard with all models)
You will find four casters, two caster feet, an accessory caddy and
four screws with your wet/dry vacuum.
If your accessory caddy looks like the one pictured in (Figure a)
assemble as follows.
1. With cord disconnected from receptacle and tank cover
removed, turn tank upside down so that the bottom is facing up.
2. Insert two caster feet into adjacent slots at front of tank. Secure
with screws provided.
3. Take accessory caddy and place into remaining slots at back of
tank. Secure with screws provided (Figure 2).
4. Install casters into caddy and feet by inserting the caster stems
into the holes provided. Apply pressure and twisting motion until
casters snap into place.
If your accessory caddy looks like the one pictured in (Figure b) assemble as follows.
1. With cord disconnected from receptacle and tank cover removed, turn tank upside down so
that the bottom is facing up.
2. Take accessory caddy and place into slots (on rear of tank opposite of drain). Secure with
screws provided (Figure 3).
3. With tank drain facing you, take caster foot marked with the letter A (Figure 4) and place in
slot on left side of tank also marked with the letter A. Secure with screw provided (Figure 5).
4. Take caster foot marked with the letter B (Figure 6) and place in slot on right side of tank
also marked with the letter B. Secure with screw provided (Figure 7).
5. If flat washers are included in hardware package, place flat washer over stem of caster
before installing casters into feet or accessory caddy. NOTE: Flat washers are not required
with all units.
6. Install casters into caster feet and accessory caddy by inserting the caster stems into the
holes provided. Apply pressure and twisting motion until caster snap into place (Figure 8 &
9).
b.
5. 6.
8.
1.
a.
2.
3. 4.
7.
9.
ASSEMBLY
REAR CASTER DOLLY/TOOL HOLDER
AND FRONT CASTER FEET ASSEMBLY
(Not standard with all models)
You will find four casters (c.), two caster feet (d.), rear caster dolly/tool holder (e.), and four
screws with your wet/dry vacuum. Assemble as follows:
c.
1. With cord disconnected from receptacle and tank cover removed, turn tank upside down so
that the bottom is facing up.
2. Take rear caster dolly and place into slots (on rear of tank, opposite of drain) and secure
with screws provided (Figure 10).
3. If flat washers are included in hardware package place flat washer over stem of caster
before installing casters into rear caster dolly.
NOTE: Flat washers are not required with all units.
4. Insert casters into bottom of rear caster dolly by placing stem of caster into holes provided.
Apply pressure and twisting motion until casters snap into place (Figure 11).
5. With tank drain facing you, take caster foot marked with the letter A (Figure 12) and place
in slot on left side of tank also marked with the letter A and secure with screw provided
(Figure 13).
6. Take caster foot marked with the letter B (Figure 14) and place in slot on right side of tank
also marked with the letter B and secure with screw provided (Figure 15).
7. If flat washers are included in hardware package, place flat washer over stem of caster
before installing casters into feet.
NOTE: Flat washers are not required with all units.
8. Insert casters into feet by placing stem of caster into holes provided. Apply pressure and
twisting motion until casters snap into place (Figure 16).
9. Return tank to upright position.
10. Place tool basket (Not standard with all models) with curved surface against tank on rear
caster dolly assembly (Figure 17).
10
13
16
REAR WHEEL DOLLY/TOOL HOLDER
AND FRONT CASTER FEET ASSEMBLY
(Not standard with all models)
You will find two casters (f.), two large rear wheels (g.), one axle (h.), rear dolly/basket (i.), two caster
feet (j.) and four screws with your wet/dry vacuum. Assemble as follows:
f
g
1. With cord disconnected from receptacle and tank cover removed, turn tank upside down so that the
bottom is facing up.
4
d.
e.
11 12
15
14
17
h
i j