Controls - GE GSE25ESHBSS Owner's Manual And Installation Instructions

About the controls on the refrigerator.
Your controls will look like one of the following:
, lJ
Startup Steps for Proper Temperature Control
STEP&-Set Fresh Food Control on "5."
STEP2-Set Freezer Control on "5."
STEP I-WAtT 12 HOURS for temperature to stabilize,
STEP 4-tf a change is needed, move the control one number at a time
and allow 12 hours for temperature to stabilize,
REFRIGERATOR
®
0 IS OFF
9 IS COLDEST
aCustT®m_m
• • ® 6
NOTE'Turning the refrigerator to the 0 (off)setting via the controls does
not shut off electrical power to the refrigerator,
Control settings will vary based on personal preferences,usage and
operating conditions and may require more than one adjustment
About Energy Smart
TM
Models Controls
Energy Smart
TM
is located on the controls of models
equipped with the feature, as shown in the image,
What Energy Smart
TM
Does
If the ACM (Appliance Communicatiorl Module) is conrlected
to your refrigerator and is receiving utility rate informatiorl,
then Energy Smart
TM
feature alters the performance
of the refrigerator. It minimizes energy consumptiorl
when directed by the Nucleus
TM
(separately purchased
device) or Smart Meter, The Energy Smart
TM
feature carl
cause changes in refrigerator or freezer compartment
temperatures and can cause changes in the rate of ice
cube production,
Energy Smart
TM
Override •
Pressthe Energy Smart
TM
pad for 3 seconds to Er_-n_u_--_
override the Energy Smart feature, The LED
above the pad will flash multiple times to confirm .aa 3_w_
a successful override of the feature, This will
disable the feature from altering the performance of your unit for 18
hours, Eighteen hours after the feature has been disabled, the Energy
Smart
TM
feature will continue normal operation,
To Change Temperature Control Setting with Touch Pads:
• Freezer setting is on the left side of the display,
• Refrigerator setting is on the right side of the display,
- Press the Warmer or Colder pad for compartment and
direction desired,
- Present control setting number will illuminote.
- Eoch time the pod is touched, comportment setting chonges
one number,
A display of 1 is warmest and 9 is the coldest setting,
To Turn Cooling Off:
To stop cooling in the refrigerator andfreezer compartments, first
repeatedly press the Warmer pad for the freezer until its display
continuously flashes "1", Then, using the refrigerator control,
repeatedly press Warmer until both displays flash "0", "0" in both
displays turns off the cooling system, On some models, it may be
necessary to set only one control to Oto turn off cooling in both
compartments,
NOTE: Turning the refrigerator to the 0 (oft)setting via the controls
does not shut off electrical power to the refrigerator,
Control settings will vary based on personal preferences, usage and
operating conditions and may require more than one adjustment
®
Adjust Ternperoture
(WrJrmer_ _ (Wormer _ _rboOCool_
0 ® 0 ® 0 •
Filt e ate rush ube ick I
Loc
No_d _ s_onds to Reset He_d _ seconds
@
Locking the Dispenser (on some models)
for 3 seconds to lock the
dispenser and control panel,
.o_as..... a, To unlock, press and hold
the key pads again for 3 seconds,
The temperature controls are preset in the factory at 37°F for the
refrigerator compartment and 0°F for the freezer compartment,
Allow 24 hours for the temperature to stabilize to the preset
recommended settings,
The temperature controls can display both the SETtemperature as
well as the actual temperature in the refrigerator and freezer, The
actual temperature may vary slightly from the SETtemperature based
on usage and operating environment,
6
Setting either or both controls to OFFstops cooling in both the freezer
and refrigerator compartments, but does not shut off electrical power
to the refrigerator,
NOTE'The refrigerator is shipped with protective film covering the
temperature controls, If this film was not removed during installation,
remove it now,