Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Fimer Tp 72
Summary of Contents for Fimer Tp 72
- Page 1 INSTRUCTION MANUAL 910.100.276GB REV00 1 di 28...
- Page 2 910.100.276GB REV00 2 di 28...
-
Page 3: Warning
WARNING 910.100.276GB REV00 3 di 28... - Page 4 910.100.276GB REV00 4 di 28...
- Page 5 910.100.276GB REV00 5 di 28...
-
Page 6: Technical Data
1 MANUFACTURER’S NAME, ADRESS AND COMPANY 11 RATED INPUT VOLTAGE LOGO 12 MAXIMUM RATED INPUT CURRENT 2 MODEL 13 MAXIMUM EFFECTIVE INPUT 3 SERIAL NUMBER CURRENT 4 BLOCK DIAGRAM 14 APPLICABLE STANDARDS 5 TYPE OF WELDING 15 RANGE OF WELDING VOLTAGE- 6 SUITABLE FOR USE IN AN ENVIRONMENT WITH CURRENT INCREASED HAZARD OF ELECTRIC SHOCK. -
Page 7: Table Of Contents
INSTRUCTION MANUAL Fimer S.p.A. thanks you for selecting this unit: It will prove to be a useful, problem-free tool for many years to come if the instructions contained in this manual are followed scrupulously. This manual must be considered as an integral part of the unit and must accompany it when it change location or is resold. -
Page 8: Safety Rules
SAFETY RULES INTRODUCTION: We therefore recommend following strictly the instructions contained in this manual. WARNING: Your safety is in your hands! Follow carefully all the safety instructions. It is your duty to protect yourself and others from risks related to welding operations. The operator is responsible for his own safety and that of those who are in the work zone. -
Page 9: Pressure Regulator
(the "infant mortality"). FIMER use highly selected oversized components and performs a test bench for every unit built. FIMER has prepared this manual to provide the user with both instructions for use, is the description of the principles of operation for the TP plasma cutting generators. -
Page 10: How To Start
HOW TO START This part of the manual is important for the proper use of the plasma cutting generator. This manual not contain special instructions for maintenance since these generators are maintenance- free. The only precautions to be taken are those of any electrical machine with metal frame. Let us hope to avoid shock, dripping, excessive heat, and any other abnormal situations. - Page 11 Cutting gas connection Check if the pressure and air flow rates are in accordance with to the values required by the torch The plasma cutter uses a jet of compressed air both for the blowing of the arc and for cooling the torch The air circuit includes a pressure regulator, adjusted to 3.5 bar.
-
Page 12: Operator Panel
OPERATOR PANEL 910.100.276GB REV00 12 di 28... -
Page 13: Remote Control Connector
0VDC output current: 0A input signal: 5VDC output current:: 110A WARNING: To make this change you need to contact a service center or directly FIMER − Pin 2 voltage output +15 V /-20mA (output) − PIN 5-9 ground. -
Page 14: Adjustments
Ensure that the new electrode and the nozzle are about to be mounted are well cleaned and degreased. To avoid damaging the torch always use genuine parts FIMER. THE OPERATIONS REQUIRING ACCESS INSIDE THE MACHINE MUST BE EXECUTED AFTER DISCONNECT THE... -
Page 15: Practical Advice
Ensure that the new electrode and the nozzle are about to be mounted are well cleaned and degreased. To avoid damaging the torch always use genuine parts FIMER. THE OPERATIONS REQUIRING ACCESS INSIDE THE MACHINE MUST BE EXECUTED AFTER DISCONNECT THE... -
Page 16: Schematic Diagram
SCHEMATIC DIAGRAM 910.100.276GB REV00 16 di 28... -
Page 17: Spare Parts
SPARE PARTS DESCRIPTION Inductor Pilot Arc Card Handle Air reducer Keyboard Torch Connector HP Solenoid Filter Card Resistor: 15 Ohm 50 W Ground Connector LP Solenoid 13/1 Reduction for LP High frequency card Resistor: 33 Ohm 100 W Toroidal transformer Power Supply Card Inverter Card Regulator Card...