Advertisement
Quick Links
Advertisement
Related Manuals for Fimer KRONOS 500 dual-pulse
Summary of Contents for Fimer KRONOS 500 dual-pulse
- Page 1 INSTRUCTION MANUAL KRONOS dual-pulse Ed. 2016_05_03 910.100.539GB REV01...
- Page 2 It is user’s responsibility to keep it intact and in good conditions. The manufacturer has the right to apply modifies in every moment or without any forewarning. Every Fimer product is minded, designed and produced in Italy in our sites. This is guarantee of high quality and reliability.
- Page 3 Qualquer intervenção ou modificação que não seja autorizada pela FIMER anularà a validade desta declaração. Denna försakran upphör att galla vid eventuella ingrepp eller andringar som ej ar godkanda av FIMER. ledere niet door FIMER geautoriseerde ingreep of wijziging doet de geldigheid van deze verklaring vervallen.
- Page 4 Our production, assistance and training site is exclusively on Italian region and we can praise a 100% MADE IN ITALY. In addition, Fimer has inside a complete production chain thanks to an efficient and high quality metal carpentry department, lines for the production of electronic boards with SMD technology and testing/assembly department which make possible to create the entire product.
- Page 6 KRONOS dual-pulse 5T5.555.452...
-
Page 7: Warning Symbols
WARNING SYMBOLS WARNING SYMBOLS FIRE READ THE INSTRUCTION MANUAL PRECAUTIONS DANGER DISPOSAL (Indicating a hazard that could cause injury or damage) INFORMATION ELECTRIC SHOCK INSTALLATION (Indicating the danger of electric shock) INSTRUCTIONS UNPACKING DANGER OF FIRE. INSTRUCTIONS DANGER EXPLOSIONE RISK SUITABLE FOR ENVIRONMENT WITH INCREASED Indicating the risk of explosion in the event of improper handling HAZARD OF ELECTRIC SHOCK... - Page 8 FOREIGN OBJECTS Never block the air vents with REPAIRS Never attempt to repair the Welder foreign objects and avoid any contact with liquids. yourself. Always refer to the manufacturer or an authorized repairer. All warranty provisions will Clean using just a dry cloth. These safety precautions immediately become null and void if any repair, or attempt to repair, apply even when the unit is switched off.
- Page 9 WORK-AREA FLOORING The work-area flooring DAMAGED GAS CYLINDERS NEVER use damaged MUST be fireproof. or faulty cylinders. CYLINDER RELOCATION NEVER lift a gas cylinder by holding the regulator. WORK-AREA SURFACES Work benches or tables used during welding MUST have fire- GAS CYLINDERS Do not expose gas cylinders to proof surfaces.
- Page 13 DUAL PULSE PULSE function...
- Page 18 Unscrew the ball-grip knob in the If necessary, depending on the size of Remove the plastic wrap from the centre of the spool support of the the spool used, remove the bearing new spool and place the spool on the welding wire.
- Page 33 TORCH P-BI-LEV P-DOWN P-UP P-START COM(-) DOWN REMOTE P-START BIT-REM F (+5.1V) C (HI-RIF) COM-I (LO-RIF) -SPOOL +SPOOL POT1 POT1 START REMOTE...
- Page 38 Sg2/Sg3 CrNi AiSi 308 CrNi AiSi 316 Al, AlMg, AlSi (7,85kg/dm (7,93kg/dm (7,98kg/dm (~2,70kg/dm 0,8mm 1,0mm 1,2mm 0,8mm 1,0mm 1,2mm 0,8mm 1,0mm 1,2mm 1,0mm 1,2mm 0,003946 0,006165 0,008878 0,003986 0,006228 0,008969 0,004011 0,006267 0,009025 0,002121 0,003054...
- Page 49 Nero Grigio Marrone NOT ISOL. CAN Nero - BUS Rosso + BUS Cod.:101.601.1035 Cod.: 101.601.1035 SK Pot.451.191.181 Nero - BUS Rosso + BUS +DINSE- LINE-AUX TL-PWR FAN-INV1 FAN-INV2 (MIG) LINE Nero (-DINSE) FAN 24V cod.:019.501.167 FAN 24V cod.:019.501.167...
- Page 50 Tubo GAS MIG Verde (FEED-S) Grigio +24Vdc EV MIG EV TIG Tubo GAS TIG Torch Remote Verde Rosso Rosso (Spool+) Nero (Spool-) Tubo GAS TIG Tubo GAS MIG...
- Page 52 ASSISTANCE +39-039-6079326 +39-039-6079334 Technical Assistance: service.welding@fimer.com Monday To Friday 09.00 / 12.30 15.30 / 17.00 Via J.F. Kennedy - 20871 Vimercate (MB) Italy Phone: +39 039 98981 Fax +39 039 6079334 www.fimer.com info@fimer.com...