Page 1 Patriot 2 0 1 6 O W N E R ’ S M A N U A L I n f o r ma t i o n P r o v i d e d b y :...
Page 2 VEHICLES SOLD IN CANADA This manual illustrates and describes the operation of With respect to any Vehicles Sold in Canada, the name FCA features and equipment that are either standard or op- US LLC shall be deemed to be deleted and the name FCA tional on this vehicle.
Page 3: Introduction 3
TABLE OF CONTENTS SECTION PAGE INTRODUCTION ............. . . 3 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE .
Page 4 I n f o r ma t i o n P r o v i d e d b y :...
Page 5: Table Of Contents
INTRODUCTION CONTENTS INTRODUCTION ......4 WARNINGS AND CAUTIONS ....7 ROLLOVER WARNING .
Page 6: Introduction
4 INTRODUCTION INTRODUCTION When it comes to service, remember that your authorized dealer knows your Jeep® vehicle best, has factory-trained Congratulations on selecting your new FCA US LLC technicians and genuine MOPAR® parts, and cares about vehicle. Be assured that it represents precision workman- your satisfaction.
Page 7: How To Use This Manual
INTRODUCTION 5 control. Failure to operate this vehicle safely may result seat belts could cut the highway death toll by 10,000 or in a collision, rollover of the vehicle, and severe or fatal more each year and could reduce disabling injuries by injury.
Page 8 6 INTRODUCTION I n f o r ma t i o n P r o v i d e d b y :...
Page 9: Warnings And Cautions
INTRODUCTION 7 WARNINGS AND CAUTIONS This Owner’s Manual contains WARNINGS against operating procedures that could result in a collision or bodily injury. It also contains CAUTIONS against proce- dures that could result in damage to your vehicle. If you do not read this entire Owner’s Manual, you may miss important information.
Page 10: Vehicle Modifications/Alterations
8 INTRODUCTION VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death. Right Front Body VIN Location NOTE: It is illegal to remove or alter the VIN. I n f o r ma t i o n P r o v i d e d b y :...
Page 11 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS ▫ Rearming The System ....19 A WORD ABOUT YOUR KEYS ... . .12 ▫...
Page 12 10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Sound Horn With Remote Key Lock ..22 ▫ To Exit Remote Start Mode And Drive The Vehicle ......29 ▫...
Page 13 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 ▫ Important Safety Precautions ....39 ▫ Transporting Passengers....97 ▫...
Page 14: A Word About Your Keys
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS Ignition Key Removal The authorized dealer that sold you your new vehicle has 1. Place the shift lever in PARK (if equipped with an the key code numbers for your vehicle locks. These automatic transmission).
Page 15 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 NOTE: If you try to remove the key before you place the shift lever in PARK, the key may become trapped tem- porarily in the ignition switch cylinder. If this occurs, place the shift lever in PARK, rotate the key clockwise slightly, and then remove the key as described above.
Page 16: Locking Doors With A Key
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Locking Doors With A Key WARNING! (Continued) You can insert the key with either side up. To lock the • Allowing children to be in a vehicle unattended is door, turn the key to the right. To unlock the door, turn dangerous for a number of reasons.
Page 17: Sentry Key
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 SENTRY KEY During normal operation, after turning on the ignition switch, the Vehicle Security Light will turn on for three The Sentry Key Immobilizer System prevents unauthor- seconds for a bulb check. If the light remains on after the ized vehicle operation by disabling the engine.
Page 18: Replacement Keys
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CAUTION! CAUTION! The Sentry Key Immobilizer system is not compat- Always remove the Sentry Keys from the vehicle and ible with some aftermarket remote starting systems. lock all doors when leaving the vehicle unattended. Use of these systems may result in vehicle starting Duplication of keys may be performed at an authorized problems and loss of security protection.
Page 19: Customer Key Programming
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 Customer Key Programming 4. Insert a blank Sentry Key into the ignition switch. Turn the ignition switch to the ON/RUN position within 60 If you have two valid Sentry Keys, you can program new seconds.
Page 20: General Information
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: If a programmed key is lost, see your authorized NOTE: Changes or modifications not expressly approved dealer to have all remaining keys erased from the sys- by the party responsible for compliance could void the tem’s memory.
Page 21: To Arm The System
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 To Arm The System Rearming The System If something triggers the alarm, and no action is taken to 1. Remove the key from the ignition switch and get out disarm it, the Vehicle Security Alarm will turn off the of the vehicle.
Page 22: Vehicle Security Alarm Manual Override
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE once the Vehicle Security Alarm is armed (after 16 seconds), when you pull the door handle to exit, the alarm will sound. If this occurs, push the UNLOCK button on the RKE transmitter to disarm the Vehicle Security Alarm.
Page 23: Remote Key Unlock, Driver Door/All First Press
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 within five seconds to unlock all doors and liftgate. The than 10 seconds. Then, push and hold the UN- turn signal lights will flash to acknowledge the unlock LOCK button while still holding the LOCK button. signal.
Page 24: Illuminated Approach - If Equipped
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Illuminated Approach — If Equipped Sound Horn With Remote Key Lock This feature activates the headlights for up to 90 seconds This feature will cause the horn to chirp when the doors when the doors are unlocked with the RKE transmitter.
Page 25: Flash Lights With Remote Key Lock/Unlock
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 • For vehicles equipped with the EVIC, refer to “Elec- 3. Test the feature while outside of the vehicle by pushing the LOCK button on the RKE transmitter tronic Vehicle Information Center (EVIC)/Personal with the ignition switch in the LOCK position and Settings (Customer-Programmable Features)”...
Page 26: Using The Panic Alarm
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Repeat these steps if you want to return this feature NOTE: When you turn off the Panic Alarm by pushing to its previous setting. the PANIC button a second time, you may have to move closer to the vehicle due to the radio frequency noises of NOTE: Pushing the LOCK button on the RKE transmitter the system.
Page 27: General Information
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 two halves of the RKE transmitter apart. Make sure 3. To reassemble the RKE transmitter case, snap the two not to damage the elastomer seal during removal. halves together. NOTE: If the RKE transmitter is equipped with a screw, reinstall and tighten the screw until snug.
Page 28: Remote Starting System - If Equipped
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Changes or modifications not expressly approved How To Use Remote Start by the party responsible for compliance could void the All of the following conditions must be met before the user’s authority to operate the equipment. engine will remote start: REMOTE STARTING SYSTEM —...
Page 29: Remote Start Abort Message On Electronic Vehicle Information Center (Evic) - If Equipped
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 • Remote Start Aborted — Hood Ajar WARNING! • Remote Start Aborted — L/Gate Ajar • Do not start or run an engine in a closed garage or • Remote Start Aborted — Fuel Low confined area.
Page 30: To Exit Remote Start Mode Without Driving The Vehicle
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Any engine warning lamps come on. NOTE: • The park lamps will turn on and remain on during • Low Fuel Light turns on. Remote Start mode. • The hood is opened. •...
Page 31: To Exit Remote Start Mode And Drive The Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 To Exit Remote Start Mode And Drive The Vehicle 1. This device may not cause harmful interference, and Before the end of the 15-minute cycle, push and release 2. This device must accept any interference received, the UNLOCK button on the RKE transmitter to unlock including interference that may cause undesired op- the doors and disarm the Vehicle Security Alarm (if...
Page 32 30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • Never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured.
Page 33: Power Door Locks
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 Power Door Locks A power door lock switch is located on the driver’s and front passenger’s door panel. Push this switch to lock or unlock the doors and liftgate. NOTE: To prevent from locking the key in the vehicle, the power door lock switch will not operate when the key is in the ignition and either front door is open.
Page 34 32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Auto Lock Doors — If Equipped 2. Within 15 seconds, cycle the ignition switch be- tween LOCK and ON/RUN and then back to The auto door lock feature default condition is enabled. LOCK four times, ending up in the LOCK position When enabled, the door locks will lock automatically (do not start the engine).
Page 35 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 Automatic Unlock Doors On Exit Equipped/Personal Settings (Customer- Programmable Features)” in “Understanding Your In- The doors will unlock automatically if: strument Panel” for further information. • The Automatic Unlock Doors On Exit feature is en- •...
Page 36: Child-Protection Door Lock System - Rear Doors
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: 3. Repeat steps 1 and 2 for the opposite rear door. • If you do not hear the chime, it means that the system did not enter the programming mode and you will need to repeat the procedure.
Page 37: Power Windows - If Equipped
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 NOTE: For emergency exit with the system engaged, move the lock knob up (unlocked position), roll down the window, and open the door with the outside door handle. POWER WINDOWS — IF EQUIPPED Power Window Switches The window controls on the driver’s door trim panel control all the door windows.
Page 38: Auto-Down
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • For vehicles equipped with the EVIC, the power window switches will remain active for up to 10 minutes after the ignition switch is turned to the LOCK position. Opening either front door will cancel this feature.
Page 39: Window Lockout Switch
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 Window Lockout Switch The window lockout switch on the driver’s door allows you to disable the window controls on the rear passenger doors. To disable the window controls on the rear pas- senger doors, push the window LOCKOUT switch.
Page 40: Liftgate
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE LIFTGATE NOTE: The key that is used to start the vehicle is also used to lock or unlock the doors and open the liftgate. To unlock the liftgate, insert the key into the lock and turn to the right (manual lock models only).
Page 41: Occupant Restraint Systems
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 OCCUPANT RESTRAINT SYSTEMS WARNING! Some of the most important safety features in your • Driving with the liftgate open can allow poisonous vehicle are the restraint systems: exhaust gases into your vehicle. You and your •...
Page 42 40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Here are some simple steps you can take to minimize the 5. You should read the instructions provided with your risk of harm from a deploying air bag: child restraint to make sure that you are using it properly.
Page 43: Seat Belt Systems
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 ejection and the risk of injury caused by striking the WARNING! inside of the vehicle. Everyone in a motor vehicle should • Never place a rear-facing child restraint in front of be belted at all times. an air bag.
Page 44 42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE position the Seat Belt Reminder Light will turn on and driver and occupied outboard front seat passenger seat remain on until both outboard front seat belts are buck- belts are buckled. The driver should instruct all occu- led.
Page 45 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 BeltAlert can be activated or deactivated by your autho- will lock and reduce your risk of striking the inside of the rized dealer. FCA US LLC does not recommend deacti- vehicle or being thrown out of the vehicle. vating BeltAlert.
Page 46 44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) WARNING! (Continued) • It is dangerous to ride in a cargo area, inside or • Two people should never be belted into a single outside of a vehicle. In a collision, people riding in seat belt.
Page 47 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 WARNING! (Continued) WARNING! (Continued) • A seat belt that is buckled into the wrong buckle your strongest bones will take the force in a colli- will not protect you properly. The lap portion could sion.
Page 48 46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2. The seat belt latch plate is above the back of the front seat, and next to your arm in the rear seat (for vehicles equipped with a rear seat).
Page 49 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 Inserting Latch Plate Into Buckle Positioning The Lap Belt 4. Position the lap belt so that it is snug and lies low 5. Position the shoulder belt across the shoulder and across your hips, below your abdomen. To remove chest with minimal, if any slack so that it is comfort- slack in the lap belt portion, pull up on the shoulder able and not resting on your neck.
Page 50 48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 6. To release the seat belt, push the red button on the 3. Slide the latch plate upward over the folded webbing. buckle. The seat belt will automatically retract to its The folded webbing must enter the slot at the top of stowed position.
Page 51 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 NOTE: The adjustable upper shoulder belt anchorage is equipped with an Easy Up feature. This feature allows the shoulder belt anchorage to be adjusted in the upward position without pushing or squeezing the release but- ton.
Page 52 50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 1. Remove the mini-latch plate and regular latch plate 3. Route the shoulder belt to the inside of the right head from its stowed position in the right rear side trim restraint. panel.
Page 53 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 8. Position the shoulder belt on your chest so that it is 9. To release the seat belt, push the red button on the comfortable and not resting on your neck. The retrac- buckle.
Page 54 52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) proper restraint and will increase the risk of injury in a collision. • When reattaching the mini-latch plate and mini- buckle, ensure the seat belt webbing is not twisted. If the webbing is twisted, follow the preceding procedure to detach the mini-latch plate and mini- buckle, untwist the webbing, and reattach the mini-latch plate and mini-buckle.
Page 55 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 Seat Belt Extender is not required for a different occu- Seat Belts And Pregnant Women pant, it must be removed. WARNING! • ONLY use a Seat Belt Extender if it is physically required in order to properly fit the original seat belt system.
Page 56 54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Position the lap belt snug and low below the abdomen The pretensioners are triggered by the Occupant Re- and across the strong bones of the hips. Place the straint Controller (ORC). Like the air bags, the preten- shoulder belt across the chest and away from the neck.
Page 57 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 Restraints” section of this manual. The table below If the passenger seating position is equipped with an defines the type of feature for each seating position. ALR and is being used for normal usage, only pull the seat belt webbing out far enough to comfortably wrap around the occupant’s mid-section so as to not activate the ALR.
Page 58 56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE How To Disengage The Automatic Locking Mode WARNING! Unbuckle the combination lap/shoulder belt and allow it • Never place a rear-facing child restraint in front of to retract completely to disengage the Automatic Locking an air bag.
Page 59 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 the Active Head Restraints (AHR) to deploy. If a rear WARNING! (Continued) impact requires deployment, both the driver and front only used to install rear-facing or forward-facing passenger seat AHRs will be deployed. child restraints that have a harness for restraining When AHRs deploy during a rear impact, the front half the child.
Page 60 58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • All occupants, including the driver, should not operate a vehicle or sit in a vehicle’s seat until the head restraints are placed in their proper positions in order to minimize the risk of neck injury in the event of a collision.
Page 61 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 US LLC dealer must reset the AHRs on the driver’s and WARNING! (Continued) front passenger’s seat before driving. Personally attempt- as loose cargo could contact the Active Head Re- ing to reset the AHRs may result in damage to the AHRs straint during sudden stops.
Page 62: Supplemental Restraint System (Srs)
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Supplemental Side Air Bags WARNING! • Front and Side Impact Sensors Deployed AHRs are not able to best protect you in all • Seat Belt Pretensioners types of collisions. Have deployed AHRs reset by an authorized dealer immediately.
Page 63 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 WARNING! • Being too close to the steering wheel or instrument panel during Advanced Front Air Bag deployment could cause serious injury, including death. Air bags need room to inflate. Sit back, comfortably extending your arms to reach the steering wheel or instrument panel.
Page 64 62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Advanced Front Air Bag Features the driver or front passenger seat belt is buckled. The seat belt buckle switch may adjust the inflation rate of the The Advanced Front Air Bag system has multistage Advanced Front Air Bags.
Page 65 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 On the other hand, depending on the type and location of WARNING! (Continued) impact, Advanced Front Air Bags may deploy in crashes • Relying on the air bags alone could lead to more with little vehicle front-end damage but that produce a severe injuries in a collision.
Page 66 64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE way as the air bags inflate to their full size. The Advanced Supplemental Side Air Bags Front Air Bags fully inflate in less time than it takes to Your vehicle is equipped with two types of side air bags: blink your eyes.
Page 67 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 The SABs may help to reduce the risk of occupant injury 2. Supplemental Side Air Bag Inflatable Curtains (SABICs): Located above the side windows. The trim during certain side impacts and/or vehicle rollover covering the SABICs is labeled “SRS AIRBAG”...
Page 68 66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE SABICs may help reduce the risk of head or other injuries WARNING! to front and rear seat outboard occupants in certain side • Your vehicle is equipped with left and right impacts and/or vehicle rollover events, in addition to the injury reduction potential provided by the seat belts and Supplemental Side Air Bag Inflatable Curtains body structure.
Page 69 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 The SABICs and SABs (“Side Air Bags”) are designed to help keep you in position, away from inflating Side Air activate in certain side impacts and certain rollover Bags. To get the best protection from the Side Air Bags, events.
Page 70 68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The Side Air Bags will not deploy in all side collisions, WARNING! (Continued) including some collisions at certain angles, or some side properly. In some collisions, Side Air Bags won’t collisions that do not impact the area of the passenger deploy at all.
Page 71 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 faster-developing event may deploy the seat belt preten- deploy and unfold. The abrasions are similar to fric- sioners as well as the Side Air Bags on both sides of the tion rope burns or those you might get sliding along a vehicle.
Page 72 70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Do not drive your vehicle after the air bags have de- Enhanced Accident Response System ployed. If you are involved in another collision, the air In the event of an impact, if the communication network bags will not be in place to protect you.
Page 73 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 Enhanced Accident Response System Reset the OFF position or in the ACC position, the air bag Procedure system is not on and the air bags will not inflate. In order to reset the Enhanced Accident Response System The ORC contains a backup power supply system that functions after an event, the ignition switch must be may deploy the air bags even if the battery loses power or...
Page 74 72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE While the air bag system is designed to be maintenance WARNING! free, if any of the following occurs, have an authorized dealer service the air bag system immediately. Ignoring the Air Bag Warning Light in your instru- ment panel could mean you won’t have the air bags •...
Page 75 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 Maintaining Your Air Bag System WARNING! (Continued) • Do not attempt to modify any part of your air bag WARNING! system. The air bag may inflate accidentally or may • Modifications to any part of the air bag system not function properly if modifications are made.
Page 76 74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Event Data Recorder (EDR) These data can help provide a better understanding of the circumstances in which crashes and injuries occur. This vehicle is equipped with an event data recorder (EDR). The main purpose of an EDR is to record, in NOTE: EDR data are recorded by your vehicle only if a certain crash or near crash-like situations, such as an air non-trivial crash situation occurs;...
Page 77: Child Restraints
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 Child Restraints WARNING! Everyone in your vehicle needs to be buckled up at all In a collision, an unrestrained child can become a times, including babies and children. projectile inside the vehicle. The force required to Every state in the United States, and every Canadian hold even an infant on your lap could become so province, requires that small children ride in proper...
Page 78 76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE There are different sizes and types of restraints for NOTE: children from newborn size to the child almost large • For additional information, refer enough for an adult safety belt. Always check the child www.seatcheck.org or call 1–866–732–8243.
Page 79 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77 Summary Of Recommendations For Restraining Children In Vehicles Child Size, Height, Weight Or Age Recommended Type Of Child Restraint Infants and Children who are two years old or Either an Infant Carrier or a Convertible Toddlers younger and who have not reached the Child Restraint, facing rearward in the rear...
Page 80 78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Infants And Child Restraints WARNING! Safety experts recommend that children ride rear-facing • Never place a rear-facing child restraint in front of in the vehicle until they are two years old or until they an air bag.
Page 81 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 79 remain in a forward-facing child seat with a harness for WARNING! (Continued) as long as possible, up to the highest weight or height directions exactly when installing an infant or allowed by the child seat. child restraint.
Page 82 80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Children Too Large For Booster Seats 5. Can the child stay seated like this for the whole trip? Children who are large enough to wear the shoulder belt If the answer to any of these questions was “no,” then the comfortably, and whose legs are long enough to bend child still needs to use a booster seat in this vehicle.
Page 83 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 81 Recommendations For Attaching Child Restraints Restraint Type Combined Use any attachment method shown with an “X” Below Weight of the LATCH – Seat Belt Only LATCH – Seat Belt + Top Child + Child Lower Anchors Lower Anchors Tether Anchor...
Page 84 82 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lower Anchors And Tethers For CHildren Your vehicle is equipped with the child restraint anchor- (LATCH) Restraint System age system called LATCH, which stands for Lower Anchors and Tethers for CHildren. The LATCH system has three vehicle anchor points for installing LATCH- equipped child seats.
Page 85 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 83 LATCH Positions For Installing Child Restraints In This Vehicle • Lower Anchorage Symbol 2 anchorages per seating position • Top Tether Anchorage Symbol I n f o r ma t i o n P r o v i d e d b y :...
Page 86 84 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Frequently Asked Questions About Installing Child Seats With LATCH What is the weight limit (child’s weight 65 lbs (29.5 kg) Use the LATCH anchorage system until + weight of the child restraint) for us- the combined weight of the child and ing the LATCH anchorage system to the child restraint is 65 lbs (29.5 kg).
Page 87 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 85 Frequently Asked Questions About Installing Child Seats With LATCH Can two child restraints be attached Never “share” a LATCH anchorage using a common lower LATCH anchor- with two or more child restraints. If the age? center position does not have dedicated LATCH lower anchorages, use the seat...
Page 88 86 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Locating LATCH Anchorages The lower anchorages are round bars that are found at the rear of the seat cushion where it meets the seatback. They are just visible when you lean into the rear seat to install the child restraint.
Page 89 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 87 Locating Tether Anchorages There are tether strap anchorages behind each rear seating position located on the back of the seat. LATCH-compatible child restraint systems will be equipped with a rigid bar or a flexible strap on each side. Each will have a hook or connector to attach to the lower anchorage and a way to tighten the connection to the anchorage.
Page 90 88 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE restraints with flexible, webbing mounted lower attach- To Install A LATCH-Compatible Child Restraint ments can be installed in any rear seating position. If the selected seating position has a Switchable Auto- matic Locking Retractor (ALR) seat belt, stow the seat WARNING! belt, following the instructions below.
Page 91 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 89 3. Attach the lower hooks or connectors of the child How To Stow An Unused ALR Seat Belt: restraint to the lower anchorages in the selected seat- When using the LATCH attaching system to install a ing position.
Page 92 90 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Installing Child Restraints Using The Vehicle Seat WARNING! Belt • Improper installation of a child restraint to the The seat belts in the passenger seating positions are LATCH anchorages can lead to failure of the re- equipped with a Switchable Automatic Locking Retractor straint.
Page 93 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 91 Lap/Shoulder Belt Systems For Installing Child Restraints In This Vehicle • ALR = Switchable Automatic Locking Retractor • Top Tether Anchorage Symbol I n f o r ma t i o n P r o v i d e d b y :...
Page 94 92 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Frequently Asked Questions About Installing Child Restraints With Seat Belts What is the weight limit (child’s Weight limit of the Always use the tether anchor when using the seat weight + weight of the child re- Child Restraint belt to install a forward facing child restraint, up to straint) for using the Tether Anchor...
Page 95 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 93 Installing A Child Restraint With A Switchable 5. To lock the seat belt, pull down on the shoulder part of Automatic Locking Retractor (ALR) the belt until you have pulled all the seat belt webbing out of the retractor.
Page 96 94 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE strap. See the section “Installing Child Restraints WARNING! (Continued) Using the Top Tether Anchorage” for directions to tether strap of a rear-facing car seat to the tether attach a tether anchor. anchorage that is approved for that seating position, 9.
Page 97 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 95 1. Look behind the seating position where you plan to install the child restraint to find the tether anchorage. You may need to move the seat forward to provide better access to the tether anchorage. If there is no top tether anchorage for that seating position, move the child restraint to another position in the vehicle if one is available.
Page 98: Transporting Pets
96 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ENGINE BREAK-IN RECOMMENDATIONS WARNING! A long break-in period is not required for the engine and • An incorrectly anchored tether strap could lead to drivetrain (transmission and axle) in your vehicle. increased head motion and possible injury to the Drive moderately during the first 300 miles (500 km).
Page 99: Safety Tips
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 97 CAUTION! WARNING! • Do not leave children or animals inside parked Never use Non-Detergent Oil or Straight Mineral Oil in the engine or damage may result. vehicles in hot weather. Interior heat build-up may cause serious injury or death.
Page 100: Exhaust Gas
98 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Exhaust Gas WARNING! (Continued) • If it is necessary to sit in a parked vehicle with the WARNING! engine running, adjust your heating or cooling Exhaust gases can injure or kill. They contain carbon controls to force outside air into the vehicle.
Page 101: Safety Checks You Should Make Inside The Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 99 Safety Checks You Should Make Inside The have the system inspected at an authorized dealer as Vehicle soon as possible. This light will illuminate with a single chime when a fault with the Air Bag Warning Seat Belts Light has been detected, it will stay on until the fault Inspect the seat belt system periodically, checking for...
Page 102 100 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE unobstructed and that are firmly secured so that they WARNING! (Continued) cannot slip out of position and interfere with the pedals mats and other coverings will reduce the size of the or impair safe operation of your vehicle in other ways. pedal area and interfere with the pedals.
Page 103: Periodic Safety Checks You Should Make Outside
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 101 Periodic Safety Checks You Should Make Outside Door Latches The Vehicle Check for proper closing, latching, and locking. Tires Fluid Leaks Examine tires for excessive tread wear and uneven wear Check area under vehicle after overnight parking for fuel, patterns.
Page 104 I n f o r ma t i o n P r o v i d e d b y :...
Page 105: Understanding The Features Of Your Vehicle
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS ▫ Sun Visor “Slide-On-Rod” Feature — If MIRRORS ......108 Equipped .
Page 106 104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Folding Rear Seat .....160 VOICE COMMAND — IF EQUIPPED ..143 ▫...
Page 107 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 ▫ Headlights On With Wipers (Available With ▫ To Activate ......176 Automatic Headlights Only) .
Page 108 106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Using HomeLink .....189 ▫ Sunroof Maintenance ....193 ▫...
Page 109 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 ▫ Cargo Tie-Down Loops ....206 ▫ Rear Window Defroster ....209 ▫...
Page 110: Mirrors
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Day/Night Mirror A two-point pivot system allows for horizontal and vertical mirror adjustment. Adjust the mirror to center on the view through the rear window. Headlight glare can be reduced by moving the small control under the mirror to the night position (toward the rear of vehicle).
Page 111: Outside Mirror - Driver Side
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 NOTE: This feature is disabled when the vehicle is CAUTION! moving in reverse. To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean.
Page 112: Folding Outside Mirrors
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Mirrors WARNING! The power mirror control is located on the driver’s door Vehicles and other objects seen in the passenger side trim panel. convex mirror will look smaller and farther away than they really are. Relying too much on your passenger side convex mirror could cause you to collide with another vehicle or other object.
Page 113: Heated Mirrors - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 To adjust a mirror, turn the control wand toward the left Vanity Mirrors — If Equipped or right mirror positions indicated. Tilt the control wand To use the vanity mirror, rotate the sun visor down and in the direction you want the mirror to move.
Page 114: Sun Visor "Slide-On-Rod" Feature - If Equipped
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Sun Visor “Slide-On-Rod” Feature — If Equipped For Uconnect customer support: • U.S. residents - visit UconnectPhone.com or call 1-877- The sun visors may be extended out to provide more coverage of the side glass. 855-8400.
Page 115 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 Uconnect Phone. The Uconnect Phone allows up to seven (Uconnect Phone button and Voice Command mobile phones to be linked to the system. Only one button) that will enable you to access the system. linked (or paired) mobile phone can be used with the When you push the button you will hear the word system at a time.
Page 116: Operation
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • For certain operations, compound commands can be adjusted either from the radio volume control knob or from the steering wheel radio control (right switch), if used. For example, instead of saying “Setup” and then equipped.
Page 117 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 Voice Command Tree Pair (Link) Uconnect Phone To A Mobile Phone Refer to “Voice Tree” in this section. To begin using your Uconnect Phone, you must pair your compatible Bluetooth enabled mobile phone. Help Command To complete the pairing process, you will need to refer- If you need assistance at any prompt, or if you want to...
Page 118 116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE You will be asked to say a four-digit Personal Identifica- present in the vehicle, the Uconnect Phone will use the tion Number (PIN), which you will later need to enter priority three mobile phone when you make a call. You into your mobile phone.
Page 119 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 Call By Saying A Name Add Names To Your Uconnect Phonebook • Push the Phone button to begin. NOTE: Adding names to the Uconnect Phonebook is recommended when the vehicle is not in motion. •...
Page 120 118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 5. When prompted, recite the phone number for the names) and number entries from your mobile phone’s phonebook entry that you are adding. phonebook. Specific Bluetooth Phones with Phone Book Access Profile may support this feature. See Uconnect After you are finished adding an entry into the phone- website for supported phones.
Page 121 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 • Push the Phone downloaded names can be used. Until then, if avail- button to begin. able, the previously downloaded phonebook is avail- • After the “Ready” prompt and the following beep, say able for use.
Page 122 120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE mobile and a home number, but you can add “John entry that you wish to delete or you can say “List Doe’s” work number later using the “Phonebook Edit” Names” to hear a list of the entries in the phonebook feature.
Page 123 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 Delete/Erase “All” Uconnect Phonebook Entries List All Names In The Uconnect Phonebook To delete, or erase ALL Uconnect phonebook entries To hear a list of ALL names in the Uconnect phonebook using Voice Command: using Voice Commands: 1.
Page 124: Phone Call Features
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Phone Call Features Answer Or Reject An Incoming Call — Call Currently In Progress The following features can be accessed through the Uconnect Phone if the feature(s) are available on your If a call is currently in progress and you have another mobile service plan.
Page 125 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 entry you wish to call. The first call will be on hold indicating that the active and hold status of the two while the second call is in progress. To go back to the calls have switched.
Page 126 124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Phone button until you hear a double beep, indi- Redial cating that the two calls have been joined into one To redial the last number called from your mobile phone conference call. using Voice Command: Call Termination 1.
Page 127: Uconnect Phone Features
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 Call Continuation Uconnect Phone Features Call continuation is the progression of a phone call on the Language Selection Uconnect Phone after the vehicle ignition has been To change the language that the Uconnect Phone is using: switched to OFF.
Page 128 126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Emergency Assistance NOTE: • The emergency number dialed is based on the country If you are in an emergency and the mobile phone is reachable: where the vehicle is purchased (911 for the U.S. and Canada and 060 for Mexico).
Page 129 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 NOTE: You should program the desired Towing Assis- WARNING! tance phone number using the Voice Command system. To do this, push the Phone button and say “Setup,” To use your Uconnect Phone System in an emergency, followed by “Towing Assistance.”...
Page 130 128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Working With Automated Systems used for navigating through an automated customer service center menu structure, and to leave a number This method is used in instances where one generally has on a pager. to push numbers on the mobile phone keypad while navigating through an automated telephone system.
Page 131 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 • “Setup Confirmation Prompts Off” Barge In — Overriding Prompts The “Voice Command” button can be used when you Phone And Network Status Indicators wish to skip part of a prompt and issue your voice If available on the radio and/or on a premium display command immediately.
Page 132: Advanced Phone Connectivity
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Certain brands of mobile phones do not send the To un-mute the Uconnect Phone: dial ring to the Uconnect Phone to play it on the vehicle • Push the Voice Command button. audio system, so you will not hear it.
Page 133 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 • The Uconnect Phone will play the phone names of all Connect Or Disconnect Link Between The Uconnect Phone And Mobile Phone paired mobile phones in order from the highest to the lowest priority. To “Select” or “Delete” a paired phone Your mobile phone can be paired with many different being announced, push the Voice Command but-...
Page 134: Things You Should Know About Your Uconnect Phone
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The selected phone will be used for the next phone Things You Should Know About Your Uconnect call. If the selected phone is not available, the Uconnect Phone Phone will return to using the highest priority phone Uconnect Phone Tutorial present in or near (approximately within 30 ft.
Page 135 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 • Push the Voice Command • This will delete all phone pairing, phone book en- button and say the “Voice Training,” “System Training,” or “Start Voice tries, and other settings in all language modes. The Training”...
Page 136 134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Storing names in the phonebook when the vehicle is Performance is maximized under: not in motion is recommended. • Low-to-medium blower setting • It is not recommended to store similar sounding names •...
Page 137 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 Far End Audio Performance Recent Calls Audio quality is maximized under: If your phone supports “Automatic Phonebook Down- load,” Uconnect Phone can list your Outgoing, Incoming • Low-To-Medium Blower Setting and Missed Calls. •...
Page 138 136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Uconnect Phone will play the new text message for “Send.” Uconnect Phone will prompt you to say the you. name or number of the person you wish to send the message to. After reading a message, you can “Reply”...
Page 139 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 11. See you in 15 minutes. To turn Voice Text Reply incoming announcement on or off using Voice Command: 12. I am on my way. 1. Push the Phone button. 13. I’ll be late. 2.
Page 140 138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE I n f o r ma t i o n P r o v i d e d b y :...
Page 141 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 I n f o r ma t i o n P r o v i d e d b y :...
Page 142 140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE I n f o r ma t i o n P r o v i d e d b y :...
Page 143 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 Voice Commands Primary Alternate (s) Primary Alternate (s) zero call cancel confirmation prompts three continue four delete five dial download seven edit eight emergency nine English star (*) erase all plus (+) Espanol pound (#) Francais add location...
Page 144 142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Primary Alternate (s) Primary Alternate (s) home redial language return to main menu return or main menu list names select phone select list phones send mobile set up phone settings or phone set up mute towing assistance mute off...
Page 145: General Information
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 General Information VOICE COMMAND — IF EQUIPPED This device complies with Part 15 of the FCC rules and Voice Command System Operation RSS 210 of Industry Canada. Operation is subject to the following conditions: The Uconnect Voice Command system allows •...
Page 146 144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Pushing the Voice Command button while the sys- WARNING! tem is speaking is known as “barging in.” The system will be interrupted, and after the beep, you can add or Any voice commanded system should be used only change commands.
Page 147: Commands
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 To hear the first available Menu, push the Voice Com- Main Menu mand button and say “Help” or “Main Menu.” Start a dialogue by pushing the Voice Command but- ton. You may say “Main Menu” to switch to the main Commands menu.
Page 148 146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • “Menu Radio” (to switch to the radio menu) Radio AM • “Main Menu” (to switch to the main menu) To switch to the AM band, say “AM” or “Radio AM.” In this mode, you may say the following commands: Satellite Radio •...
Page 149 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 • “Play” (to play an Artist Name, Playlist Name, Album Disc Mode Name, Track Name, etc.) To switch to the disc mode, say “Disc.” In this mode, you may say the following commands: Bluetooth Streaming (BT) Mode •...
Page 150 148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Memo Mode – “Previous” (to play the previous memo) To switch to the voice recorder mode, say “Memo.” In – “Delete” (to delete a memo) this mode, you may say the following commands: –...
Page 151: Voice Training
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 • “Tutorial” 2. Repeat the words and phrases when prompted by Uconnect Voice. For best results, the “Voice Training” • “Voice Training” session should be completed when the vehicle is NOTE: Keep in mind that you have to push the Voice parked, engine running, all windows closed, and the Command button first and wait for the beep before...
Page 152: Power Seats - If Equipped
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! (Continued) • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. In a collision, people riding in these areas are more likely to be seriously injured or killed.
Page 153 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 Adjusting The Seat Forward Or Rearward WARNING! The seat can be adjusted both forward and rearward. • Adjusting a seat while driving may be dangerous. Push the seat switch forward or rearward. The seat will Moving a seat while driving could result in loss of move in the direction of the switch.
Page 154: Heated Seats - If Equipped
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Heated Seats — If Equipped minutes of continuous operation. At that time, the dis- play will change from HI to LO, indicating the change. On some models, the front driver and passenger seats When the LO-level heating is selected, the system auto- may be equipped with heaters in both the seat cushions matically turns the heater and the indicator light OFF...
Page 155: Manual Front Seat Adjustment
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 WARNING! (Continued) • Do not place anything on the seat or seatback that insulates against heat, such as a blanket or cushion. This may cause the seat heater to overheat. Sitting in a seat that has been overheated could cause serious burns due to the increased surface tempera- ture of the seat.
Page 156: Manual Seat Height Adjustment - If Equipped
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Manual Seat Height Adjustment — If Equipped WARNING! The driver’s seat height can be raised or lowered by using • Adjusting a seat while driving may be dangerous. a lever, located on the outboard side of the seat. Pull Moving a seat while driving could result in loss of upward on the lever to raise the seat height or push control which could cause a collision and serious...
Page 157: Manual Lumbar - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 Manual Lumbar — If Equipped Driver’s Seatback Recline The lumbar adjustment handle is located on the inboard To adjust the seatback, lift the lever located on the or outboard side of the seatback. Rotate the lever down- outboard side of the seat, lean back to the desired angle ward to increase the lumbar support or rotate the lever and release the lever.
Page 158: Head Restraints
156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! WARNING! Do not ride with the seatback reclined so that the The head restraints for all occupants must be prop- shoulder belt is no longer resting against your chest. erly installed and adjusted prior to operating the In a collision you could slide under the seat belt, vehicle or occupying a seat.
Page 159 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 When AHRs deploy during a rear impact, the front half of the head restraint extends forward to minimize the gap between the back of the occupant’s head and the AHR. This system is designed to help prevent or reduce the extent of injuries to the driver and front passenger in certain types of rear impacts.
Page 160 158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE For comfort the Active Head Restraints can be tilted forward and backward. To tilt the head restraint closer to the back of your head, pull forward on the bottom of the head restraint. Push rearward on the bottom of the head restraint to move the head restraint away from your head.
Page 161 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 • In the event of deployment of an Active Head Re- WARNING! (Continued) straint, refer to “Occupant Restraints/Resetting Active • Active Head Restraints may be deployed if they are Head Restraints (AHR)” in “Things To Know Before struck by an object such as a hand, foot or loose Starting Your Vehicle”...
Page 162: Folding Rear Seat
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Folding Rear Seat To provide additional storage area, each rear seatback can be folded forward. Pull the strap forward to fold the rear seatback flat. Folded Rear Seat To raise the seatback, pull the strap forward and lift the seatback into its upright position.
Page 163: Reclining Rear Seat - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 WARNING! WARNING! Be certain that the seatback is securely locked into Do not ride with the seatback reclined so that the position. If the seatback is not securely locked into shoulder belt is no longer resting against your chest. position the seat will not provide the proper stability In a collision you could slide under the seat belt and for child seats and/or passengers.
Page 164: To Open And Close The Hood
162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE TO OPEN AND CLOSE THE HOOD 2. Move the safety catch located under the front edge of the hood, near the center and raise the hood. To open the hood, two latches must be released. 1.
Page 165 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 Lift the hood prop rod, clipped to the right side (left side CAUTION! facing hood) of the engine compartment, to secure the hood in the open position. Place the hood prop at the To prevent possible damage: •...
Page 166: Lights
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE LIGHTS Multifunction Lever The multifunction lever controls the operation of the headlights, parking lights, turn signals, headlight beam selection, instrument panel light dimming, interior lights, the passing lights, and the fog lights. The multifunction lever is located on the left side of the steering column.
Page 167: Headlights And Parking Lights
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 Headlights And Parking Lights Automatic Headlights — If Equipped Turn the end of the multifunction lever to the first detent Turning the end of the multifunction lever to the third to turn on the parking lights. Turn the end of the lever to detent (AUTO), will activate the automatic headlight the second detent to turn on the headlights.
Page 168: Daytime Running Lights - If Equipped
166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE With the engine running and the multifunction lever in on the parking lights or the low beam headlights and pull the AUTO position, the headlights will turn on and turn out the end of the multifunction lever. off based on the surrounding light levels.
Page 169: Turn Signals
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 Turn Signals NOTE: If either light remains on and does not flash, or there is a very fast flash rate, check for a defective outside Move the multifunction lever up or down and the arrows light bulb.
Page 170: Flash-To-Pass
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Flash-To-Pass NOTE: The Headlights On with Wipers feature can be turned on or off using the Electronic Vehicle Information You can signal another vehicle with your headlights by Center (EVIC). Refer to “Electronic Vehicle Information lightly pulling the multifunction lever toward you.
Page 171: Map/Reading Lights
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169 Rotate the center portion of the lever upward to the last light off. The lights also come on when a door is opened detent to turn on the interior lighting. or the dimmer control is turned fully upward, past the second detent.
Page 172: Windshield Wipers And Washers
170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The lights will remain on until the switch is pushed a second time, so be sure they have been turned off before leaving the vehicle. They will not turn off automatically. WINDSHIELD WIPERS AND WASHERS The windshield wiper/washer control lever is located on the right side of the steering column.
Page 173: Windshield Wiper Operation
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 Windshield Wiper Operation CAUTION! Rotate the end of the lever upward to the second detent • Turn the windshield wipers off when driving past the intermittent settings for low-speed wiper opera- through an automatic car wash. Damage to the tion.
Page 174: Intermittent Wiper System
172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Intermittent Wiper System while the lever is pulled and for two wipe cycles after the lever is released, and then resume the intermittent inter- Use the intermittent wiper when weather conditions val previously selected. make a single wiping cycle, with a variable pause be- tween cycles, desirable.
Page 175: Mist Feature
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173 if the headlight switch is placed in the AUTO position. In NOTE: The mist feature does not activate the washer addition, the headlights will turn off when the wipers are pump; therefore, no washer fluid will be sprayed on the turned off if they were turned on by this feature.
Page 176: Tilt Steering Column
174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE TILT STEERING COLUMN This feature allows you to tilt the steering column upward or downward. The tilt steering column lever is located on the left side of the steering column, below the turn signal lever. Push down on the lever to unlock the steering column.
Page 177: Electronic Speed Control - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175 WARNING! Do not adjust the steering column while driving. Adjusting the steering column while driving or driv- ing with the steering column unlocked, could cause the driver to lose control of the vehicle. Failure to follow this warning may result in serious injury or death.
Page 178: To Activate
176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: In order to ensure proper operation, the Elec- WARNING! tronic Speed Control System has been designed to shut down if multiple Speed Control functions are operated at Leaving the Electronic Speed Control system on the same time.
Page 179: To Deactivate
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177 To Deactivate The drivers preferred units can be selected through the instrument panel settings if equipped. Refer to “Under- A soft tap on the brake pedal, pushing the CANCEL standing Your Instrument Panel” for more information. button, or normal brake pressure while slowing the The speed increment shown is dependant on the chosen vehicle will deactivate the Electronic Speed Control with-...
Page 180: To Accelerate For Passing
178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • If the button is continually pushed, the set speed will • If the button is continually pushed, the set speed will continue to increase until the button is released, then continue to decrease until the button is released, then the new set speed will be established.
Page 181: Parkview Rear Back Up Camera - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179 Using Electronic Speed Control On Hills PARKVIEW REAR BACK UP CAMERA — IF EQUIPPED The transmission may downshift on hills to maintain the vehicle set speed. Your vehicle may be equipped with the ParkView Rear Back Up Camera that allows you to see an on-screen NOTE: The Electronic Speed Control system maintains image of the rear surroundings of your vehicle whenever...
Page 182 180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE out of REVERSE unless the forward vehicle speed ex- Static grid lines will illustrate the width of the vehicle. ceeds 8 mph (13 km/h), the transmission is shifted into The static grid lines will show separate zones that will PARK or the vehicles ignition is cycled to the OFF help indicate the distance to the rear of the vehicle.
Page 183: Garage Door Opener - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 181 GARAGE DOOR OPENER — IF EQUIPPED CAUTION! HomeLink replaces up to three hand-held transmitters • To avoid vehicle damage, ParkView should only be that operate devices such as garage door openers, motor- used as a parking aid. The ParkView camera is ized gates, lighting or home security systems.
Page 184 182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE HomeLink Buttons/Overhead Consoles HomeLink Buttons/Sunvisor/Headliner NOTE: HomeLink is disabled when the Vehicle Security Alarm is active. I n f o r ma t i o n P r o v i d e d b y :...
Page 185: Before You Begin Programming Homelink
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 183 Before You Begin Programming HomeLink NOTE: • Erasing all channels should only be performed when Be sure that your vehicle is parked outside of the garage before you begin programming. programming HomeLink for the first time. Do not erase channels when programming additional buttons.
Page 186 184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Place the hand-held transmitter 1 to 3 inches (3 to 8 cm) away from the HomeLink button you wish to program while keeping the HomeLink indicator light in view. 3. Push and hold the HomeLink button you want to program while you push and hold the hand-held transmitter button.
Page 187 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 185 Firmly push and release the “LEARN” or “TRAIN- Reprogramming A Single HomeLink Button ING” button. On some garage door openers/devices (Rolling Code) there may be a light that blinks when the garage door To reprogram a channel that has been previously trained, opener/device is in the LEARN/TRAIN mode.
Page 188: Programming A Non-Rolling Code
186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Programming A Non-Rolling Code 5. Push and hold the programmed HomeLink button and observe the indicator light. For programming Garage Door Openers manufactured • If the indicator light stays on constantly, program- before 1995. ming is complete and the garage door/device should 1.
Page 189: Canadian/Gate Operator Programming
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 187 3. Without releasing the button proceed with “Program- It may be helpful to unplug the device during the cycling ming A Non-Rolling Code” step 2 and follow all process to prevent possible overheating of the garage remaining steps.
Page 190 188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Watch for the HomeLink indicator to change flash Reprogramming A Single HomeLink Button rates. When it changes, it is programmed. It may take (Canadian/Gate Operator) up to 30 seconds or longer in rare cases. The garage To reprogram a channel that has been previously trained, door may open and close while you are programming.
Page 191: Using Homelink
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 189 Using HomeLink Troubleshooting Tips To operate, push and release the programmed HomeLink If you are having trouble programming HomeLink, here button. Activation will now occur for the programmed are some of the most common solutions: device (i.e.
Page 192: General Information
190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE General Information WARNING! This device complies with FCC rules Part 15 and Industry • Vehicle exhaust contains carbon monoxide, a dan- Canada RSS-210. Operation is subject to the following gerous gas. Do not run your vehicle in the garage two conditions: while programming the transceiver.
Page 193: Power Sunroof - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 191 POWER SUNROOF — IF EQUIPPED WARNING! The power sunroof switch is located on the overhead • Never leave children alone in a vehicle, or with console. access to an unlocked vehicle. Never leave the Key Fob in or near the vehicle, or in a location acces- sible to children.
Page 194: Opening Sunroof - Express
192 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Opening Sunroof — Express position. The sunroof will close fully and stop automati- cally. This is called “Express Close.” During Express Push the switch rearward and release it within one-half Close operation, any other actuation of the switch will second.
Page 195: Venting Sunroof - Express
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 193 Venting Sunroof — Express open or partially open positions. This is a normal occur- rence and can be minimized. If the buffeting occurs with Push and release the Vent button within one half second the rear windows open, open the front and rear windows and the sunroof will open to the vent position.
Page 196: Electrical Power Outlets
194 UNDERSTANDING THE FEATURES OF YOUR VEHICLE For Vehicles Equipped With The EVIC The power sunroof switch will remain active for up to approximately ten minutes after the ignition switch is turned to the LOCK position. Opening either front door will cancel this feature.
Page 197 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 195 NOTE: To ensure proper operation a MOPAR knob and element must be used. CAUTION! • Do not exceed the maximum power of 160 Watts (13 Amps) at 12 Volts. If the 160 Watt (13 Amp) power rating is exceeded the fuse protecting the system will need to be replaced.
Page 198: Power Inverter - If Equipped
196 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! CAUTION! (Continued) • Accessories that draw higher power (i.e., coolers, To avoid serious injury or death: vacuum cleaners, lights, etc.) will degrade the bat- • Only devices designed for use in this type of outlet tery even more quickly.
Page 199 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 197 The power inverter is designed with built-in overload protection. If the power rating of 150 Watts is exceeded, the power inverter will automatically shut down. Once the electrical device has been removed from the outlet the inverter should automatically reset.
Page 200 198 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! CAUTION! • Many accessories that can be plugged in draw To avoid serious injury or death: • Do not use a three-prong adaptor. power from the vehicle’s battery, even when not in •...
Page 201: Cupholders
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 199 CUPHOLDERS There are two cupholders located in the back for the rear passengers. Your vehicle is equipped with four cupholders. There are two illuminated cupholders located in the front. Rear Cupholders Front Cupholders I n f o r ma t i o n P r o v i d e d b y :...
Page 202: Storage
200 UNDERSTANDING THE FEATURES OF YOUR VEHICLE STORAGE Glove Compartment And Storage Bin Located on the passenger side of the instrument panel are an upper storage bin and a lower glove compartment. Storage Bins 1 — Upper Storage Bin 2 — Lower Glove Compartment I n f o r ma t i o n P r o v i d e d b y :...
Page 203: Door Storage
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 201 To open the lower glove compartment, pull outward on Door Storage the release handle. The interior door panels are equipped with lower storage areas. Glove Compartment Front Door Storage I n f o r ma t i o n P r o v i d e d b y :...
Page 204: Console Features
202 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To open the upper storage compartment, push inward on the upper handle to unlatch the upper lid and lift the lid open. Rear Door Storage CONSOLE FEATURES The floor console contains both an upper and lower Upper Storage Compartment storage compartment.
Page 205: Cargo Area Features
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 203 WARNING! Do not operate this vehicle with a console compart- ment lid in the open position. Driving with the console compartment lid open may result in injury in a collision. CARGO AREA FEATURES Cargo Light The light is mounted in the headliner above the cargo area to illuminate the cargo area.
Page 206 204 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To install the Cargo Cover, insert either end of the cover Using the handle, pull the cover toward you and guide into one of the two notches located in the rear trim the rear cover posts into the guides located on both sides panels.
Page 207: Removable Load Floor
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 205 Removable Load Floor WARNING! The cargo area load floor is removable and can be In a collision a cargo cover loose in the vehicle could washed with mild soap and water. cause injury. It could fly around in a sudden stop and strike someone in the vehicle.
Page 208: Cargo Tie-Down Loops
206 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Cargo Tie-Down Loops WARNING! There are four tie-downs (D-rings) installed in the cargo • Cargo tie-down loops are not safe anchors for a area for securing cargo. child seat tether strap. In a sudden stop or collision a loop could pull loose and allow the child seat to come loose.
Page 209: Fold Down Speakers - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 207 Fold Down Speakers — If Equipped WARNING! (Continued) When the liftgate is open, the speakers can swing down • Place as much cargo as possible in front of the rear off the trim panel to face rearward, for tailgating and axle.
Page 210: Rear Window Features
208 UNDERSTANDING THE FEATURES OF YOUR VEHICLE REAR WINDOW FEATURES Rear Window Wiper/Washer The rear wiper/washer is controlled by a rotary switch located on the center portion of the control lever. The control lever is located on the right side of the steering column.
Page 211: Rear Window Defroster
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 209 NOTE: The rear wiper operates in an intermittent mode Rear Window Defroster only. The rear window defroster button is located on Rotate the center portion of the lever past the the climate controls mode control knob. Push the first detent to activate the rear washer.
Page 212: Roof Luggage Rack - If Equipped
210 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ROOF LUGGAGE RACK — IF EQUIPPED CAUTION! The crossbars and siderails are designed to carry the Failure to follow these cautions can cause damage to cargo on vehicles equipped with a luggage rack. The load the heating elements: must not exceed 150 lbs (68 kg), and should be uniformly •...
Page 213 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 211 The crossbars must also be secured in one of the seven improved satellite radio reception, place the rear cross- detent positions marked with an arrow on the siderails to bar in the second detent from the rear of the vehicle prevent movement.
Page 214 212 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! (Continued) WARNING! • Long loads which extend over the windshield, such Cargo must be securely tied before driving your as wood panels or surfboards, or loads with large vehicle. Improperly secured loads can fly off the frontal area should be secured to both the front and vehicle, particularly at high speeds, resulting in per- rear of the vehicle.
Page 215 UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS INSTRUMENT PANEL FEATURES ..217 ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) — IF EQUIPPED ....248 INSTRUMENT CLUSTER .
Page 216 214 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Display Units Of Measure In ... . .254 ▫ Hill Start Assist (HSA) — If Equipped ..257 ▫ Display Units In ..... .257 Personal Settings (Customer-Programmable Features) .
Page 217 UNDERSTANDING YOUR INSTRUMENT PANEL 215 ▫ INFO Button — DISC Mode For MP3/WMA UCONNECT 130 WITH SATELLITE RADIO . . .290 Play .......274 ▫...
Page 218 216 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ List Or Browse Mode ....310 RADIO OPERATION AND MOBILE DEVICES . .315 ▫ Bluetooth Streaming Audio (BTSA) ..312 CLIMATE CONTROLS .
Page 219: Instrument Panel Features
UNDERSTANDING YOUR INSTRUMENT PANEL 217 INSTRUMENT PANEL FEATURES 1 — Air Outlet 5 — Storage Bin 9 — Heated Seat Switch – If Equipped 2 — Demisters 6 — Glove Compartment 10 — Hazard Warning Flasher 3 — Instrument Cluster 7 —...
Page 220: Instrument Cluster
218 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER I n f o r ma t i o n P r o v i d e d b y :...
Page 221 UNDERSTANDING YOUR INSTRUMENT PANEL 219 1. Speedometer properly reset, or that the door jamb sticker is accurate if • The Speedometer shows the vehicle speed in miles the odometer must be reset at zero. per hour (MPH) and kilometers per hour (km/h). Odometer Display / Trip Odometer Display This 2.
Page 222 220 UNDERSTANDING YOUR INSTRUMENT PANEL 4. Electronic Vehicle Information Center (EVIC) — If CAUTION! Equipped / Odometer Display / Trip Odometer Dis- play Driving with a hot engine cooling system could damage your vehicle. If the temperature gauge reads Electronic Vehicle Information Center (EVIC) — If “H”...
Page 223 UNDERSTANDING YOUR INSTRUMENT PANEL 221 Message Display Area LoW tirE When the appropriate conditions exist, the following When the appropriate condition exists, the odometer odometer messages will display: display will toggle between LoW and tirE for three cycles. door ......Door Ajar gASCAP gATE .
Page 224 222 UNDERSTANDING YOUR INSTRUMENT PANEL damaged, a “noFUSE” message will display in the odom- 1. Turn the ignition switch to the ON/RUN position (do eter display area. Refer to “Fuses” in “Maintaining Your not start the engine). Vehicle” for further information on fuses and fuse loca- 2.
Page 225: Warning And Indicator Lights
UNDERSTANDING YOUR INSTRUMENT PANEL 223 WARNING AND INDICATOR LIGHTS All active telltales will display first if applicable. The system check menu may appear different based upon IMPORTANT: The warning / indicator light switches on equipment options and current vehicle status. Some in the instrument panel together with a dedicated mes- telltales are optional and may not appear.
Page 226: Red Telltale Indicator Lights
224 UNDERSTANDING YOUR INSTRUMENT PANEL Red Telltale Indicator Lights Seat Belt Reminder Warning Light Red Telltale What It Means Light Seat Belt Reminder Warning Light When the ignition switch is first turned to ON/RUN, this light will turn on for four to eight seconds as a bulb check.
Page 227 UNDERSTANDING YOUR INSTRUMENT PANEL 225 Air Bag Warning Light Red Telltale What It Means Light Air Bag Warning Light This light will turn on for four to eight seconds as a bulb check when the ignition switch is first turned to ON/RUN. If the light is either not on during starting, stays on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible.
Page 228 226 UNDERSTANDING YOUR INSTRUMENT PANEL Brake Warning Light Red Telltale What It Means Light Brake Warning Light This light monitors various brake functions, including brake fluid level and parking brake application. If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the anti-lock brake system reser- voir.
Page 229 UNDERSTANDING YOUR INSTRUMENT PANEL 227 The light will remain on until the cause is corrected. Brake Warning Light will turn on along with the ABS Light. Immediate repair to the ABS system is required. NOTE: The light may flash momentarily during sharp cornering maneuvers, which change fluid level condi- Operation of the Brake Warning Light can be checked by tions.
Page 230 228 UNDERSTANDING YOUR INSTRUMENT PANEL Vehicle Security Warning Light — If Equipped Red Telltale What It Means Light Vehicle Security Warning Light This light will flash at a fast rate for approximately 15 seconds when the vehicle security alarm is arming, and then will flash slowly until the vehicle is disarmed. Oil Pressure Warning Light Red Telltale What It Means...
Page 231 UNDERSTANDING YOUR INSTRUMENT PANEL 229 Engine Temperature Warning Light Red Warning What It Means Light Engine Temperature Warning Light This light warns of an overheated engine condition. As engine coolant temperatures rise and the gauge approaches H, this indicator will illuminate and a single chime will sound after reaching a set threshold.
Page 232 230 UNDERSTANDING YOUR INSTRUMENT PANEL Oil Temperature Warning Light Red Telltale What It Means Light Oil Temperature Warning Light This telltale indicates engine oil temperature is high. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. Charging System Warning Light Red Telltale What It Means...
Page 233 UNDERSTANDING YOUR INSTRUMENT PANEL 231 Red Telltale What It Means Light If jump starting is required, refer to “Jump Starting Procedures” in “What To Do In Emer- gencies.” Electronic Throttle Control (ETC) Warning Light Red Telltale What It Means Light Electronic Throttle Control (ETC) Warning Light This light informs you of a problem with the Electronic Throttle Control (ETC) system.
Page 234: Yellow Telltale Indicator Lights
232 UNDERSTANDING YOUR INSTRUMENT PANEL Red Telltale What It Means Light RUN and remain on briefly as a bulb check. If the light does not come on during starting, have the system checked by an authorized dealer. Yellow Telltale Indicator Lights Engine Check/Malfunction Indicator Light (MIL) Yellow Telltale What It Means...
Page 235 UNDERSTANDING YOUR INSTRUMENT PANEL 233 Yellow Telltale What It Means Light Certain conditions, such as a loose or missing gas cap, poor quality fuel, etc., may illuminate the light after engine start. The vehicle should be serviced if the light stays on through sev- eral typical driving styles.
Page 236 234 UNDERSTANDING YOUR INSTRUMENT PANEL Tire Pressure Monitoring Indicator Light Yellow Telltale What It Means Light Tire Pressure Monitoring Indicator Light The warning light switches on and a message is displayed to indicate that the tire pressure is lower than the recommended value and/or that slow pressure loss is occurring. In these cases, optimal tire duration and fuel consumption may not be guaranteed.
Page 237 UNDERSTANDING YOUR INSTRUMENT PANEL 235 IMPORTANT: Do not continue driving with one or more Accordingly, when the low tire pressure telltale illumi- flat tires as handling may be compromised. Stop the nates, you should stop and check your tires as soon as vehicle, avoiding sharp braking and steering.
Page 238 236 UNDERSTANDING YOUR INSTRUMENT PANEL illuminated. This sequence will continue upon subse- CAUTION! (Continued) quent vehicle start-ups as long as the malfunction exists. equipped on your vehicle. Undesirable system opera- When the malfunction indicator is illuminated, the sys- tion or sensor damage may result when using re- tem may not be able to detect or signal low tire pressure placement equipment that is not of the same size, as intended.
Page 239 UNDERSTANDING YOUR INSTRUMENT PANEL 237 Electronic Stability Control (ESC) OFF Indicator Light — If Equipped Yellow Telltale What It Means Light Electronic Stability Control (ESC) OFF Indicator Light This light indicates the Electronic Stability Control (ESC) is off. I n f o r ma t i o n P r o v i d e d b y :...
Page 240 238 UNDERSTANDING YOUR INSTRUMENT PANEL Electronic Stability Control (ESC) Indicator Light — If Equipped Yellow Telltale What It Means Light Electronic Stability Control (ESC) Indicator Light The “ESC Indicator Light” in the instrument cluster will come on when the ignition switch is turned to the ON/RUN position.
Page 241 UNDERSTANDING YOUR INSTRUMENT PANEL 239 Anti-Lock Brake (ABS) Indicator Light Yellow Telltale What It Means Light Anti-Lock Brake (ABS) Indicator Light This light monitors the Anti-Lock Brake System (ABS). The light will turn on when the igni- tion switch is placed in the ON/RUN position and may stay on for as long as four seconds. If the ABS light remains on or turns on while driving, then the Anti-Lock portion of the brake system is not functioning and service is required.
Page 242 240 UNDERSTANDING YOUR INSTRUMENT PANEL Low Fuel Warning Indicator Light Yellow Telltale What It Means Light Low Fuel Warning Indicator Light When the fuel level reaches approximately 2.8 gal (10.6 L), this light will turn on and a single chime will sound. 4WD! Warning Light —...
Page 243 UNDERSTANDING YOUR INSTRUMENT PANEL 241 Loose Fuel Filler Cap Indicator Light — If Equipped Yellow Telltale What It Means Light Loose Fuel Filler Cap Indicator Light This light will illuminate when fuel filler cap is loose. Properly close the filler cap to disen- gage the light.
Page 244 242 UNDERSTANDING YOUR INSTRUMENT PANEL Transmission Temperature Indicator Light Red Telltale What It Means Light Transmission Temperature Indicator Light This light indicates that the transmission fluid temperature is running hot. This may occur with severe usage, such as trailer towing. If this light turns on, safely pull over and stop them ve- hicle.
Page 245: Green Telltale Indicator Lights
UNDERSTANDING YOUR INSTRUMENT PANEL 243 Green Telltale Indicator Lights Turn Signal Indicator Lights Green Tell- What It Means tale Light Turn Signal Indicator Lights The instrument cluster arrow will flash independently for the LEFT or RIGHT turn signal as se- lected, as well as the exterior turn signal lamp(s) (front and rear) as selected when the multi- function lever is moved down (LEFT) or up (RIGHT).
Page 246 244 UNDERSTANDING YOUR INSTRUMENT PANEL Park/Headlight ON Indicator Light Green Telltale What It Means Light Park/Headlight ON Indicator Light This indicator will illuminate when the park lights or headlights are turned on. Front Fog Indicator Light — If Equipped Green Telltale What It Means Light Front Fog Indicator Light...
Page 247: Blue Telltale Indicator Light
UNDERSTANDING YOUR INSTRUMENT PANEL 245 Blue Telltale Indicator Light High Beam Indicator Light Blue Telltale What It Means Light High Beam Indicator Light This indicator shows that the high beam headlights are on. Push the multifunction control lever away from you to switch the headlights to high beam. Pull the lever toward you to switch the headlights back to low beam.
Page 248: Mini-Trip Computer - If Equipped
246 UNDERSTANDING YOUR INSTRUMENT PANEL Hill Descent Indicator Light — If Equipped White Tell- What It Means tale Light Hill Descent Indicator Light This indicator shows when the Hill Descent Control (HDC) feature is turned on. The lamp will be on solid when HDC is armed. HDC can only be armed when the transfer case is in the “4WD LOW”...
Page 249: Control Buttons
UNDERSTANDING YOUR INSTRUMENT PANEL 247 Control Buttons RESET Button To reset the display shown, turn the ignition switch to the ON position, then push and hold the RESET button located on the steering wheel. The following displays can be reset or changed: •...
Page 250: Electronic Vehicle Information Center (Evic) - If Equipped
248 UNDERSTANDING YOUR INSTRUMENT PANEL ELECTRONIC VEHICLE INFORMATION CENTER The EVIC consists of the following: (EVIC) — IF EQUIPPED • System Status The Electronic Vehicle Information Center (EVIC) fea- • Units tures a driver-interactive display that is located in the •...
Page 251 UNDERSTANDING YOUR INSTRUMENT PANEL 249 The system allows the driver to select information by MENU Button pushing the following buttons mounted on the steering Push and release the MENU button to scroll wheel: through the main menus (Fuel Economy, Warn- ings, Timer, Units, System, Personal Settings) or to exit submenus.
Page 252 250 UNDERSTANDING YOUR INSTRUMENT PANEL • Personal Settings Not Avail. — Vehicle is not in PARK DOWN Button (automatic transmission), or vehicle is in motion Push and release the DOWN button to scroll (manual transmission). downward through the submenus. • Door Ajar (with vehicle graphic showing which door is open.
Page 253: Engine Oil Change Indicator System - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 251 • Remote Start Aborted — Fuel Low indicator system is duty-cycle based, which means the engine oil change interval may fluctuate dependent upon • Remote Start Aborted — System Fault your personal driving style. • Key In Ignition Unless reset, this message will continue to display each •...
Page 254: Evic Functions
252 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: If the indicator message illuminates when you only occur if a resettable function is currently being start the vehicle, the oil change indicator system did not displayed. To reset all resettable functions, push and reset.
Page 255: Distance To Empty (Dte)
UNDERSTANDING YOUR INSTRUMENT PANEL 253 prompted in the EVIC display to reset). When the fuel significant amount of fuel to the vehicle will turn off the economy is reset, the display will read “RESET” or show LOW FUEL text and a new DTE value will be dis- dashes for two seconds.
Page 256: Display Units Of Measure In
254 UNDERSTANDING YOUR INSTRUMENT PANEL Upon reset, all digits will change to zeros, and time will Use the RIGHT button to display one of the following start incrementing again if the ignition switch is in RUN choices: or START. Language Display Units Of Measure In When in this display, you may select different languages To make your selection, push and release the RIGHT...
Page 257: Auto Unlock On Exit
UNDERSTANDING YOUR INSTRUMENT PANEL 255 and hold the RIGHT arrow button when in this display button. Push and hold the RIGHT arrow button when in until “ON” or “OFF” appears to make your selection. this display until “Driver’s Door 1st” or “All Doors” appears to make your selection.
Page 258: Headlamp Off Delay
256 UNDERSTANDING YOUR INSTRUMENT PANEL Headlamp Off Delay NOTE: Turning the headlights on during the daytime causes the instrument panel lights to dim. To increase the When this feature is selected the driver can choose to brightness, refer to “Lights” in “Understanding The have the headlights remain on for 0, 30, 60, or 90 seconds Features Of Your Vehicle.”...
Page 259: Hill Start Assist (Hsa) - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 257 RIGHT arrow button when in this display until “OFF,” Automatic Compass Calibration “30 sec,” “60 sec,” or “90 sec.” appears to make your This compass is self-calibrating, which eliminates the selection. need to set the compass manually. When the vehicle is new, the compass may appear erratic, and the EVIC will Hill Start Assist (HSA) —...
Page 260: Manual Compass Calibration
258 UNDERSTANDING YOUR INSTRUMENT PANEL Manual Compass Calibration 5. Complete one or more 360–degree turns (in an area free from large metal or metallic objects) until the If the compass appears erratic and the “CAL” indicator “CAL” indicator turns off. The compass will now does not appear in the EVIC display, you must put the function normally.
Page 261 UNDERSTANDING YOUR INSTRUMENT PANEL 259 1. Turn the ignition switch ON. 2. Push and hold the COMPASS button for approxi- mately two seconds. 3. Push and release the DOWN button until “Compass Variance” message and the last variance zone number displays in the EVIC.
Page 262: Uconnect 230 - Am/Fm Stereo Radio And 6-Disc Cd/Dvd Changer
260 UNDERSTANDING YOUR INSTRUMENT PANEL UCONNECT 230 – AM/FM STEREO RADIO AND Operating Instructions — Radio Mode 6–DISC CD/DVD CHANGER (MP3/WMA AUX NOTE: The ignition switch must be in the ON or ACC JACK) position to operate the radio. Power Switch/Volume Control (Rotary) Push the ON/VOLUME control knob to turn on the radio.
Page 263 UNDERSTANDING YOUR INSTRUMENT PANEL 261 SEEK Buttons If your vehicle is not equipped with or this feature is not available on your vehicle, a “Not Equipped With Push and release the SEEK buttons to search for the next Uconnect Phone” message will display on the radio listenable station in AM/FM mode.
Page 264 262 UNDERSTANDING YOUR INSTRUMENT PANEL Clock Setting Procedure INFO Button Push the INFO button for an RDS station (one with call 1. Push and hold the TIME button until the hours blink. letters displayed). The radio will return a Radio Text 2.
Page 265 UNDERSTANDING YOUR INSTRUMENT PANEL 263 Push the rotary TUNE/SCROLL control knob a second Push the rotary TUNE/SCROLL control knob again to time and MID will display. Turn the TUNE/SCROLL exit setting tone, balance, and fade. control knob to the right or left to increase or decrease the MUSIC TYPE Button mid-range tones.
Page 266 264 UNDERSTANDING YOUR INSTRUMENT PANEL 16-Digit Character 16-Digit Character Program Type Program Type Display Display Classical Classicl Religious Talk Rel Talk Classic Rock Cls Rock Rock Rock College College Soft Soft Country Country Soft Rock Soft Rck Foreign Language Language Soft Rhythm and Blues Soft R &...
Page 267 UNDERSTANDING YOUR INSTRUMENT PANEL 265 • DISC Play/Pause — If a preset button is activated while in the Music Type (Program Type) mode, the Music Type mode will be You can toggle between playing the DVD and exited and the radio will tune to the preset station. pausing the DVD by pushing the SELECT SETUP Button button (if equipped).
Page 268 266 UNDERSTANDING YOUR INSTRUMENT PANEL • Player Defaults — Selecting this item will allow the NOTE: user to scroll through the following items and set • The available selections for each of the above entries defaults according to customer preference. varies depending upon the disc.
Page 269 UNDERSTANDING YOUR INSTRUMENT PANEL 267 the TUNE/SCROLL control knob to scroll up and down Audio DRC — If Equipped to select the number and then push to select. Selecting this item allows you to limit maximum audio Subtitle Language — If Equipped dynamic range.
Page 270 268 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: The user will have to set these defaults before You may add a second station to each pushbutton by loading a disc. If changes are made to these settings after repeating the above procedure with this exception: Push a disc is loaded, changes will not be effective.
Page 271: Operation Instructions - Disc Mode For Cd And Mp3/Wma Audio Play, Dvd - Video
UNDERSTANDING YOUR INSTRUMENT PANEL 269 DISC Button CAUTION! (Continued) Pushing the DISC button will allow you to switch from “Disc Hot” and shut off until a safe temperature is AM/FM modes to Disc modes. reached. This shutdown is necessary to protect the optics of the DVD player and other radio internal Operation Instructions —...
Page 272 270 UNDERSTANDING YOUR INSTRUMENT PANEL SEEK Button (CD MODE) CAUTION! Push the right SEEK button for the next selection on the This CD player will accept 4–3/4 inch (12 cm) discs CD. Push the left SEEK button to return to the beginning only.
Page 273: Notes On Playing Mp3/Wma Files
UNDERSTANDING YOUR INSTRUMENT PANEL 271 RW/FF (CD MODE) Supported Medium Formats (File Systems) Push and hold FF (Fast Forward) and the CD player will The medium formats supported by the radio are ISO 9660 begin to fast forward until FF is released, or RW or Level 1 and Level 2 and includes the Joliet extension.
Page 274 272 UNDERSTANDING YOUR INSTRUMENT PANEL Multisession disc formats are supported by the radio. When using the MP3/WMA encoder to compress audio Multisession discs may contain combinations of normal data to an MP3/WMA file, the bit rate and sampling CD audio tracks and computer files (including MP3/ frequencies in the following table are supported.
Page 275: List Button - Disc Mode For Mp3/Wma Play
UNDERSTANDING YOUR INSTRUMENT PANEL 273 Loading times for playback of MP3/WMA files may be Sampling Fre- Bit Rate (kbps) affected by the following: Specification quency (kHz) • Media - CD-RW media may take longer to load than 44.1 and 48 48, 64, 96, 128, 160, 192 VBR CD-R media...
Page 276: Info Button - Disc Mode For Mp3/Wma Play
274 UNDERSTANDING YOUR INSTRUMENT PANEL folder by pushing the TUNE/SCROLL control knob will Operation Instructions — Auxiliary Mode begin playing the files contained in that folder (or the The auxiliary (AUX) jack is an audio input jack which next folder in sequence if the selection does not contain allows the user to plug in a portable device such as an playable files).
Page 277 UNDERSTANDING YOUR INSTRUMENT PANEL 275 SCAN Button (Auxiliary Mode) Operating Instructions (Voice Command System) — If Equipped No function. Refer to “Voice Command” for further details. EJECT Button (Auxiliary Mode) Operating Instructions (Uconnect Phone) — If Equipped No function. Refer to “Uconnect Phone” for further details. Dolby TIME Button (Auxiliary Mode) Manufactured under license from Dolby Laboratories.
Page 278: Uconnect (Satellite Radio) - If Equipped
276 UNDERSTANDING YOUR INSTRUMENT PANEL intended for home and other limited viewing uses only, System Activation unless otherwise authorized by Macrovision. Reverse Sirius Satellite Radio service is pre-activated, and you engineering or disassembly is prohibited. may begin listening immediately to the one year of audio service that is included with the factory-installed satellite radio system in your vehicle.
Page 279 UNDERSTANDING YOUR INSTRUMENT PANEL 277 To access the ESN/SID, refer to the following steps: decreased performance. Larger luggage items such as bikes should be placed as far rearward as possible, within ESN/SID Access the loading design of the rack. Do not place items directly With the ignition switch in the ON/RUN or ACC posi- on or above the antenna.
Page 280 278 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions — Uconnect (Satellite) INFO Button Mode Pushing the INFO button will cycle the display informa- tion between Artist, Song Title, and Composer (if avail- NOTE: The ignition switch must be in the ON/RUN or able).
Page 281 UNDERSTANDING YOUR INSTRUMENT PANEL 279 MUSIC TYPE Button SETUP Button Pushing this button once will turn on the Music Type Pushing the SETUP button allows you to select the mode for five seconds. Pushing the MUSIC TYPE button following items: or turning the TUNE/SCROLL control knob within five •...
Page 282: Uconnect 430/430N Cd/Dvd/Hdd/Nav
280 UNDERSTANDING YOUR INSTRUMENT PANEL You may add a second channel to each pushbutton by UCONNECT 430/430N CD/DVD/HDD/NAV — IF repeating the above procedure with this exception: Push EQUIPPED the SET button twice and SET 2 will show in the display Refer to your Uconnect Supplement Manual for detailed window.
Page 283: Uconnect 130
UNDERSTANDING YOUR INSTRUMENT PANEL 281 UCONNECT 130 Power Switch/Volume Control (Rotary) Push the ON/VOLUME control knob to turn on the radio. Push the ON/VOLUME control knob a second time to turn off the radio. Electronic Volume Control The electronic volume control turns continuously (360 degrees) in either direction, without stopping.
Page 284 282 UNDERSTANDING YOUR INSTRUMENT PANEL another selection. Holding either button will bypass 5. To exit, push any button/knob, or wait five seconds. stations without stopping, until you release it. RW/FF TIME Button Pushing the RW (Rewind) or FF (Fast Forward) buttons Push the TIME button to alternate display of the time and causes the tuner to search for the next frequency in the radio frequency.
Page 285 UNDERSTANDING YOUR INSTRUMENT PANEL 283 Push the rotary TUNE/SCROLL control knob a second Push the rotary TUNE/SCROLL control knob again to time and MID will display. Turn the TUNE/SCROLL exit setting tone, balance, and fade. control knob to the right or left to increase or decrease the AM/FM Button mid-range tones.
Page 286: Operation Instructions - Cd Mode For Cd And Mp3 Audio Play
284 UNDERSTANDING YOUR INSTRUMENT PANEL display window. Each button can be set for SET 1 and Operation Instructions — CD MODE For CD And SET 2 in both AM and FM. This allows a total of 12 AM MP3 Audio Play and 12 FM stations to be stored into pushbutton memory.
Page 287 UNDERSTANDING YOUR INSTRUMENT PANEL 285 If you insert a disc with the ignition ON and the radio CAUTION! (Continued) ON, the unit will switch from radio to CD mode and • Dual-media disc types (one side is a DVD, the begin to play when you insert the disc.
Page 288: Notes On Playing Mp3 Files
286 UNDERSTANDING YOUR INSTRUMENT PANEL SEEK Button AM/FM Button Push the right SEEK button for the next selection on the Push the button to select either AM or FM mode. CD. Push the left SEEK button to return to the beginning SET/RND Button (Random Play Button) of the current selection, or return to the beginning of the Push this button while the CD is playing to activate...
Page 289 UNDERSTANDING YOUR INSTRUMENT PANEL 287 Supported Media (Disc Types) display the file name and folder name, and will assign a number instead. With a maximum number of files, The MP3 file recording media supported by the radio are exceeding 20 folders will result in this display. With CDDA, CD-R, CD-RW, MP3, and CDDA+MP3.
Page 290 288 UNDERSTANDING YOUR INSTRUMENT PANEL Supported MP3 File Formats MPEG Specifi- Sampling Fre- Bit Rate (kbps) cation quency (kHz) The radio will recognize only files with the *.MP3 exten- sion as MP3 files. Non-MP3 files named with the *.MP3 MPEG-1 Audio 48, 44.1, 32 320, 256, 224, extension may cause playback problems.
Page 291: Operation Instructions - Auxiliary Mode
UNDERSTANDING YOUR INSTRUMENT PANEL 289 Playback Of MP3 Files Operation Instructions — Auxiliary Mode When a medium containing MP3 data is loaded, the The auxiliary (AUX) jack is an audio input jack, which radio checks all files on the medium. If the medium allows the user to plug in a portable device, such as an contains a lot of folders or files, the radio will take more MP3 player, or iPod, and utilize the vehicle’s audio...
Page 292: Uconnect 130 With Satellite Radio
290 UNDERSTANDING YOUR INSTRUMENT PANEL UCONNECT 130 WITH SATELLITE RADIO Power Switch/Volume Control (Rotary) Push the ON/VOLUME control knob to turn on the radio. Push the ON/VOLUME control knob a second time to turn off the radio. Electronic Volume Control The electronic volume control turns continuously (360 degrees) in either direction, without stopping.
Page 293 UNDERSTANDING YOUR INSTRUMENT PANEL 291 another selection. Holding either button will bypass Phone Button Uconnect Phone — If Equipped stations without stopping, until you release it. Push this button to operate the Uconnect Phone feature (if equipped). Refer to “Uconnect Phone” in “Under- Voice Command System (Radio) —...
Page 294 292 UNDERSTANDING YOUR INSTRUMENT PANEL 3. After adjusting the hours, push the right side TUNE/ INFO Button SCROLL control knob to set the minutes. The minutes Push the INFO button for an RDS station (one with call will begin to blink. letters displayed).
Page 295 UNDERSTANDING YOUR INSTRUMENT PANEL 293 Push the rotary TUNE/SCROLL control knob a second Push the rotary TUNE/SCROLL control knob again to time and MID will display. Turn the TUNE/SCROLL exit setting tone, balance, and fade. control knob to the right or left to increase or decrease the MUSIC TYPE Button mid-range tones.
Page 296 294 UNDERSTANDING YOUR INSTRUMENT PANEL 16-Digit Character 16-Digit Character Program Type Program Type Display Display Classical Classicl Religious Talk Rel Talk Classic Rock Cls Rock Rock Rock College College Soft Soft Country Country Soft Rock Soft Rck Foreign Language Language Soft Rhythm and Blues Soft R&B Information...
Page 297 UNDERSTANDING YOUR INSTRUMENT PANEL 295 If a preset button is activated while in the Music Type SET/RND Button — To Set The Pushbutton (Program Type) mode, the Music Type mode will be Memory exited and the radio will tune to the preset station. When you are receiving a station that you wish to commit to pushbutton memory, push the SET/RND SETUP Button...
Page 298: Operation Instructions - Cd Mode For Cd And Mp3 Audio Play
296 UNDERSTANDING YOUR INSTRUMENT PANEL • This radio is capable of playing compact discs (CD), Every time a preset button is used, a corresponding button number will display. recordable compact discs (CD-R), rewritable compact discs (CD-RW), compact discs with MP3 tracks and Buttons 1 - 6 multisession compact discs with CD and MP3 tracks.
Page 299 UNDERSTANDING YOUR INSTRUMENT PANEL 297 If you have ejected a disc and have not removed it within CAUTION! 10 seconds, it will be reloaded. If the CD is not removed, • This CD player will accept 4–3/4 inch (12 cm) discs the radio will reinsert the CD but will not play it.
Page 300: Notes On Playing Mp3 Files
298 UNDERSTANDING YOUR INSTRUMENT PANEL RW/FF Notes On Playing MP3 Files Push and hold FF (Fast Forward) and the CD player will The radio can play MP3 files; however, acceptable MP3 begin to fast forward until FF is released or RW or file recording media and formats are limited.
Page 301 UNDERSTANDING YOUR INSTRUMENT PANEL 299 The radio uses the following limits for file systems: Multi-session disc formats are supported by the radio. Multi-session discs may contain combinations of normal • Maximum number of folder levels: 8 CD audio tracks and computer files (including MP3 files). •...
Page 302 300 UNDERSTANDING YOUR INSTRUMENT PANEL use a 44.1 kHz sampling rate and a 192, 160, 128, 96 or Playback Of MP3 Files VBR bit rates. When a medium containing MP3 data is loaded, the radio checks all files on the medium. If the medium MPEG Specifi- Sampling Fre- Bit Rate (kbps)
Page 303: List Button - Cd Mode For Mp3 Play
UNDERSTANDING YOUR INSTRUMENT PANEL 301 To increase the speed of disc loading, it is recommended Push the INFO button once more to return to elapsed to use CD-R media and single-session discs. To create a time priority mode. single-session disc, enable the “Disc at Once” option Push and hold the INFO button for three seconds or more before writing to the disc.
Page 304: Uconnect (Satellite Radio) - If Equipped
302 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: The AUX device must be turned on and the NOTE: Sirius service is not available in Hawaii and has device’s volume set to the proper level. If the AUX audio limited coverage in Alaska. is not loud enough, turn the device’s volume up.
Page 305 UNDERSTANDING YOUR INSTRUMENT PANEL 303 1. The Electronic Serial Number/Sirius Identification Satellite Antenna Number (ESN/SID). To ensure optimum reception, do not place items on the roof around the rooftop antenna location. Metal objects 2. Your Vehicle Identification Number. placed within the line of sight of the antenna will cause To access the ESN/SID, refer to the following steps: decreased performance.
Page 306 304 UNDERSTANDING YOUR INSTRUMENT PANEL • Driving under wide bridges or along tall buildings can SCAN Button cause intermittent reception. Pushing the SCAN button causes the tuner to search for • Placing objects over or too close to the antenna can the next channel, pausing for eight seconds before con- tinuing to the next.
Page 307 UNDERSTANDING YOUR INSTRUMENT PANEL 305 TUNE Control (Rotary) SETUP Button Turn the rotary TUNE/SCROLL control knob clockwise Pushing the SETUP button allows you to select the to increase or counterclockwise to decrease the channel. following items: • Display Sirius ID number — Push the AUDIO/ MUSIC TYPE Button SELECT button to display the Sirius ID number.
Page 308: Ipod/Usb/Mp3 Control - If Equipped
306 UNDERSTANDING YOUR INSTRUMENT PANEL You may add a second channel to each pushbutton by iPod/USB/MP3 CONTROL — IF EQUIPPED repeating the above procedure with this exception: Push This feature allows an iPod or external USB device to be the SET button twice and SET 2 will show in the display plugged into the USB port, located in the center console window.
Page 309: Connecting The Ipod Or External Usb Device
UNDERSTANDING YOUR INSTRUMENT PANEL 307 Connecting The iPod Or External USB Device Once the audio device is connected and synchronized to the vehicle’s iPod/USB/MP3 control system (iPod or Use the connection cable to connect an iPod or external external USB device may take a few minutes to connect), USB device to the vehicle’s USB/AUX connector port the audio device starts charging and is ready for use by which is located in the center console or glove compart-...
Page 310: Controlling The Ipod Or External Usb Device Using Radio Buttons
308 UNDERSTANDING YOUR INSTRUMENT PANEL • The audio device can be controlled using the radio mode. In Play mode, the following buttons on the radio buttons to Play, Browse, and List the iPod contents. faceplate may be used to control the iPod or external USB device and display data: •...
Page 311 UNDERSTANDING YOUR INSTRUMENT PANEL 309 • A single push backward << RW or forward FF >> will • Push the SCAN button to use iPod/USB/MP3 device jump backward or forward respectively, for five sec- scan mode, which will play the first ten seconds of onds.
Page 312 310 UNDERSTANDING YOUR INSTRUMENT PANEL List Or Browse Mode During all List modes, the iPod displays all lists in “wrap-around” mode. So if the track is at the bottom of During Play mode, pushing any of the buttons described the list, just turn the wheel backward (counterclockwise) below, will bring up List mode.
Page 313 UNDERSTANDING YOUR INSTRUMENT PANEL 311 To exit List mode without selecting a track, push the CAUTION! same PRESET button again to go back to Play mode. • Leaving the iPod or external USB device (or any LIST button: The LIST button will display the top level supported device) anywhere in the vehicle in ex- menu of the iPod or external USB device.
Page 314: Bluetooth Streaming Audio (Btsa)
312 UNDERSTANDING YOUR INSTRUMENT PANEL Bluetooth Streaming Audio (BTSA) Selecting A Different Audio Device Music can be streamed from your cellular phone to the 1. Push the Phone button to begin. Uconnect phone system. 2. After the Ready prompt and following the beep, say Refer to the Uconnect Radio Supplement for further Setup , then say Select Audio Devices.
Page 315: Steering Wheel Audio Controls
UNDERSTANDING YOUR INSTRUMENT PANEL 313 Browse Browsing is not available on a Bluetooth Streaming Audio (BTSA) device. Only the current song that is playing will display info. STEERING WHEEL AUDIO CONTROLS The remote sound system controls are located on the rear surface of the steering wheel.
Page 316: Radio Operation
314 UNDERSTANDING YOUR INSTRUMENT PANEL Pushing the center button will make the radio switch CD Player between the various modes available (AM/FM/SAT/ Pushing the top of the switch once will go to the next CD/HDD/AUX etc.). track on the CD. Pushing the bottom of the switch once will go to the beginning of the current track, or to the The left-hand control is a rocker-type switch with a beginning of the previous track if it is within eight...
Page 317: Cd/Dvd Disc Maintenance
UNDERSTANDING YOUR INSTRUMENT PANEL 315 CD/DVD DISC MAINTENANCE NOTE: If you experience difficulty in playing a particular disc, it may be damaged (e.g., scratched, reflective coat- To keep a CD/DVD in good condition, take the following ing removed, a hair, moisture or dew on the disc) precautions: oversized, or have protection encoding.
Page 318: Climate Controls
316 UNDERSTANDING YOUR INSTRUMENT PANEL CLIMATE CONTROLS The Manual Temperature Controls consist of a series of outer rotary dials and inner push knobs. The air conditioning and heating system is designed to make you comfortable in all types of weather. Blower Control Manual Heating And Air Conditioning Rotate this control to regulate the...
Page 319 UNDERSTANDING YOUR INSTRUMENT PANEL 317 Temperature Control Air Conditioning Control Push this button to engage the Air Rotate this control to regulate the tem- Conditioning. A light will illuminate perature of the air inside the passenger when the Air Conditioning system is compartment.
Page 320 318 UNDERSTANDING YOUR INSTRUMENT PANEL • ECONOMY MODE • Panel If economy mode is desired, push the A/C button to turn Air is directed through the outlets in the instru- OFF the indicator light and the A/C compressor. Then, ment panel. These outlets can be adjusted to direct select Panel, Bi-Level or Floor mode and move the airflow.
Page 321 UNDERSTANDING YOUR INSTRUMENT PANEL 319 • Floor NOTE: • The air conditioning compressor operates in Mix, Air is directed through the floor outlets with a Defrost, or a blend of these modes, even if the Air small amount flowing through the defrost and Conditioning (A/C) button is not pushed.
Page 322: Automatic Temperature Control (Atc) - If Equipped
320 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Automatic Temperature Control (ATC) — If Equipped • Continuous use of the Recirculation mode may make the inside air stuffy and window fogging may occur. The Automatic Temperature Control system automati- Extended use of this mode is not recommended. cally maintains the climate in the cabin of the vehicle at the comfort levels desired by the driver and passenger.
Page 323 UNDERSTANDING YOUR INSTRUMENT PANEL 321 Automatic Operation You will experience the greatest efficiency by simply allowing the system to function automatically. Selecting Operation of the system is quite simple. the “O” (OFF) position on the blower control stops the 1. Turn the Mode Control knob (right knob) and the system completely and closes the outside air intake.
Page 324 322 UNDERSTANDING YOUR INSTRUMENT PANEL insects. Clean with a gentle water spray from behind Manual Operation Override the radiator and through the condenser. Fabric front This system offers a full complement of manual override fascia protectors may reduce airflow to the condenser, features, which consist of Blower Preferred Automatic, reducing air conditioning performance.
Page 325 UNDERSTANDING YOUR INSTRUMENT PANEL 323 I n f o r ma t i o n P r o v i d e d b y :...
Page 326 324 UNDERSTANDING YOUR INSTRUMENT PANEL The operator can override the AUTO mode setting to NOTE: For all settings, except full cold or full hot, there change airflow distribution by rotating the Mode Control is a difference in temperature between the upper and knob (on the right) to one of the following positions.
Page 327 UNDERSTANDING YOUR INSTRUMENT PANEL 325 • Defrost • Recirculation Control Air is directed through the windshield and side The system will automatically control recircu- window demist outlets. Use this mode with maxi- lation. However, pushing the Recirculation mum blower and temperature settings for best wind- Control button will put the system in recircu- shield and side window defrosting.
Page 328: Operating Tips
326 UNDERSTANDING YOUR INSTRUMENT PANEL • Extended use of recirculation may cause the windows system to go into Recirculation Mode, you must first to fog. If the interior of the windows begins to fog, move the Mode knob to Panel, Bi-Level, Mix, or Floor push the Recirculation button to return to outside air.
Page 329 UNDERSTANDING YOUR INSTRUMENT PANEL 327 Standard MS.90032 and 50% water is recommended. Window Fogging Refer to “Maintenance Procedures” in “Maintaining Your Interior fogging on the windshield can be quickly re- Vehicle” for proper coolant selection. moved by turning the mode selector to Defrost. The Defrost/Floor mode can be used to maintain a clear Winter Operation windshield and provide sufficient heating.
Page 330 328 UNDERSTANDING YOUR INSTRUMENT PANEL Side Window Demisters A/C Air Filter — If Equipped A side window demister outlet is located at each end of The A/C Filter prevents most dust and pollen from the instrument panel. These non-adjustable outlets direct entering the cabin.
Page 331 UNDERSTANDING YOUR INSTRUMENT PANEL 329 Control Setting Suggestions For Various Weather Conditions I n f o r ma t i o n P r o v i d e d b y :...
Page 332 I n f o r ma t i o n P r o v i d e d b y :...
Page 333 STARTING AND OPERATING CONTENTS ▫ Five-Speed Manual Transmission...338 STARTING PROCEDURES ....335 ▫ Manual Transmission — If Equipped ..335 ▫...
Page 334 332 STARTING AND OPERATING AUTOSTICK ......355 POWER STEERING .....368 ▫...
Page 335 STARTING AND OPERATING 333 ▫ Electronic Roll Mitigation (ERM) ..386 ▫ Run Flat Tires — If Equipped ... . .406 ▫ Hill Descent Control (HDC) — If Equipped . . .387 ▫...
Page 336 334 STARTING AND OPERATING ▫ Vehicle Certification Label ....431 FUEL REQUIREMENTS ....424 ▫...
Page 337: Starting Procedures
STARTING AND OPERATING 335 STARTING PROCEDURES WARNING! (Continued) Before starting your vehicle, adjust your seat, adjust both • Do not leave the Key Fob in or near the vehicle, or inside and outside mirrors, and fasten your seat belts. in a location accessible to children. A child could operate power windows, other controls, or move WARNING! the vehicle.
Page 338: Automatic Transmission - If Equipped
336 STARTING AND OPERATING Automatic Transmission — If Equipped Normal Starting The shift lever must be in the PARK or NEUTRAL Normal starting of either a cold or a warm engine does position before you can start the engine. Press the brake not require pumping or pressing the accelerator pedal.
Page 339: Extreme Cold Weather
STARTING AND OPERATING 337 in the ON position, release the accelerator pedal and WARNING! (Continued) repeat the “Normal Starting” procedure. another vehicle. This type of start can be dangerous if done improperly, so follow the procedure carefully. WARNING! Refer to “Jump-Starting” in “What To Do In Emer- Never pour fuel or other flammable liquid into the gencies”...
Page 340: Engine Block Heater - If Equipped
338 STARTING AND OPERATING ENGINE BLOCK HEATER — IF EQUIPPED MANUAL TRANSMISSION — IF EQUIPPED The engine block heater warms the engine, and permits Five-Speed Manual Transmission quicker starts in cold weather. Connect the cord to a standard 110-115 Volt AC electrical outlet with a WARNING! grounded, three-wire extension cord.
Page 341 STARTING AND OPERATING 339 CAUTION! • Launching in any gear except 1st gear will result in excessive slipping of the clutch and potentially lugging or stalling the engine. • Use each gear in numerical order, do not skip a gear. Be sure the transmission is in first gear, (not third), when starting from a standing position.
Page 342: Recommended Shift Speeds
340 STARTING AND OPERATING Never shift into REVERSE until the vehicle has come to a Recommended Shift Speeds complete stop. To use your manual transmission for optimal fuel economy, it should be upshifted as listed in the following NOTE: During cold weather, until the transmission lu- table.
Page 343: Downshifting
STARTING AND OPERATING 341 Downshifting When turning a corner or driving up a steep grade, downshift early so that the engine will not be overbur- Proper downshifting will improve fuel economy and dened. prolong engine life. AUTOMATIC TRANSMISSION — IF EQUIPPED CAUTION! CAUTION! If you skip a gear while downshifting or downshift...
Page 344 342 STARTING AND OPERATING NOTE: You must press and hold the brake pedal while WARNING! (Continued) shifting out of PARK. turn the engine OFF, and remove the ignition key. Once the key is removed, the transmission is WARNING! locked in PARK, securing the vehicle against un- •...
Page 345: Key Ignition Park Interlock
STARTING AND OPERATING 343 Key Ignition Park Interlock out of PARK, the ignition switch must be turned to the ON/RUN position (engine running or not) and the brake This vehicle is equipped with a Key Ignition Park Inter- pedal must be pressed. lock which requires the transmission to be in PARK before the ignition switch can be turned to the LOCK/ Six-Speed Automatic Transmission —...
Page 346 344 STARTING AND OPERATING Only shift from DRIVE to PARK or REVERSE when the PARK (P) accelerator pedal is released and the vehicle is stopped. This range supplements the parking brake by locking the Be sure to keep your foot on the brake pedal when transmission.
Page 347 STARTING AND OPERATING 345 WARNING! WARNING! (Continued) • Unintended movement of a vehicle could injure • Never use the PARK position as a substitute for the those in or near the vehicle. As with all vehicles, parking brake. Always apply the parking brake you should never exit a vehicle while the engine is fully when parked to guard against vehicle move- running.
Page 348 346 STARTING AND OPERATING The following indicators should be used to ensure that WARNING! (Continued) you have engaged the transmission into the PARK posi- warned not to touch the parking brake, brake pedal tion: or the gear selector. • When shifting into PARK, firmly move the shift lever •...
Page 349 STARTING AND OPERATING 347 NEUTRAL (N) CAUTION! (Continued) Use this range when the vehicle is standing for prolonged severe transmission damage. Refer to “Recreational periods with the engine running. The engine may be Towing” in “Starting And Operating” and “Towing A started in this range.
Page 350 348 STARTING AND OPERATING control (refer to “AutoStick (Six-Speed Automatic Trans- engine and transmission temperature as well as vehicle mission)” in this section for further information) to select speed. Normal operation will resume once the transmis- a lower gear. Under these conditions, using a lower gear sion temperature has risen to a suitable level.
Page 351 STARTING AND OPERATING 349 In the event of a momentary problem, the transmission If the transmission cannot be reset, authorized dealer can be reset to regain all forward gears by performing the service is required. following steps: Overdrive Operation 1. Stop the vehicle. The automatic transmission includes an electronically controlled Overdrive (sixth gear).
Page 352: Continuously Variable Automatic Transmission (Cvt) - If Equipped
350 STARTING AND OPERATING Torque Converter Clutch Continuously Variable Automatic Transmission (CVT) — If Equipped A feature designed to improve fuel economy has been included in the automatic transmission on your vehicle. The transmission gear position display (located in the A clutch within the torque converter engages automati- instrument cluster) indicates the transmission gear range.
Page 353 STARTING AND OPERATING 351 The transmission shift lever has PARK, REVERSE, NEU- PARK (P) TRAL, and DRIVE shift positions. Some models include a This range supplements the parking brake by locking the LOW position (the LOW position manually downshifts transmission. The engine can be started in this range. the transmission to a lower available ratio based on Never attempt to use PARK while the vehicle is in vehicle speed);...
Page 354 352 STARTING AND OPERATING WARNING! WARNING! (Continued) • Unintended movement of a vehicle could injure • Never use the PARK position as a substitute for the those in or near the vehicle. As with all vehicles, parking brake. Always apply the parking brake you should never exit a vehicle while the engine is fully when parked to guard against vehicle move- running.
Page 355 STARTING AND OPERATING 353 The following indicators should be used to ensure that WARNING! (Continued) you have engaged the transmission into the PARK posi- warned not to touch the parking brake, brake pedal tion: or the gear selector. • When shifting into PARK, firmly move the shift lever •...
Page 356 354 STARTING AND OPERATING NEUTRAL (N) CAUTION! (Continued) Use this range when the vehicle is standing for prolonged severe transmission damage. Refer to “Recreational periods with the engine running. The engine may be Towing” in “Starting And Operating” and “Towing A started in this range.
Page 357: Autostick
STARTING AND OPERATING 355 further information) to select a lower gear ratio. Under LOW (L) — If Equipped these conditions, using a lower gear ratio will improve Use this range for engine braking when descending very performance and extend transmission life by reducing steep grades.
Page 358 356 STARTING AND OPERATING • The transmission will automatically downshift as the Operation vehicle slows (to prevent engine lugging) and will When the shift lever is in the DRIVE position, the display the current gear. transmission will operate automatically, shifting between •...
Page 359: Autostick (Cvt) - If Equipped
STARTING AND OPERATING 357 • The system may revert to automatic shift mode if a maximize engine braking, eliminate undesirable upshifts fault or overheat condition is detected. and downshifts, and improve overall vehicle perfor- mance. This system can also provide you with more To disengage AutoStick mode, hold the shift lever to the control during passing, city driving, cold slippery condi- right (+) until “D”...
Page 360 358 STARTING AND OPERATING • Transmission shifting will be more noticeable when In AutoStick mode, the transmission will shift up or down when (+/-) is manually selected by the driver, AutoStick is engaged. unless an engine lugging or overspeed condition would •...
Page 361: Four-Wheel Drive Operation - If Equipped
STARTING AND OPERATING 359 FOUR-WHEEL DRIVE OPERATION — IF traction surfaces, activate the “4WD LOCK” switch by EQUIPPED pulling up once and releasing. This locks the center coupling allowing more torque to be sent to the rear This feature provides full time, on-demand, four–wheel wheels.
Page 362: Off-Road Driving Tips
360 STARTING AND OPERATING An advantage of the higher ground clearance is a better accelerations, turns or braking. In most cases there are no road signs, posted speed limits or signal lights. Therefore view of the road, allowing you to anticipate problems. you will need to use your own good judgment on what is They are not designed for cornering at the same speeds as safe and what is not.
Page 363: When To Use Low (L Off-Road) With The 4Wd Lock Lever Engaged - If Equipped
STARTING AND OPERATING 361 When To Use Low (L Off-Road) With The 4WD Driving In Snow, Mud And Sand Lock Lever Engaged — If Equipped There is a drastic reduction in traction when driving in When driving off-road, shift into low (L Off-Road [if snow, mud or sand.
Page 364 362 STARTING AND OPERATING will allow the tires to get a fresh bite and help maintain entering any mud hole, get out and determine how deep your momentum. it is, if there are any hidden obstacles and if the vehicle can be safely recovered if stuck.
Page 365: Hill Climbing
STARTING AND OPERATING 363 hard surfaces. Be sure you have a way to reinflate the Before Climbing A Steep Hill tires prior to reducing the pressure. As you approach a hill consider its grade or steepness. Determine if it is too steep. Look to see what the traction CAUTION! is on the hill side trail.
Page 366 364 STARTING AND OPERATING the front end begins to bounce, ease off the throttle Driving Down Hill slightly to bring all four tires back on the ground. As you Before driving down a steep hill you need to determine if approach the crest of the hill, ease off the throttle and it is too steep for a safe descent.
Page 367: Driving Through Water
STARTING AND OPERATING 365 Driving Across An Incline and hill descent braking to control the descent and apply your brakes if necessary, but do not allow the tires to lock. If at all possible avoid driving across an incline. If it is necessary, know your vehicle’s abilities.
Page 368 366 STARTING AND OPERATING be attempted when necessary in a safe responsible man- CAUTION! ner. You should only drive through areas which are designated and approved. You should tread lightly and Water ingestion into the transaxle, transfer case, avoid damage to the environment. You should know engine or vehicle interior can occur if you drive too your vehicles abilities and be able to recover it if some- fast or through too deep of water.
Page 369: After Driving Off-Road
STARTING AND OPERATING 367 soft bottoms, the vehicle will sink in, effectively increas- CAUTION! ing the water level on the vehicle. Be sure to consider this when determining the depth and the ability to safely Muddy waters can reduce the cooling system effec- cross.
Page 370: Power Steering
368 STARTING AND OPERATING • Check threaded fasteners for looseness, particularly on WARNING! (Continued) the chassis, drivetrain components, steering, and sus- not have full braking power when you need it to pension. Retighten them, if required, and torque to the prevent a collision.
Page 371: Power Steering Fluid Check
STARTING AND OPERATING 369 the electric steering system experiences a fault that – SERVICE SYSTEM” message is displayed within the prevents it from providing assist, you will still have the Driver Information Display (DID), this indicates the ability to steer the vehicle manually. vehicle needs to be taken to the dealer for service.
Page 372: Parking Brake
370 STARTING AND OPERATING apparent, and/or the system is not functioning as antici- If necessary, add fluid to restore to the proper indicated pated. Coordinate inspection efforts through an autho- level. With a clean cloth, wipe any spilled fluid from all rized dealer.
Page 373 STARTING AND OPERATING 371 NOTE: • When the parking brake is applied and the automatic transmission is placed in gear, the “Brake Warning Light” will flash. If vehicle speed is detected, a chime will sound to alert the driver. Fully release the parking brake before attempting to move the vehicle.
Page 374 372 STARTING AND OPERATING WARNING! WARNING! (Continued) • Always fully apply the parking brake when leav- • When leaving the vehicle, always remove the Key ing your vehicle or it may roll and cause damage or Fob from the ignition and lock your vehicle. injury.
Page 375: Brake System
STARTING AND OPERATING 373 BRAKE SYSTEM If either of the two hydraulic systems lose normal capa- bility, the remaining system will still function with some Your vehicle is equipped with power assisted brakes as loss of overall braking effectiveness. This will be evident standard equipment.
Page 376: Electronic Brake Control System
374 STARTING AND OPERATING ELECTRONIC BRAKE CONTROL SYSTEM overslip of the rear wheels to avoid vehicle instability, and to prevent the rear axle from entering ABS before the Your vehicle is equipped with an advanced Electronic front axle. Brake Control system (EBC). This system includes Elec- tronic Brake Force Distribution (EBD), Anti-Lock Brake Brake System Warning Light System (ABS), Brake Assist System (BAS), Hill Start...
Page 377 STARTING AND OPERATING 375 • Brake pedal pulsations. braking conditions. The system automatically prevents wheel lock, and enhances vehicle control during braking. • A slight drop of the brake pedal at the end of the stop. The ABS performs a self-check cycle to ensure that the These are all normal characteristics of ABS.
Page 378: Anti-Lock Brake Warning Light
376 STARTING AND OPERATING Anti-Lock Brake Warning Light WARNING! (Continued) The amber “Anti-Lock Brake Warning Light” will turn on • The ABS cannot prevent the natural laws of phys- when the ignition switch is turned to the ON position ics from acting on the vehicle, nor can it increase and may stay on for as long as four seconds.
Page 379: Brake Assist System (Bas)
STARTING AND OPERATING 377 Brake Assist System (BAS) WARNING! The BAS is designed to optimize the vehicle’s braking The Brake Assist System (BAS) cannot prevent the capability during emergency braking maneuvers. The natural laws of physics from acting on the vehicle, system detects an emergency braking situation by sens- nor can it increase the traction afforded by prevailing ing the rate and amount of brake application and then...
Page 380 378 STARTING AND OPERATING does not apply the throttle before this time expires, the is in PARK or NEUTRAL. For vehicles equipped with system will release brake pressure and the vehicle will a manual transmission if the clutch is pressed HSA will roll down the hill as normal.
Page 381 STARTING AND OPERATING 379 Towing With HSA WARNING! (Continued) HSA will also provide assistance to mitigate roll back • Failure to follow these warnings can result in a while towing a trailer. collision or serious personal injury. WARNING! Disabling And Enabling HSA •...
Page 382: Traction Control System (Tcs)
380 STARTING AND OPERATING For vehicles not equipped with the EVIC, perform the 8. Turn the ignition switch to the OFF position and then following steps: back to the ON position. If the sequence was com- pleted properly, the “ESC Off Indicator Light” will 1.
Page 383: Electronic Stability Control (Esc)
STARTING AND OPERATING 381 • Understeer - when the vehicle is turning less than to the wheel that is not spinning. BLD may remain enabled even if TCS and ESC are in a reduced mode. appropriate for the steering wheel position. Electronic Stability Control (ESC) WARNING! This system enhances directional control and stability of...
Page 384 382 STARTING AND OPERATING ESC Operating Modes WARNING! (Continued) The ESC system has three available operating modes for manner, which could jeopardize the user’s safety or four–wheel drive equipped vehicles and two available the safety of others operating modes for two–wheel drive equipped vehicles. •...
Page 385 STARTING AND OPERATING 383 Indicator Light will be illuminated. All other stability WARNING! features of ESC function normally. This mode is intended to be used if the vehicle is in deep snow, sand or gravel When in “Partial Off” mode, the TCS functionality of conditions and more wheel spin than ESC would nor- ESC (except for the limited slip feature described in mally allow is required to gain traction.
Page 386 384 STARTING AND OPERATING Light will illuminate and the “ESC OFF” message will To turn ESC on again, momentarily push the “ESC Off” appear in the odometer. Push and release the Trip Odom- switch. This will restore the “ESC On” mode of operation. eter button located on the instrument cluster to clear this NOTE: The “ESC OFF”...
Page 387 STARTING AND OPERATING 385 ESC Activation/Malfunction Indicator Light And The “ESC Activation/Malfunction Indicator Light” also ESC OFF Indicator Light flashes when TCS is active. If the “ESC Activation/ Malfunction Indicator Light” begins to flash during ac- celeration, ease up on the accelerator and apply as little The “ESC Activation/Malfunction Indicator throttle as possible.
Page 388: Electronic Roll Mitigation (Erm)
386 STARTING AND OPERATING when ESC becomes inactive following the maneuver cannot prevent wheel lift due to other factors, such as that caused the ESC activation. road conditions, leaving the roadway, or striking objects or other vehicles. The “ESC OFF Indicator Light” indicates the NOTE: ERM is disabled anytime the ESC is in “Full Off”...
Page 389: Hill Descent Control (Hdc) - If Equipped
STARTING AND OPERATING 387 Hill Descent Control (HDC) — If Equipped HDC has the capability to sense terrain and will only activate when the vehicle is descending a hill. It will not This system maintains vehicle speed while descending activate on level ground. If desired, HDC can be fully hills during off-road driving situations.
Page 390: Tire Safety Information
388 STARTING AND OPERATING HDC is only intended for low speed off-road driving. At TIRE SAFETY INFORMATION vehicle speeds above 31 mph (50 km/h) HDC will no Tire Markings longer function. If the “HDC Indicator Light” begins to flash this indicates that the brakes are getting too hot and the vehicle should be stopped to allow the brakes to cool.
Page 391 STARTING AND OPERATING 389 • Temporary spare tires are designed for temporary NOTE: emergency use only. Temporary high pressure com- • P (Passenger) — Metric tire sizing is based on U.S. pact spare tires have the letter “T” or “S” molded into design standards.
Page 392 390 STARTING AND OPERATING Tire Sizing Chart EXAMPLE: Example Size Designation: P215/65R15XL 95H, 215/65R15 96H, LT235/85R16C, T145/80D18 103M, 31x10.5 R15 LT P = Passenger car tire size based on U.S. design standards, or ..blank..= Passenger car tire based on European design standards, or LT = Light truck tire based on U.S.
Page 393 STARTING AND OPERATING 391 EXAMPLE: R = Construction code – R means radial construction, or – D means diagonal or bias construction 15, 16, 18 = Rim diameter in inches (in) Service Description: 95 = Load Index – A numerical code associated with the maximum load a tire can carry H = Speed Symbol –...
Page 394: Tire Identification Number (Tin)
392 STARTING AND OPERATING EXAMPLE: Load Identification: Absence of the following load identification symbols on the sidewall of the tire indicates a Standard Load (SL) tire: • XL = Extra load (or reinforced) tire, or • LL = Light load tire or •...
Page 395 STARTING AND OPERATING 393 EXAMPLE: DOT MA L9 ABCD 0301 DOT = Department of Transportation – This symbol certifies that the tire is in compliance with the U.S. Department of Transportation tire safety standards and is approved for highway use MA = Code representing the tire manufacturing location (two digits) L9 = Code representing the tire size (two digits) ABCD = Code used by the tire manufacturer (one to four digits)
Page 396: Tire Terminology And Definitions
394 STARTING AND OPERATING Tire Terminology And Definitions Term Definition B-Pillar The vehicle B-Pillar is the structural member of the body located behind the front door. Cold tire inflation pressure is defined as the tire pressure after Cold Tire Inflation Pressure the vehicle has not been driven for at least three hours, or driven less than 1 mile (1.6 km) after sitting for a minimum of three hours.
Page 397: Tire Loading And Tire Pressure
STARTING AND OPERATING 395 Tire Loading And Tire Pressure Tire And Loading Information Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar or the rear edge of the driver’s side door. Example Tire Placard Location (B-Pillar) Example Tire Placard Location (Door) I n f o r ma t i o n P r o v i d e d b y :...
Page 398 396 STARTING AND OPERATING Tire And Loading Information Placard This placard tells you important information about the: 1. Number of people that can be carried in the vehicle. 2. Total weight your vehicle can carry. 3. Tire size designed for your vehicle. 4.
Page 399 STARTING AND OPERATING 397 NOTE: Under a maximum loaded vehicle condition, Steps For Determining Correct Load Limit gross axle weight ratings (GAWRs) for the front and rear 1. Locate the statement “The combined weight of occu- axles must not be exceeded. For further information on pants and cargo should never exceed XXX lbs or GAWRs, vehicle loading, and trailer towing, refer to XXX kg”...
Page 400 398 STARTING AND OPERATING 4. The resulting figure equals the available amount of NOTE: cargo and luggage load capacity. For example, if • If your vehicle will be towing a trailer, load from your “XXX” amount equals 1,400 lbs (635 kg) and there will trailer will be transferred to your vehicle.
Page 401 STARTING AND OPERATING 399 I n f o r ma t i o n P r o v i d e d b y :...
Page 402: Tires - General Information
400 STARTING AND OPERATING Safety WARNING! WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and • Improperly inflated tires are dangerous and can increase your stopping distance. Use tires of the cause collisions. recommended load capacity for your vehicle.
Page 403: Tire Inflation Pressures
STARTING AND OPERATING 401 Fuel Economy WARNING! (Continued) Underinflated tires will increase tire rolling resistance • Unequal tire pressures from one side of the vehicle resulting in higher fuel consumption. to the other can cause the vehicle to drift to the right or left.
Page 404 402 STARTING AND OPERATING At least once a month: 1 mile (1.6 km) after sitting for a minimum of three hours. The cold tire inflation pressure must not exceed the • Check and adjust tire pressure with a good quality maximum inflation pressure molded into the tire side- pocket-type pressure gauge.
Page 405: Tire Pressures For High Speed Operation
STARTING AND OPERATING 403 Tire pressure may increase from 2 to 6 psi (13 to 40 kPa) WARNING! during operation. DO NOT reduce this normal pressure build up or your tire pressure will be too low. High speed driving with your vehicle under maxi- mum load is dangerous.
Page 406: Tire Types
404 STARTING AND OPERATING Tire Repair Tire Types If your tire becomes damaged, it may be repaired if it All Season Tires — If Equipped meets the following criteria: All Season tires provide traction for all seasons (Spring, • The tire has not been driven on when flat. Summer, Fall and Winter).
Page 407 STARTING AND OPERATING 405 Summer tires do not contain the all season designation or Snow Tires mountain/snowflake symbol on the tire sidewall. Use Some areas of the country require the use of snow tires Summer tires only in sets of four; failure to do so may during the Winter.
Page 408: Run Flat Tires - If Equipped
406 STARTING AND OPERATING While studded tires improve performance on ice, skid See the tire pressure monitoring section for more infor- and traction capability on wet or dry surfaces may be mation. poorer than that of non-studded tires. Some states pro- Spare Tires —...
Page 409 STARTING AND OPERATING 407 equipment tire and wheel found on the front or rear axle Since this tire has limited tread life, the original equip- of your vehicle. This spare tire may be used in the tire ment tire should be repaired (or replaced) and reinstalled rotation for your vehicle.
Page 410 408 STARTING AND OPERATING Full Size Spare — If Equipped your original equipment tire, replace (or repair) the original equipment tire and reinstall on the vehicle at the The full size spare is for temporary emergency use only. first opportunity. This tire may look like the originally equipped tire on the front or rear axle of your vehicle, but it is not.
Page 411: Tire Spinning
STARTING AND OPERATING 409 Tire Spinning Tread Wear Indicators When stuck in mud, sand, snow, or ice conditions, do not Tread wear indicators are in the original equipment tires spin your vehicle’s wheels above 30 mph (48 km/h) or to help you in determining when your tires should be for longer than 30 seconds continuously without stop- replaced.
Page 412: Life Of Tire
410 STARTING AND OPERATING • Distance driven. These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth • Performance tires, tires with a speed rating of V or becomes a 1/16 of an inch (1.6 mm). When the tread is higher, and Summer tires typically have a reduced worn to the tread wear indicators, the tire should be tread life.
Page 413: Replacement Tires
STARTING AND OPERATING 411 Replacement Tires affect your vehicle’s handling. If you ever replace a wheel, make sure that the wheel’s specifications match The tires on your new vehicle provide a balance of many those of the original wheels. characteristics. They should be inspected regularly for wear and correct cold tire inflation pressures.
Page 414: Tire Chains (Traction Devices)
412 STARTING AND OPERATING WARNING! (Continued) CAUTION! braking of your vehicle. This can cause unpredict- Replacing original tires with tires of a different size able handling and stress to steering and suspen- may result in false speedometer and odometer read- sion components.
Page 415: Tire Rotation Recommendations
STARTING AND OPERATING 413 TIRE ROTATION RECOMMENDATIONS The suggested rotation method is the “rearward cross” shown in the following diagram. This rotation pattern The tires on the front and rear of your vehicle operate at does not apply to some directional tires that must not be different loads and perform different steering, driving, reversed.
Page 416: Tire Pressure Monitoring System (Tpms)
414 STARTING AND OPERATING TIRE PRESSURE MONITORING SYSTEM (TPMS) also increase as the vehicle is driven - this is normal and there should be no adjustment for this increased pres- The Tire Pressure Monitor System (TPMS) will warn the sure. driver of a low tire pressure based on the vehicle recom- mended cold placard pressure.
Page 417 STARTING AND OPERATING 415 NOTE: When filling warm tires, the tire pressure may Monitoring Telltale Light will turn OFF only after the need to be increased up to an additional 4 psi (30 kPa) tires are inflated to the vehicle’s recommended cold above the recommended cold placard pressure in order placard pressure value.
Page 418 416 STARTING AND OPERATING • The TPMS should not be used as a tire pressure gauge CAUTION! (Continued) while adjusting your tire pressure. • Using aftermarket tire sealants may cause the Tire • Driving on a significantly under-inflated tire causes Pressure Monitoring System (TPMS) sensor to be- the tire to overheat and can lead to tire failure.
Page 419: Base System
STARTING AND OPERATING 417 Base System Tire Pressure Monitoring Low Pressure Warnings The Tire Pressure Monitoring Telltale Light will illumi- nate in the instrument cluster, a LOW TIRE message will This is the TPMS warning indicator located in the be displayed for a minimum of five seconds, and an instrument cluster.
Page 420 418 STARTING AND OPERATING Check TPMS Warnings 5. Using wheels/tires not equipped with TPM sensors. The Tire Pressure Monitoring Telltale Light will flash on NOTE: Your vehicle is equipped with a compact spare and off for 75 seconds and remain on solid when a system wheel and tire assembly.
Page 421: Premium System - If Equipped
STARTING AND OPERATING 419 4. For each subsequent ignition key cycle, a chime will Premium System — If Equipped sound and the Tire Pressure Monitoring Telltale Light The TPMS uses wireless technology with wheel rim will flash on and off for 75 seconds and then remain on mounted electronic sensors to monitor tire pressure lev- solid.
Page 422 420 STARTING AND OPERATING • Various Tire Pressure Monitoring System Messages, which display in the Electronic Vehicle Information Center (EVIC) • Tire Pressure Monitoring Telltale Light Tire Pressure Monitoring Low Pressure Warnings The Tire Pressure Monitoring Telltale Light will illumi- nate in the instrument cluster and an audible chime will be activated when one or more of the four active road tire pressures are low.
Page 423 STARTING AND OPERATING 421 the graphic display of the pressure value(s) will stop in place of the pressure value(s) indicating which Tire flashing, and the Tire Pressure Monitoring Light will Pressure Monitoring Sensor(s) is not being received. extinguish once the updated tire pressure(s) have been received.
Page 424 422 STARTING AND OPERATING text message will not be present, and a pressure value pressure values still shown. This indicates that the pres- will be displayed instead of dashes. A system fault can sure values are still being received from the TPM sensors occur with any of the following scenarios: but they may not be located in the correct vehicle position.
Page 425: General Information
STARTING AND OPERATING 423 3. However, after driving the vehicle for up to 20 min- long as no tire pressure is below the low-pressure utes above 15 mph (24 km/h), the Tire Pressure warning limit in any of the four active road tires. The Monitoring Telltale Light will flash on and off for 75 vehicle may need to be driven for up to 10 minutes seconds and then remain on solid.
Page 426: 2.0L And 2.4L Engine
424 STARTING AND OPERATING FUEL REQUIREMENTS than 87 can cause engine failure and may void or not be covered by the New Vehicle Limited Warranty. 2.0L And 2.4L Engine Poor quality gasoline can cause problems such as hard starting, stalling, and hesitations. If you experience these These engines are designed to meet all symptoms, try another brand of gasoline before consid- emissions regulations and provide opti-...
Page 427: Gasoline/Oxygenate Blends
STARTING AND OPERATING 425 Gasoline/Oxygenate Blends are not the responsibility of the manufacturer and may void or not be covered under New Vehicle Limited Some fuel suppliers blend unleaded gasoline with oxy- Warranty. genates such as ethanol. E-85 Usage In Non-Flex Fuel Vehicles CAUTION! Non-Flex Fuel Vehicles (FFV) are compatible with gaso- line containing up to 15% ethanol (E-15).
Page 428: Mmt In Gasoline
426 STARTING AND OPERATING MMT In Gasoline Materials Added To Fuel Methylcyclopentadienyl Manganese Tricarbonyl (MMT) Besides using unleaded gasoline with the proper octane is a manganese-containing metallic additive that is rating, gasolines that contain detergents, corrosion and blended into some gasoline to increase octane. Gasoline stability additives are recommended.
Page 429: Fuel System Cautions
STARTING AND OPERATING 427 Fuel System Cautions CAUTION! (Continued) • The use of fuel additives, which are now being CAUTION! sold as octane enhancers, is not recommended. Follow these guidelines to maintain your vehicle’s Most of these products contain high concentrations performance: of methanol.
Page 430: Carbon Monoxide Warnings
428 STARTING AND OPERATING Carbon Monoxide Warnings WARNING! (Continued) • Guard against carbon monoxide with proper main- WARNING! tenance. Have the exhaust system inspected every Carbon monoxide (CO) in exhaust gases is deadly. time the vehicle is raised. Have any abnormal Follow the precautions below to prevent carbon conditions repaired promptly.
Page 431 STARTING AND OPERATING 429 After removing the gas cap, place the gas cap tether cable CAUTION! over a hook on the inside of the fuel door. This keeps the • Damage to the fuel system or emission control gas cap suspended away from and protects the vehicle’s surface.
Page 432: Loose Fuel Filler Cap Message
430 STARTING AND OPERATING • If the gas cap is not tightened properly, the MIL will WARNING! come on. Be sure the gas cap is tightened every time • Never have any smoking materials lit in or near the the vehicle is refueled. vehicle when the gas cap is removed or the tank is Loose Fuel Filler Cap Message being filled.
Page 433: Vehicle Loading
STARTING AND OPERATING 431 VEHICLE LOADING The bar code allows a computer scanner to read the Vehicle Identification Number (VIN). As required by National Highway Traffic Safety Admin- istration regulations, your vehicle has a certification label Gross Vehicle Weight Rating (GVWR) affixed to the driver’s side door or B-Pillar.
Page 434 432 STARTING AND OPERATING Inflation Pressure The best way to figure out the total weight of your vehicle is to weigh it when it is fully loaded and ready for This is the cold tire inflation pressure for your vehicle for operation.
Page 435: Trailer Towing
STARTING AND OPERATING 433 Common Towing Definitions CAUTION! The following trailer towing related definitions will assist Do not load your vehicle any heavier than the you in understanding the following information: GVWR. If you do, parts on your vehicle can break, or Gross Vehicle Weight Rating (GVWR) it can change the way your vehicle handles.
Page 436 434 STARTING AND OPERATING The recommended way to measure GTW is to put your WARNING! fully loaded trailer on a vehicle scale. The entire weight of the trailer must be supported by the scale. It is important that you do not exceed the maximum front or rear GAWR.
Page 437 STARTING AND OPERATING 435 Trailer Sway Control tow vehicle’s front axle and the trailer axle(s). When used in accordance with the manufacturer’s directions, it pro- The trailer sway control is a telescoping link that can be vides for a more level ride, offering more consistent installed between the hitch receiver and the trailer tongue steering and brake control thereby enhancing towing that typically provides adjustable friction associated with...
Page 438: Trailer Hitch Classification
436 STARTING AND OPERATING Trailer Hitch Classification WARNING! (Continued) The following chart provides the industry standard for • Weight Distributing Systems may not be compat- the maximum trailer weight a given trailer hitch class can ible with Surge Brake Couplers. Consult with your tow and should be used to assist you in selecting the hitch and trailer manufacturer or a reputable Rec- correct trailer hitch for your intended towing condition.
Page 439: Trailer Towing Weights (Maximum Trailer Weight Ratings)
STARTING AND OPERATING 437 Trailer Towing Weights (Maximum Trailer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. Maximum GTW (Gross Maximum Tongue Wt. Engine/Transmission Frontal Area Trailer Wt.) (See Note) 2.0L Auto/Man 22 sq ft (2.04 sq m) 1,000 lbs (450 kg) 150 lbs (68 kg)
Page 440: Trailer And Tongue Weight
438 STARTING AND OPERATING NOTE: The trailer tongue weight must be considered as part of the combined weight of occupants and cargo, and should never exceed the weight referenced on the Tire and Loading Information placard. Refer to “Tire Safety Information”...
Page 441: Towing Requirements
STARTING AND OPERATING 439 NOTE: Remember that everything put into or on the CAUTION! trailer adds to the load on your vehicle. Also, additional • Do not tow a trailer at all during the first 500 miles factory-installed options or dealer-installed options must be considered as part of the total load on your vehicle.
Page 442 440 STARTING AND OPERATING WARNING! WARNING! (Continued) • Safety chains must always be used between your Improper towing can lead to a collision. Follow these vehicle and trailer. Always connect the chains to guidelines to make your trailer towing as safe as the frame or hook retainers of the vehicle hitch.
Page 443 STARTING AND OPERATING 441 • Proper tire inflation pressures are essential to the safe WARNING! (Continued) and satisfactory operation of your vehicle. Refer to • Total weight must be distributed between the tow “Tires – General Information” in “Starting And Oper- vehicle and the trailer such that the following four ating”...
Page 444 442 STARTING AND OPERATING Towing Requirements — Trailer Brakes WARNING! • Do not interconnect the hydraulic brake system or • Do not connect trailer brakes to your vehicle’s vacuum system of your vehicle with that of the trailer. hydraulic brake lines. It can overload your brake This could cause inadequate braking and possible system and cause it to fail.
Page 445 STARTING AND OPERATING 443 The Trailer Tow Package may include a four- and seven- CAUTION! pin wiring harness. Use a factory approved trailer har- ness and connector. If the trailer weighs more than 1,000 lbs (454 kg) loaded, it should have its own brakes and they NOTE: Do not cut or splice wiring into the vehicles should be of adequate capacity.
Page 446 444 STARTING AND OPERATING Four-Pin Connector Seven-Pin Connector 1 — Female Pins 4 — Park 1 — Battery 5 — Ground 2 — Male Pin 5 — Left Stop/Turn 2 — Backup Lamps 6 — Left Stop/Turn 3 — Ground 6 —...
Page 447: Towing Tips
STARTING AND OPERATING 445 Towing Tips NOTE: • Using a lower gear ratio while operating the vehicle Before setting out on a trip, practice turning, stopping, and backing up the trailer in an area located away from under heavy loading conditions, will improve perfor- heavy traffic.
Page 448 446 STARTING AND OPERATING • Use speed control in flat terrain and with light loads to AutoStick — If Equipped maximize fuel efficiency. When using the AutoStick shift control, select the highest gear that allows for adequate performance and avoids Cooling System frequent downshifts.
Page 449: Recreational Towing (Behind Motorhome, Etc.)
STARTING AND OPERATING 447 RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) Towing This Vehicle Behind Another Vehicle Towing Condition Wheels OFF the Ground Manual Transmission Automatic Transmission • Transmission in NEU- Flat Tow None NOT ALLOWED TRAL • Key in ACC Position Dolly Tow Front FWD Models ONLY...
Page 450 448 STARTING AND OPERATING NOTE: CAUTION! • When recreationally towing your vehicle, always fol- • DO NOT flat tow any vehicle equipped with an low applicable state and provincial laws. Contact state automatic transmission. Damage to the drivetrain and provincial Highway Safety offices for additional will result.
Page 451 WHAT TO DO IN EMERGENCIES CONTENTS ▫ Jacking Instructions ....456 HAZARD WARNING FLASHERS ...451 ▫...
Page 452 450 WHAT TO DO IN EMERGENCIES FREEING A STUCK VEHICLE ... . .479 TOWING A DISABLED VEHICLE ...482 ▫ With Ignition Key .....484 SHIFT LEVER OVERRIDE .
Page 453: Hazard Warning Flashers
WHAT TO DO IN EMERGENCIES 451 HAZARD WARNING FLASHERS IF YOUR ENGINE OVERHEATS The Hazard Warning flasher switch is located on the In any of the following situations, you can reduce the instrument panel, below the radio. potential for overheating by taking the appropriate ac- tion.
Page 454: Wheel And Tire Torque Specifications
452 WHAT TO DO IN EMERGENCIES CAUTION! WARNING! (Continued) to cool. Never try to open a cooling system pressure Driving with a hot cooling system could damage cap when the radiator or coolant bottle is hot. your vehicle. If the pointer rises to the H (red) mark, the instrument cluster will sound a chime.
Page 455 WHAT TO DO IN EMERGENCIES 453 **Use only your Authorized Dealer recommended lug Tighten the lug nuts/bolts in a star pattern until each nuts/bolts and clean or remove any dirt or oil before nut/bolt has been tightened twice. tightening. Inspect the wheel mounting surface prior to mounting the tire and remove any corrosion or loose particles.
Page 456: Jacking And Tire Changing
454 WHAT TO DO IN EMERGENCIES WARNING! WARNING! (Continued) under a vehicle that is on a jack. If you need to get To avoid the risk of forcing the vehicle off the jack, under a raised vehicle, take it to a service center do not tighten the lug nuts fully until the vehicle has where it can be raised on a lift.
Page 457: Jack Location
WHAT TO DO IN EMERGENCIES 455 Jack Location Spare Tire Stowage The jack and jack-handle are stowed under the load floor The compact spare tire is stowed under the rear load floor in the cargo area. in the cargo area. Spare Tire Removal Lift up the load floor cover and remove the hold down.
Page 458: Jacking Instructions
456 WHAT TO DO IN EMERGENCIES 2. Turn on the Hazard Warning flasher. Jacking Instructions 3. Set the parking brake. WARNING! 4. Place the shift lever in PARK (automatic transmission) Carefully follow these tire changing warnings to or REVERSE (manual transmission). help prevent personal injury or damage to your 5.
Page 459 WHAT TO DO IN EMERGENCIES 457 WARNING! (Continued) • Do not let anyone sit in the vehicle when it is on a jack. • Do not get under the vehicle when it is on a jack. If you need to get under a raised vehicle, take it to a Jack Warning Label service center where it can be raised on a lift.
Page 460 458 WHAT TO DO IN EMERGENCIES 2. Loosen, but do not remove, the wheel nuts by turning them to the left one turn while the wheel is still on the ground. NOTE: There are front and rear jacking locations on each side of the body.
Page 461 WHAT TO DO IN EMERGENCIES 459 Jacking Locations Front Jacking Location CAUTION! Do not attempt to raise the vehicle by jacking on locations other than those indicated in the Jacking Instructions for this vehicle. I n f o r ma t i o n P r o v i d e d b y :...
Page 462 460 WHAT TO DO IN EMERGENCIES jack head is properly engaged with the lift area closest to the wheel to be changed. WARNING! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it.
Page 463 WHAT TO DO IN EMERGENCIES 461 WARNING! To avoid the risk of forcing the vehicle off the jack, do not tighten the wheel nuts fully until the vehicle has been lowered. Failure to follow this warning may result in serious injury. Mounting Spare Tire CAUTION! Be sure to mount the spare tire with the valve stem...
Page 464 462 WHAT TO DO IN EMERGENCIES correctly, have them checked with a torque wrench by WARNING! your authorized dealer or service station. To avoid possible personal injury, handle the wheel 8. Remove the wheel blocks and lower the jack until it is covers with care to avoid contact with any sharp free.
Page 465: Road Tire Installation
WHAT TO DO IN EMERGENCIES 463 WARNING! A loose tire thrown forward in a collision or hard stop could injure the occupants in the vehicle. Have the deflated (flat) tire repaired or replaced immedi- ately. 10. Check the spare tire pressure as soon as possible. Correct the tire pressure as required.
Page 466 464 WHAT TO DO IN EMERGENCIES 3. Install the five wheel lug nuts with the cone shaped 6. After 25 miles (40 km) check the lug nut torque with a end of the nut toward the wheel. Lightly tighten the torque wrench to ensure that all lug nuts are properly lug nuts.
Page 467: Tire Service Kit - If Equipped
WHAT TO DO IN EMERGENCIES 465 3. Lower the vehicle to the ground by turning the jack This kit will provide a temporary tire seal, allowing you handle counterclockwise. to drive your vehicle up to 100 miles (160 km) with a maximum speed of 55 mph (90 km/h).
Page 468: Tire Service Kit Components And Operation
466 WHAT TO DO IN EMERGENCIES Tire Service Kit Components And Operation Using The Mode Select Knob And Hoses Your Tire Service Kit is equipped with the following symbols to indicate the air or sealant mode. Selecting Air Mode Push in the Mode Select Knob (5) and turn to this position for air pump operation only.
Page 469: Tire Service Kit Usage Precautions
WHAT TO DO IN EMERGENCIES 467 Using The Deflation Button Push the Deflation Button (2) to reduce the air pressure in the tire if it becomes over-inflated. Tire Service Kit Usage Precautions • Replace the Tire Service Kit Sealant Bottle (1) and Sealant Hose (6) prior to the expiration date (printed at the lower right hand corner on the bottle label) to assure optimum operation of the system.
Page 470 468 WHAT TO DO IN EMERGENCIES from the vehicle or tire and wheel components. Once WARNING! the sealant dries, it can easily be peeled off and • Do not attempt to seal a tire on the side of the properly discarded. vehicle closest to traffic.
Page 471: Sealing A Tire With Tire Service Kit
WHAT TO DO IN EMERGENCIES 469 WARNING! (Continued) WARNING! (Continued) • Keep Tire Service Kit away from open flames or • Tire Service Kit Sealant solution contains latex. In heat source. case of an allergic reaction or rash, consult a phy- •...
Page 472 470 WHAT TO DO IN EMERGENCIES on the ground. This will provide the best positioning 4. Remove the cap from the valve stem and then screw of the kit when injecting the sealant into the deflated the fitting at the end of the Sealant Hose (6) onto the tire and running the air pump.
Page 473 WHAT TO DO IN EMERGENCIES 471 NOTE: Sealant may leak out through the puncture in the NOTE: If the Mode Select Knob (5) is on Air Mode and tire. the pump is operating, air will dispense from the Air Pump Hose (7) only, not the Sealant Hose (6). If the sealant (white fluid) does not flow within 0 –...
Page 474 472 WHAT TO DO IN EMERGENCIES If the tire does not inflate to at least 26 psi (1.8 Bar) the hose, and place the Tire Service Kit in the vehicle pressure within 15 minutes: storage location. Quickly proceed to (D) “Drive Ve- hicle.”...
Page 475 WHAT TO DO IN EMERGENCIES 473 distribution of the Tire Service Kit Sealant within the tire. 2. Uncoil the power plug and insert the plug into the Do not exceed 55 mph (90 km/h). vehicle’s 12 Volt power outlet. 3. Uncoil the Air Pump Hose (7) (black in color) and WARNING! screw the fitting at the end of hose (7) onto the valve stem.
Page 476 474 WHAT TO DO IN EMERGENCIES NOTE: If the tire becomes over-inflated, push the Defla- NOTE: When having the tire serviced, advise the autho- tion Button to reduce the tire pressure to the recom- rized dealer or service center that the tire has been sealed mended inflation pressure before continuing.
Page 477: Jump-Starting Procedures
WHAT TO DO IN EMERGENCIES 475 the front of the housing. Push the bottle into the NOTE: When using a portable battery booster pack housing. An audible click will be heard indicating the follow the manufacturer’s operating instructions and bottle is locked into place. precautions.
Page 478: Preparations For Jump-Start
476 WHAT TO DO IN EMERGENCIES Preparations For Jump-Start The battery in your vehicle is located in the front of the engine compartment below the air intake duct. To access the battery remove the air intake duct by turning the two finger screws, located on the radiator support.
Page 479: Jump-Starting Procedure
WHAT TO DO IN EMERGENCIES 477 3. If using another vehicle to jump-start the battery, park WARNING! the vehicle within the jumper cables reach, set the • Take care to avoid the radiator cooling fan when- parking brake and make sure the ignition is OFF. ever the hood is raised.
Page 480 478 WHAT TO DO IN EMERGENCIES 4. Connect the opposite end of the negative (-) jumper CAUTION! cable to a good engine ground (exposed metal part of the discharged vehicle’s engine) away from the battery Failure to follow these procedures could result in and the fuel injection system.
Page 481: Freeing A Stuck Vehicle
WHAT TO DO IN EMERGENCIES 479 6. Once the engine is started, remove the jumper cables If frequent jump-starting is required to start your vehicle in the reverse sequence: you should have the battery and charging system in- spected at your authorized dealer. Disconnecting The Jumper Cables 1.
Page 482 480 WHAT TO DO IN EMERGENCIES and REVERSE (with automatic transmission) or 2nd gear NOTE: Push the ESC Off switch, to place the Electronic and REVERSE (with manual transmission), while gently Stability Control (ESC) system in Partial Off mode, pressing the accelerator. Use the least amount of accel- before rocking the vehicle.
Page 483: Shift Lever Override
WHAT TO DO IN EMERGENCIES 481 3. Using a small screwdriver or similar tool, remove the WARNING! shift lever override access cover (located on the right side of the shift lever housing). Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause damage, or even failure, of the axle and tires.
Page 484: Towing A Disabled Vehicle
482 WHAT TO DO IN EMERGENCIES 4. Turn the ignition switch to the ACC or ON/RUN TOWING A DISABLED VEHICLE position, but do not start the engine. This section describes procedures for towing a disabled vehicle using a commercial towing service. 5.
Page 485 WHAT TO DO IN EMERGENCIES 483 6-Speed Auto- Towing Wheels OFF Manual Trans- 6-Speed Auto- CVT Automatic matic (FWD Condition the Ground mission matic 4WD Transmission Only) Flat Tow NONE If transmission is If transmission is operable: operable: ALLOWED • Transmission •...
Page 486: With Ignition Key
484 WHAT TO DO IN EMERGENCIES With Ignition Key Front Wheel Drive (FWD) models (with 6-speed auto- matic only) may also be towed (under the same limita- Automatic Transmission tions shown above) with the rear wheels elevated. • Front Wheel Drive (FWD) vehicles can be towed with the front wheels elevated, or on a flatbed truck (all four CAUTION! wheels OFF the ground).
Page 487 WHAT TO DO IN EMERGENCIES 485 Manual Transmission CAUTION! (Continued) • Front Wheel Drive (FWD) or Four-Wheel Drive (4WD) or drivetrain damage. Damage from improper tow- vehicles can be flat towed (all four wheels on the ing is not covered under the New Vehicle Limited ground) with the transmission in NEUTRAL.
Page 488 486 WHAT TO DO IN EMERGENCIES Without The Ignition Key Special care must be taken when the vehicle is towed with the ignition in the LOCK/OFF position. The only approved method of towing without the ignition key is with a flatbed truck. Proper towing equipment is neces- sary to prevent damage to the vehicle.
Page 489 MAINTAINING YOUR VEHICLE CONTENTS ▫ Engine Oil Filter ..... .498 ENGINE COMPARTMENT — 2.0L ..489 ▫...
Page 490 488 MAINTAINING YOUR VEHICLE ▫ Automatic Transmission (Six-Speed) — If REPLACEMENT BULBS ....534 Equipped ......516 BULB REPLACEMENT .
Page 491: Engine Compartment - 2.0L
MAINTAINING YOUR VEHICLE 489 ENGINE COMPARTMENT — 2.0L 1 — Washer Fluid Reservoir 6 — Air Cleaner Filter 2 — Power Steering Fluid Reservoir 7 — Coolant Pressure Cap 3 — Engine Oil Fill 8 — Engine Oil Dipstick 4 — Brake Fluid Reservoir 9 —...
Page 492: Engine Compartment - 2.4L
490 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT — 2.4L 1 — Washer Fluid Reservoir 6 — Air Cleaner Filter 2 — Power Steering Fluid Reservoir 7 — Coolant Pressure Cap 3 — Engine Oil Fill 8 — Engine Oil Dipstick 4 — Brake Fluid Reservoir 9 —...
Page 493: Onboard Diagnostic System - Obd Ii
MAINTAINING YOUR VEHICLE 491 ONBOARD DIAGNOSTIC SYSTEM — OBD II CAUTION! Your vehicle is equipped with a sophisticated onboard • Prolonged driving with the MIL on could cause diagnostic system called OBD II. This system monitors further damage to the emission control system. It the performance of the emissions, engine, and automatic could also affect fuel economy and driveability.
Page 494: Emissions Inspection And Maintenance Programs
492 MAINTAINING YOUR VEHICLE persists, the message will appear the next time the Normally, the OBD II system will be ready. The OBD II vehicle is started. This might indicate a damaged cap. If system may not be ready if your vehicle was recently the problem is detected twice in a row, the system will serviced, recently had a dead battery or a battery replace- turn on the MIL.
Page 495: Replacement Parts
MAINTAINING YOUR VEHICLE 493 3. Approximately 15 seconds later, one of two things will system to update. A recheck with the above test routine happen: may then indicate that the system is now ready. • The MIL will flash for about 10 seconds and then Regardless of whether your vehicle’s OBD II system is return to being fully illuminated until you turn OFF ready or not, if the MIL is illuminated during normal...
Page 496: Dealer Service
494 MAINTAINING YOUR VEHICLE DEALER SERVICE MAINTENANCE PROCEDURES Your authorized dealer has the qualified service person- The pages that follow contain the required maintenance nel, special tools, and equipment to perform all service services determined by the engineers who designed your operations in an expert manner.
Page 497: Engine Oil
MAINTAINING YOUR VEHICLE 495 Engine Oil CAUTION! (Continued) Checking Oil Level • Your vehicle has been built with improved fluids that protect the performance and durability of your To assure proper engine lubrication, the engine oil must vehicle and also allow extended maintenance inter- be maintained at the correct level.
Page 498 496 MAINTAINING YOUR VEHICLE at the low end of the indicated range will result in the oil NOTE: Under no circumstances should oil change inter- level at the full end of the indicator range. vals exceed 10,000 miles (16,000 km), twelve months or 350 hours of engine run time, whichever comes first.
Page 499 MAINTAINING YOUR VEHICLE 497 American Petroleum Institute (API) Engine Oil Engine Oil Viscosity (SAE Grade) — 2.0L, 2.4L Identification Symbol Engine MOPAR SAE 5W-20 engine oil approved to FCA US This symbol means that the oil has Material Standard MS-6395 such as Pennzoil, Shell Helix been certified by the American or equivalent is recommended for all operating tempera- Petroleum Institute (API).
Page 500: Engine Oil Filter
498 MAINTAINING YOUR VEHICLE Synthetic Engine Oils indiscriminately discarded, can present a problem to the environment. Contact your authorized dealer, service You may use synthetic engine oils provided the recom- station or governmental agency for advice on how and mended oil quality requirements are met, and the recom- where used oil and oil filters can be safely discarded in mended maintenance intervals for oil and filter changes your area.
Page 501: Engine Air Cleaner Filter
MAINTAINING YOUR VEHICLE 499 Engine Air Cleaner Filter Engine Air Cleaner Filter Selection Refer to the “Maintenance Schedule” in the “Mainte- The quality of replacement engine air cleaner filters nance Schedules” section for the proper maintenance varies considerably. Only high quality filters should be intervals.
Page 502 500 MAINTAINING YOUR VEHICLE WARNING! (Continued) CAUTION! splashes in eyes or on skin, flush the area imme- • It is essential when replacing the cables on the diately with large amounts of water. Refer to battery that the positive cable is attached to the “Jump-Starting Procedures”...
Page 503: Air Conditioner Maintenance
MAINTAINING YOUR VEHICLE 501 Air Conditioner Maintenance WARNING! (Continued) For best possible performance, your air conditioner • The air conditioning system contains refrigerant should be checked and serviced by an authorized dealer under high pressure. To avoid risk of personal at the start of each warm season.
Page 504 502 MAINTAINING YOUR VEHICLE Protection Agency and is an ozone-saving product. How- The A/C air filter is located in the fresh air inlet behind ever, the manufacturer recommends that air conditioning the glove box. Perform the following procedure to re- service be performed by authorized dealer or other place the filter: service facilities using recovery and recycling equipment.
Page 505: Body Lubrication
MAINTAINING YOUR VEHICLE 503 CAUTION! The A/C air filter is identified with an arrow to indicate airflow direction through the filter. Failure to properly install the filter will result in the need to replace it more often. 7. Rotate the glove compartment door back into position. Body Lubrication Locks and all body pivot points, including such items as seat tracks, door hinge pivot points and rollers, liftgate,...
Page 506: Windshield Wiper Blades
504 MAINTAINING YOUR VEHICLE components to ensure proper function. When performing Avoid using the wiper blades to remove frost or ice from other underhood services, the hood latch, release mecha- the windshield. Keep the blade rubber out of contact with nism and safety catch should be cleaned and lubricated.
Page 507: Exhaust System
MAINTAINING YOUR VEHICLE 505 in cold weather, select a solution or mixture that meets or have an authorized technician inspect the complete ex- exceeds the temperature range of your climate. This haust system and adjacent body areas for broken, dam- rating information can be found on most washer fluid aged, deteriorated, or mispositioned parts.
Page 508 506 MAINTAINING YOUR VEHICLE WARNING! (Continued) CAUTION! (Continued) • A hot exhaust system can start a fire if you park In the event of engine malfunction, particularly over materials that can burn. Such materials might involving engine misfire or other apparent loss of be grass or leaves coming into contact with your performance, have your vehicle serviced promptly.
Page 509: Cooling System
MAINTAINING YOUR VEHICLE 507 In unusual situations involving grossly malfunctioning Cooling System engine operation, a scorching odor may suggest severe and abnormal catalyst overheating. If this occurs, stop WARNING! the vehicle, turn off the engine and allow it to cool. •...
Page 510 508 MAINTAINING YOUR VEHICLE applicable). If the engine coolant (antifreeze) is dirty or If the engine coolant (antifreeze) is dirty or contains rusty in appearance, the system should be drained, visible sediment, have an authorized dealer clean and flushed, and refilled with fresh engine coolant (anti- flush with OAT coolant (antifreeze) (conforming to freeze).
Page 511 MAINTAINING YOUR VEHICLE 509 CAUTION! (Continued) CAUTION! (Continued) • This vehicle has not been designed for use with Organic Additive Technology (OAT) engine cool- propylene glycol-based engine coolant (antifreeze). ant is different and should not be mixed with Use of propylene glycol-based engine coolant (an- Hybrid Organic Additive Technology (HOAT) en- tifreeze) is not recommended.
Page 512 510 MAINTAINING YOUR VEHICLE that meets the requirements of FCA Material Standard Please note that it is the owner’s responsibility to main- MS.90032. When adding engine coolant (antifreeze): tain the proper level of protection against freezing ac- cording to the temperatures occurring in the area where •...
Page 513 MAINTAINING YOUR VEHICLE 511 Cooling System Pressure Cap WARNING! (Continued) The cap must be fully tightened to prevent loss of engine pressure cap while the system is hot or under coolant (antifreeze), and to ensure that engine coolant pressure. (antifreeze) will return to the radiator from the coolant •...
Page 514 512 MAINTAINING YOUR VEHICLE Coolant Level Points To Remember The coolant bottle provides a quick visual method for NOTE: When the vehicle is stopped after a few miles/ determining that the coolant level is adequate. With the kilometers of operation, you may observe vapor coming engine idling and warm to normal operating tempera- from the front of the engine compartment.
Page 515: Brake System
MAINTAINING YOUR VEHICLE 513 • If frequent engine coolant (antifreeze) additions are result in unsatisfactory engine coolant (antifreeze) required, the cooling system should be pressure tested performance, poor gas mileage, and increased emis- for leaks. sions. • Maintain engine coolant (antifreeze) concentration at a Brake System minimum of 50% OAT coolant (conforming to In order to assure brake system performance, all brake...
Page 516 514 MAINTAINING YOUR VEHICLE Brake Master Cylinder NOTE: If your vehicle is equipped with a manual transmission, the brake fluid reservoir supplies fluid to The fluid level in the master cylinder should be checked both the brake system and the clutch release system. The when performing under hood services, or immediately if two systems are separated in the reservoir, and a leak in the brake system warning light is on.
Page 517 MAINTAINING YOUR VEHICLE 515 WARNING! WARNING! (Continued) cause it to boil unexpectedly during hard or pro- • Use only manufacturer’s recommended brake longed braking, resulting in sudden brake failure. fluid. Refer to “Fluids, Lubricants, And Genuine This could result in a collision. Parts”...
Page 518: Automatic Transmission (Six-Speed) - If
516 MAINTAINING YOUR VEHICLE No chemical flushes should be used in any transmission; CAUTION! only the approved lubricant should be used. Use of improper brake fluids will affect overall CAUTION! clutch system performance. Improper brake fluids may damage the clutch system resulting in loss of Using a transmission fluid other than the manufac- clutch function and the ability to shift the transmis- turer’s recommended fluid may cause deterioration...
Page 519 MAINTAINING YOUR VEHICLE 517 leaks. Avoid using transmission sealers as they may checked. Operating the vehicle with an improper fluid adversely affect seals. level can cause severe transmission damage. CAUTION! CAUTION! Do not use chemical flushes in your transmission as If a transmission fluid leak occurs, visit your autho- the chemicals can damage your transmission compo- rized dealer immediately.
Page 520: Automatic Transmission (Cvt) - If Equipped
518 MAINTAINING YOUR VEHICLE fluid becomes contaminated (with water, etc.), or if the CAUTION! transmission is disassembled for any reason. Using a transmission fluid other than the manufac- Automatic Transmission (CVT) — If Equipped turer’s recommended fluid may cause belt slip and Selection Of Lubricant (CVT) result in a complete transmission failure! Refer to “Fluids, Lubricants, And Genuine Parts”...
Page 521 MAINTAINING YOUR VEHICLE 519 CAUTION! CAUTION! Do not use chemical flushes in your transmission as If a transmission fluid leak occurs, visit your autho- the chemicals can damage your transmission compo- rized dealer immediately. Severe transmission dam- nents. Such damage is not covered by the New age may occur.
Page 522: Manual Transmission - If Equipped
520 MAINTAINING YOUR VEHICLE Manual Transmission — If Equipped the vehicle. Fluid changes are not necessary unless lubri- cant has become contaminated with water. Lubricant Selection NOTE: If contaminated with water, the fluid should be Use only the manufacturers recommended transmission changed immediately.
Page 523: Power Transfer Unit (Ptu) - Awd/4Wd Models
MAINTAINING YOUR VEHICLE 521 Add fluid, if necessary, to maintain the proper level. Add fluid, if necessary, to maintain the proper level. Frequency Of Fluid Change Frequency Of Fluid Change Refer to the “Maintenance Schedule” for the proper Refer to the “Maintenance Schedule” for the proper maintenance intervals.
Page 524 522 MAINTAINING YOUR VEHICLE The following maintenance recommendations will enable Washing you to obtain maximum benefit from the corrosion • Wash your vehicle regularly. Always wash your ve- resistance built into your vehicle. hicle in the shade using MOPAR Car Wash, or a mild car wash soap, and rinse the panels completely with What Causes Corrosion? clear water.
Page 525 MAINTAINING YOUR VEHICLE 523 • If you detect any stone chips or scratches in the paint, CAUTION! touch them up immediately. The cost of such repairs is • Do not use abrasive or strong cleaning materials considered the responsibility of the owner. such as steel wool or scouring powder that will •...
Page 526 524 MAINTAINING YOUR VEHICLE Wheel And Wheel Trim Care CAUTION! • All wheels and wheel trim, especially aluminum and Do not use scouring pads, steel wool, a bristle brush, chrome plated wheels, should be cleaned regularly or metal polishes. Do not use oven cleaner. These with a mild soap and water to prevent corrosion.
Page 527 MAINTAINING YOUR VEHICLE 525 • For tough stains, apply MOPAR Total Clean, or a mild Your leather upholstery can be best preserved by regular soap solution to a clean, damp cloth and remove stain. cleaning with a damp soft cloth. Small particles of dirt Use a fresh, damp towel to remove soap residue.
Page 528 526 MAINTAINING YOUR VEHICLE Cleaning Headlights CAUTION! Your vehicle has plastic headlights that are lighter and Direct contact of air fresheners, insect repellents, less susceptible to stone breakage than glass headlights. suntan lotions, or hand sanitizers to the plastic, Plastic is not as scratch resistant as glass and therefore painted, or decorated surfaces of the interior may different lens cleaning procedures must be followed.
Page 529 MAINTAINING YOUR VEHICLE 527 equipped with radio antennas. Do not use scrapers or Instrument Panel Bezels other sharp instrument that may scratch the elements. CAUTION! When cleaning the rear view mirror, spray cleaner on the towel or cloth that you are using. Do not spray cleaner When installing hanging air fresheners in your ve- directly on the mirror.
Page 530: Fuses
528 MAINTAINING YOUR VEHICLE 2. Dry with a soft cloth. WARNING! (Continued) Seat Belt Maintenance disassemble or modify the system. Seat belt assem- blies must be replaced after a collision if they have Do not bleach, dye, or clean the belts with chemical been damaged (i.e., bent retractor, torn webbing, etc.).
Page 531: Integrated Power Module (Ipm)
MAINTAINING YOUR VEHICLE 529 WARNING! (Continued) • Before replacing a fuse, make sure that the ignition is off and that all the other services are switched off and/or disengaged. • If the replaced fuse blows again, contact an autho- rized dealer. •...
Page 532 530 MAINTAINING YOUR VEHICLE Cavity Cartridge Fuse Mini-Fuse Description 20 Amp Blue – Trailer Tow – If Equipped – 15 Amp Lt Blue AWD/4WD Control Module – If Equipped – 10 Amp Red Rear Center Brake Light Switch – 10 Amp Red Ignition Switch/Clock Spring –...
Page 533 MAINTAINING YOUR VEHICLE 531 Cavity Cartridge Fuse Mini-Fuse Description – 15 Amp Lt Blue Power Outlet – 20 Amp Yellow 115V AC Inverter – If Equipped – 20 Amp Yellow Cigar Lighter – 10 Amp Red Instrument Cluster 40 Amp Green –...
Page 534 532 MAINTAINING YOUR VEHICLE Cavity Cartridge Fuse Mini-Fuse Description – 15 Amp Lt Blue Auto Shutdown Relay – 15 Amp Lt Blue Power Sunroof – If Equipped – 10 Amp Red Heated Mirror – If Equipped – 15 Amp Lt Blue Auto Shutdown Relay –...
Page 535 MAINTAINING YOUR VEHICLE 533 Cavity Cartridge Fuse Mini-Fuse Description – 10 Amp Red J1962 Conn/Powertrain Con- trol Module 30 Amp Pink – Antilock BrakeValve 40 Amp Green – Antilock Brake Pump 30 Amp Pink – Headlamp/Washer Control/ Smart Glass – If Equipped –...
Page 536: Vehicle Storage
534 MAINTAINING YOUR VEHICLE VEHICLE STORAGE in the fresh air and high blower setting. This will ensure adequate system lubrication to minimize the If you will not be using your vehicle for more than 21 possibility of compressor damage when the system is days, you may want to take steps to preserve your started again.
Page 537: Bulb Replacement
MAINTAINING YOUR VEHICLE 535 Exterior Bulbs Bulb Number Low Beam/High Beam Headlamp Front Park/Turn Signal/Side Marker Lamp 3757KA Front Fog Lamp PSX24W Center High Mounted Stop Lamp (CHMSL) LED Assembly (Serviced At Authorized Dealer) Rear Tail/Turn/Stop Lamp 3157 Backup Lamp W16W (921) License Lamp BULB REPLACEMENT...
Page 538: Fog Lamps
536 MAINTAINING YOUR VEHICLE 3. Remove the green connector from the back of the bulb CAUTION! by pulling straight back. Do not touch the new bulb with your fingers. Oil 4. Twist the bulb to the left. contamination will severely shorten bulb life. If the 5.
Page 539: License Lamps
MAINTAINING YOUR VEHICLE 537 License Lamps Center High-Mounted Stoplamp This light is an LED assembly. See your authorized dealer 1. Use a screw driver to gently pry against the side of the for replacement. snap tab to remove the lamp from the liftgate. 2.
Page 540: Fluids, Lubricants, And Genuine Parts
538 MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS, AND GENUINE PARTS Engine Component Fluid, Lubricant, or Genuine Part Engine Coolant We recommend you use MOPAR Antifreeze/Coolant 10 Year/150,000 Mile Formula OAT (Organic Additive Technology) or equivalent meeting the requirements of FCA Material Standard MS.90032. Engine Oil We recommend you use API Certified SAE 5W-20 Engine Oil, meeting the requirements of FCA US Material Standard MS-6395 such as MOPAR,...
Page 541 MAINTAINING YOUR VEHICLE 539 CAUTION! CAUTION! (Continued) • Do not use water alone or alcohol-based engine • Mixing of engine coolant (antifreeze) other than coolant (antifreeze) products. Do not use additional specified Organic Additive Technology (OAT) en- rust inhibitors or antirust products, as they may not gine coolant (antifreeze), may result in engine be compatible with the radiator engine coolant and damage and may decrease corrosion protection.
Page 542: Chassis
540 MAINTAINING YOUR VEHICLE Chassis Component Fluid, Lubricant, or Genuine Part Automatic Transmission (CVT) — If Equipped Use only MOPAR CVTF+4 Continuously Variable Transmission Fluid or equivalent. Failure to use the correct fluid may affect the function or performance of your transmission.
Page 543 MAINTAINING YOUR VEHICLE 541 Component Fluid, Lubricant, or Genuine Part Power Transfer Unit (PTU) We recommend you use MOPAR Gear & Axle Lubricant SAE 80W-90 API GL 5. Brake Master Cylinder We recommend you use MOPAR DOT 3, SAE J1703 should be used.
Page 544 I n f o r ma t i o n P r o v i d e d b y :...
Page 545: Maintenance Schedules
MAINTENANCE SCHEDULES CONTENTS ▫ Maintenance Chart.....547 MAINTENANCE SCHEDULE ....544 I n f o r ma t i o n P r o v i d e d b y :...
Page 546 544 MAINTENANCE SCHEDULES MAINTENANCE SCHEDULE On Electronic Vehicle Information Center (EVIC) equipped vehicles, “Oil Change Required” will be dis- Your vehicle is equipped with an automatic oil change played in the EVIC and a single chime will sound, indicator system. The oil change indicator system will indicating that an oil change is necessary.
Page 547 MAINTENANCE SCHEDULES 545 NOTE: Under no circumstances should oil change inter- Once A Month Or Before A Long Trip: vals exceed 10,000 miles (16,000 km), twelve months or • Check engine oil level 350 hours of engine run time, whichever comes first. The •...
Page 548 546 MAINTENANCE SCHEDULES Required Maintenance Intervals. At Every Oil Change Interval As Indicated By Oil Change Indicator System: Refer to the maintenance schedules on the following • Change oil and filter. page for the required maintenance intervals. • Rotate the tires. Rotate at the first sign of irregu- lar wear, even if it occurs before the oil indicator system turns on.
Page 549 MAINTENANCE SCHEDULES 547 Maintenance Chart Refer to the Maintenance Schedules on the following pages for the required maintenance intervals. Mileage or time passed (whichever comes first) Or Years: 2 Or Kilometers: Additional Inspections Inspect the CV joints. Inspect front suspension, boot seals. tie rod ends, and replace if necessary.
Page 550 548 MAINTENANCE SCHEDULES Mileage or time passed (whichever comes first) Or Years: 2 Or Kilometers: Additional Maintenance Replace engine air cleaner filter. Replace air conditioning/cabin air filter. Replace spark plugs** Flush and replace the engine coolant at 10 years or 150,000 miles (240,000 km) whichever comes first.
Page 551 MAINTENANCE SCHEDULES 549 Mileage or time passed (whichever comes first) Or Years: 2 Or Kilometers: Change the automatic transmission fluid and filter. (CVT only) Change the automatic transmission fluid (six-speed only) if you frequently drive: on rough or unpaved roads, on mountain roads, on short trips, in heavy city traffic during hot weather, or if you use the ve- hicle for police, taxi, fleet, or frequent trailer towing.
Page 552 550 MAINTENANCE SCHEDULES Mileage or time passed (whichever comes first) Or Years: 2 Or Kilometers: Change the manual transmission fluid if using your vehicle for any of the following: trailer towing, heavy loading, taxi, police, delivery service (com- mercial service), off-road, desert operation or more than 50% of your driving is at sustained high speeds during hot weather, above 90°F (32°C).
Page 553 MAINTENANCE SCHEDULES 551 WARNING! • You can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic.
Page 554 I n f o r ma t i o n P r o v i d e d b y :...
Page 555 IF YOU NEED CONSUMER ASSISTANCE CONTENTS ▫ Customer Assistance For The Hearing Or Speech SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE ..... . .555 Impaired (TDD/TTY).
Page 556 554 IF YOU NEED CONSUMER ASSISTANCE ▫ Traction Grades ..... . .561 PUBLICATION ORDER FORMS ... .560 ▫...
Page 557: Suggestions For Obtaining Service For Your Vehicle
IF YOU NEED CONSUMER ASSISTANCE 555 SUGGESTIONS FOR OBTAINING SERVICE FOR Be Reasonable With Requests YOUR VEHICLE If you list a number of items and you must have your vehicle by the end of the day, discuss the situation with Prepare For The Appointment the service advisor and list the items in order of priority.
Page 558: Fca Us Llc Customer Center
556 IF YOU NEED CONSUMER ASSISTANCE • Authorized dealer name facilities, factory-trained technicians, special tools, and the latest information to ensure the vehicle is fixed • Vehicle Identification Number (VIN) correctly and in a timely manner. • Vehicle delivery date and mileage This is why you should always talk to an authorized FCA US LLC Customer Center dealer service manager first.
Page 559: In Mexico Contact
IF YOU NEED CONSUMER ASSISTANCE 557 In Mexico Contact Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) Av. Prolongacion Paseo de la Reforma, 1240 To assist customers who have hearing difficulties, the Sante Fe C.P. 05109 manufacturer has installed special TDD (Telecommuni- Mexico, D.
Page 560 558 IF YOU NEED CONSUMER ASSISTANCE Warranty expires. The manufacturer stands behind only We appreciate that you have made a major investment the manufacturer’s service contracts. If you purchased a when you purchased the vehicle. An authorized dealer manufacturer’s service contract, you will receive Plan has also made a major investment in facilities, tools, and Provisions and an Owner Identification Card in the mail training to assure that you are absolutely delighted with...
Page 561: Warranty Information
IF YOU NEED CONSUMER ASSISTANCE 559 WARRANTY INFORMATION If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in See the Warranty Information Booklet, located on the a group of vehicles, it may order a recall and remedy DVD, for the terms and provisions of FCA US LLC campaign.
Page 562: Publication Order Forms
560 IF YOU NEED CONSUMER ASSISTANCE defect to the Canadian government should contact Trans- complete working knowledge of the vehicle, system, port Canada, Motor Vehicle Defect Investigations and and/or components is written in straightforward lan- Recalls at 1-800-333-0510 or go to http://www.tc.gc.ca/ guage with illustrations, diagrams, and charts.
Page 563: Traction Grades
IF YOU NEED CONSUMER ASSISTANCE 561 Call toll free at: Treadwear • 1-800-890-4038 (U.S.) The Treadwear grade is a comparative rating, based on the wear rate of the tire when tested under controlled • 1-800-387-1143 (Canada) conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half times as well on the government course as a tire graded Visit us on the Worldwide Web at:...
Page 564: Temperature Grades
562 IF YOU NEED CONSUMER ASSISTANCE represent higher levels of performance on the laboratory WARNING! test wheel, than the minimum required by law. The traction grade assigned to this tire is based on WARNING! straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or The temperature grade for this tire is established for peak traction characteristics.
Page 565 INDEX I n f o r ma t i o n P r o v i d e d b y :...
Page 566 564 INDEX Adding Engine Coolant (Antifreeze) ... .509 Side Air Bags ......64 Adding Fuel .
Page 567 INDEX 565 Capacities ......537 Autostick......355, 357 Disposal .
Page 568 566 INDEX Bulbs, Light ......101, 534 Cargo Tie-Downs ......206 Car Washes .
Page 569 INDEX 567 Installing Child Restraints Using The Vehicle Seat Compass Variance ......258 Belt ........90 Connector Lower Anchors And Tethers For Children .
Page 570 568 INDEX Cupholders ......202 Remote Keyless Entry (RKE) ....29 Customer Assistance .
Page 571 INDEX 569 Emergency, In Case Of Oil Synthetic ......498 Jacking .......454 Overheating .
Page 572 570 INDEX Fluid Capacities ......537 Clean Air ......424 Fluid Leaks .
Page 573 INDEX 571 Gauges Head Restraints ......156 Fuel ....... . .240 Heated Mirrors .
Page 574 572 INDEX Instrument Cluster ....229, 230, 243 Key, Replacement ......16 Instrument Panel And Controls .
Page 575 INDEX 573 Brake Warning ......226 Map Reading ......169 Bulb Replacement .
Page 576 574 INDEX Lug Nuts .......452 Mirrors ....... .108 Lumbar Support .
Page 577 INDEX 575 Oil Change Indicator, Reset ....251 Operating Precautions ..... .491 Oil, Engine .
Page 578 576 INDEX Sunroof ......191 Radio Frequency Transfer Unit ......521 General Information .
Page 579 INDEX 577 Remote Control Safety Defects, Reporting ....559 Door Locks ......20 Safety, Exhaust Gas.
Page 580 578 INDEX Seat Belts ......41, 99 Seatback Release ......155 Adjustable Shoulder Belt .
Page 581 INDEX 579 Spare Tire .....406, 407, 408, 455 Storage, Vehicle......327 Spark Plugs .
Page 582 580 INDEX Air Pressure ......400 Spare Tire ..... .406, 408, 455 Chains .
Page 583 INDEX 581 Minimum Requirements ....439 UCI Connector ......306 Tips .
Page 584 582 INDEX Understanding Your Instrument Panel...217 Voice Command Uniform Tire Quality Grades ....561 Commands ......145 Universal Consumer Interface (UCI) Connector .
Page 585 INDEX 583 Windshield Defroster ... . .99, 319, 324, 325 Windshield Washers ....170, 172 Windshield Wiper Blades .
Page 586 INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this The antenna cable should be as short as practical and vehicle’s electronic system to provide immunity to radio routed away from the vehicle wiring when possible. Use frequency signals. Mobile two-way radios and telephone only fully shielded coaxial cable.

Jeep 2016 Patriot Owner's Manual

Introduction

Things to Know before Starting Your Vehicle

Understanding the Features of Your Vehicle

Understanding Your Instrument Panel

Starting and Operating

Quick Links

Chapters

Related Manuals for Jeep 2016 Patriot

Summary of Contents for Jeep 2016 Patriot