Download  Print this page

Makita 2106 Instruction Manual

Portable band saw.
Hide thumbs

Advertisement

Portable Band Saw
-~
~
~
Max. cutting capacity
Round
Rectangular workpiece
workpiece
Without optional stand
With optional stand
115
mm
dia.
115
mm x
115
mm
75
mm x
1 1 0
mm
14-112")
14-1/2"
x
4-112")
(3"
x
4-3/8")
MODEL 2106
MODEL 2106K
Wlth Steel Carrylnlpcase
Blade speed
No load surface
(FPM)
High
Low
260
200
INSTRUCTION MANUAL
Blade size
Thickness
Length
Width
1,140
mm
1 3
mm
0.5
mm
144-718"')
1112")
LO207
SPECIFICATIONS
Net
weight
5.5
kg
Overall dimensions
Height
x
Width
x
Length
235
mm x
230
mm x
500
mm
(9-114'
x
9"
x
20')
(12.1
lbs)
~
~~~~~
~~
+
Manufacturer reserves t h e r i g h t t o change specifications without notice
Note: Specifications m a y differ f r o m c o u n t r y t o country.

Advertisement

Table of Contents

   Also See for Makita 2106

   Related Manuals for Makita 2106

   Summary of Contents for Makita 2106

  • Page 1 With optional stand mm x 1 1 0 4-112") (3" 4-3/8") Overall dimensions Thickness Height Width mm x (9-114' LO207 MODEL 2106 MODEL 2106K Wlth Steel Carrylnlpcase Blade speed (FPM) No load surface High weight Length mm x 20') (12.1 9"...
  • Page 2 SAFETY INSTRUCTIONS WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. CONSIDER WORK AREA ENVIRONMENT.
  • Page 3 14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking t o see that keys and adjusting wrenches are removed from AVOID UNINTENTIONAL STARTING. Don‘t carry tool with finger on switch. Be sure switch is OFF when plugging in. EXTENSION CORDS. Make sure your extension cord is in good condition. When using an extension cord, be sure t o use one heavy enough t o carry the current your product will draw.
  • Page 4 Cutting workpieces covered with unexpectedly. Wipe off all excess oil from workpieces before cutting. Never use cutting oil as a cutting lubricant. Use only Makita cutting wax. 6. Do not wear gloves during operation.
  • Page 5 Switch action To start the tool, simply pull the trigger. Release the trigger to stop. For continuous operation, pull the trigger and then push in the lock button. To stop the tool from the locked position, pull the trigger fully, then release it.
  • Page 6 Installing or removing blade CAUTION Always be sure that the tool is switched off and unplugged before installing or removing the blade. Oil on the blade can cause the blade to slip or come off unexpectedly. Wipe off all ex- oil with a cloth before installing the blade.
  • Page 7 CAUTION : When turning the blade tightening lever clockwise to blade may come off unexpectedly. Be careful. Installing stopper plate (For Model 2106 This tool i s shipped from the factory without the stopper plate installed. Install the stopper plate follows.
  • Page 8 If not square, loosen the bolts securing the stopper plate and adjust the stopper plate accordingly. Cutting lubricant When cutting metals, use Makita cutting cutting lubricant. To apply the as a cutting wax to the blade teeth, start the tool and cut in to the cutting wax in the figure.
  • Page 9 Hold the tool shown in the figure with the stopper plate contacting the workpiece and the blade clear of the workpiece. Turn the tool on and wait until the blade attains full speed. Gently lower the blade into the cut. The weight of the tool or slightly pressing the tool down will supply adequate pressure for the cutting.
  • Page 10 Ask Makita Authorized or Factory Service Centers to replace them. MA1 NTENANCE CAUTION : Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance.
  • Page 11 To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized always using Makita replacement parts. Brush holder cap Factory Service Centers,...
  • Page 12 7 9 2 5 5 7 - A 7 9 2 5 5 6 - A 792555-A wrench Part No. 783209-6 Makita tool specified in this risk injury to persons. The Workpiece t o steel M i l d steel,...
  • Page 13 Cutting wax Part 191897-9 Steel carrying case Part No. 823204-5 Portable band saw stand Part 122370-8 ( F o r accurate square cutting operations)
  • Page 14 Feb.-04-'88 PORTABLE BAND SAW Model 2106 Note: The switch, noise suppressor and other part configurations may differ from country to country.
  • Page 15 MODEL 2106 ' E M DESCRIPTION MACHINE M6x4O IWith Washer1 Hex Socket Head Bolt Flat Washer 6 Grip 80 Hex Socket Head Bolt M5x22 Frame Cover Hex Socket Head Bolt M5x10 Laver Flat Washer 20 Upper Holder Ball Bearing 69622...
  • Page 16 MAKCTA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted t o be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase.

This manual is also suitable for:

2106k

Comments to this Manuals

Symbols: 0
Latest comments: