VTech ErisStation VCS754 Quick Start Manual

ErisStation
TM
Wireless Conference System
SIP Conference Phone with Wireless Mics
Quick Start Guide
businessphones.vtech.com
Model: VCS754
Introduction
• The ErisStation SIP Conference Phone with Wireless Mics
requires connection to AC power to operate.
• The supplied power adapter is designed for use with only the
ErisStation SIP Conference Phone with Wireless Mics. It is
not PoE compatible and is not designed to power any network
devices. Do not connect the supplied power adapter to any other
network devices through the supplied DC power cable or any
other Cat5e ethernet cable.
• Connect the base unit only with the supplied DC power cable with
yellow plugs. This cable has a shielded interface and ferrite added
for optimal performance.
• The ErisStation SIP Conference Phone with Wireless Mics
requires a network connection to an IP PBX to operate. This
quick start guide assumes that your network infrastructure
is established and that your IP PBX phone service has been
ordered and configured for your location. For more information
about installation options and phone setup, see the VCS754
User's manual and the VCS754 Administrator and Provisioning
Manual, available at businessphones.vtech.com
• When the base unit is powered up, the status indicators turn
green for about two seconds.
• The AC power cord is intended for a vertical or floor mount
position. The prongs are not designed to hold the plug in place if it
is plugged into a ceiling or cabinet outlet.
Introduction
This quick start guide provides you with the basic installation,
setup, and operation instructions. A limited set of features are
described in abbreviated form.
You may refer to the user's manual for complete installation
and operation instructions for this innovative and feature-rich
VTech product.
ErisStation TM and Orbitlink Wireless Technology
Communications, Inc.
Install the wireless mic battery
1. Place the battery (with the label THIS SIDE UP facing up)
into the battery compartment.
2. Slide the battery door until it clicks into place.
.
3. Place the wireless mics into the charging cradles until they
are flush.
The status indicator on the wireless mic turns orange when charging,
and turns off when the wireless mic is fully charged.
VoIPon www.voipon.co.uk sales@voipon.co.uk Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299
Parts checklist
Your VCS754 SIP Conference Phone with Wireless Mics package
contains the following items. Save your sales receipt and original
packaging in the event warranty service is necessary.
SIP Conference Phone with Wireless Mics
User's manual
b u s i n e s s p h o n e s .v t e c h . c o m
SIP Conference Phone with Wireless Mics
Quick Start Guide
b u s i n e s s p h o n e s .v t e c h . c o m
Model: VCS754
Model: VCS754
User's manual Quick start guide
Battery ×4
Li-ion Polymer batteries.
(x4)
(x4)
(x4) (x4)
Quick start guide
Phone line cord connector cable
AC power cord DC power cable
(with yellow plugs)
To purchase any accessories or replacements, visit our website at
TM are trademarks of VTech
businessphones.vtech.com or call 1-888-370-2006.
Status indicators overview
Status indicators on the base unit
Power up • Green for about two seconds.
On a call • Green during a call.
• Red when the system is muted during a call.
Incoming call • Flashes green when there is an incoming call.
Connect base unit
Connect the base unit as shown below.
4
Wireless mic ×4
Base unit
1. Plug one end of the DC power cable into the power jack of
the base unit, and plug the other end into the VCS754 jack
of the power adapter. Route the cord through the slots.
2. Plug one end of the Ethernet cable into the LAN jack of the
Battery door ×4 Power adapter
power adapter, and plug the other end into a network switch
or router.
3. Plug the small end of the AC power cord into the power jack
of the adapter, and plug the large end into a wall outlet not
controlled by a switch.
Quick start guide
4. Optional: Plug the mini-USB end of the USB cable to the
Power Line
Adapter Connection box
Ethernet cable USB cable
base unit. Connect the other end of the USB cable to a PC
(to use PC speakerphone mode).
Status indicator on the wireless mic
Power up
On the cradle
Off the cradle
During
registration
Wall outlet
3
VCS 754
LAN
AC power cord
Slots
1
2
DC power cable Ethernet cable
Network switch
or router
• Orange for about two seconds.
• Orange when charging in the cradle except
during registration.
• Flash red and green alternately when the
non-registered wireless mic is charging on
the cradle.
• Green during a call.
• Red when the system is muted during a call.
• Off when the wireless mic is in idle mode or
without a battery.
• Flashes orange when the wireless mic's battery
is low.
• Flashes green when there is an incoming call.
• Flashes red slowly when the wireless mic is:
• out of range; or
• not registered; or
• off cradle during paging (with a paging tone).
• Flashes red and green alternately.