VTech EricStation VCS752 Quick Start Manual

ErisStation
®
TM
SIP Conference Phone with Two Wireless Mics Wireless Conference System
Quick Start Guide
businessphones.vtech.com
Model: VCS752
Introduction
• The ErisStation SIP Conference Phone with Two Wireless
To Adapter
Mics requires a network connection to an IP PBX to operate.
This quick start guide assumes that your network infrastructure
is established and that your IP PBX phone service has been
VCS 752
LAN
ordered and configured for your location. For more information
about installation options and phone setup, see the VCS752
Slots
User's Manual and the VCS752 Administrator and Provisioning
businessphones.vtech.com
Manual, available at
• The AC power cord is intended for a vertical or floor mount
position. The prongs are not designed to hold the plug in place if it
1
is plugged into a ceiling or cabinet outlet.
DC power cable
To power the VCS752 using PoE:
(with yellow plugs) Ethernet cable
1. Plug one end of the Ethernet cable into the Ethernet port on
the bottom of the unit.
Slots
Network switch
or router
Ethernet cable
2. Plug the other end of the cable into your network router
or switch. When the base unit is powered up, the status
indicators turn green for about two seconds.
• You can connect the VCS752 to both PoE and AC power.
Ensure that you connect the cables in the order shown in the first
diagram under "Connect base unit." Once connected, the unit will
use PoE. If PoE fails, the unit will use AC power as a backup.
Battery X2
To Adapter
Introduction
This quick start guide provides you with the basic installation,
setup, and operation instructions. A limited set of features are
described in abbreviated form.
You may refer to the user's manual for complete installation and
Slots
operation instructions for this innovative and feature-rich VTech
product.
The ErisStation SIP Conference Phone with Two Wireless Mics
is designed for use in office settings. It consists of a base unit
and two wireless mics, enabling clear conversation between
participants in different areas of a meeting room.
The VCS752 also has Bluetooth and DECT connectivity. After
pairing Bluetooth devices with the VCS752, you can use the
conference phone to make and answer cellular calls, or use a
Bluetooth headset for a private conversation.
For large meeting rooms, you can extend the range of the
VCS752 with up to three VTech VCS850 DECT expansion
speakerphones.
For more information on using the VCS752 Bluetooth and
DECT features, see the VCS752 User's Manual, available at
businessphones.vtech.com.
Slots
ErisStation is a registered trademark of VTech Communications, Inc.
®
Orbitlink Wireless Technology TM is a trademark of VTech Communications, Inc.
Wall outlet
Install the wireless mic battery
3
1. Plug the battery connector securely into the socket inside
the battery compartment. Insert the battery (with the label
THIS SIDE UP facing up) into the battery compartment.
AC power cord
.
2. Slide the battery door until it clicks into place.
Adapter
2
Network switch
or router
3. Place the wireless mics into the charging cradles until they
are flush.
The status indicator on the wireless mic turns orange when charging,
and turns off when the wireless mic is fully charged.
Parts checklist
Your VCS752 SIP Conference Phone with Two Wireless Mics
VC S7 52
package contains the following items. Save your sales receipt and
LA N
original packaging in the event warranty service is necessary.
Adapter
1 SIP Conference Phone with Two Wireless Mics
Quick Start Guide
b u s i n e s s p h o n e s .v t e c h . c o m
2
Model: VCS752
DC power cable
(with yellow plugs) Ethernet cable Quick start guide
Battery ×2
Li-ion Polymer batteries.
(x4) (x4)
(x4) (x4)
Quick start guide
AC power cord Phone line cord
To purchase any accessories or replacements, visit our website at
businessphones.vtech.com or call 1-888-370-2006.
Network switch
or router
Status indicators overview
Ethernet cable
Status indicators on the base unit
2
Battery X2
LED 1
Power up • Green for about two seconds.
On a call • Green during a call.
• Red when a call is muted.
Incoming call • Flashes green when there is an incoming call.
LED 2 (CELL 1) and 3 (CELL 2/HEADSET) (Blue)
Bluetooth device connected
Incoming call on Bluetooth device
Held call on Bluetooth device
Base is in discoverable mode
Connect base unit
The VCS752 can be powered by AC power or Power over
3
Ethernet (PoE—Class 0).
When using AC power, connect the base unit as shown below.
AC power cord
ErisStation
Network switch
Base unit or router Wireless mic ×2
1. Plug one end of the DC power cable into the power jack of
the base unit, and plug the other end into the VCS752 jack
of the power adapter. Route the cord through the slots.
Battery door ×2 Power adapter
Plug one end of the Ethernet cable into the LAN jack of the
2.
power adapter, and plug the other end into a network switch
or router.
3. Plug the small end of the AC power cord into the power jack
of the adapter, and plug the large end into a wall outlet not
controlled by a switch.
Quick start guide
• The supplied power adapter is designed for use with only the
Power Line
DC power cable connector cable Adapter Connection box Ethernet cable
ErisStation SIP Conference Phone with Two Wireless Mics. It is
not designed to power other network devices. Do not connect the
supplied power adapter to any other network devices through the
supplied DC power cable or any other Cat5e ethernet cable.
Status indicator on the wireless mic
1
3
Power up
On the cradle
ErisStation
Off the cradle
• Steady
• Flashing
• Slow flashing
• Alternating CELL 1/CELL 2
During
registration
Wall outlet
To Adapter
3
VCS 752
LAN
Slots
AC power cord
Adapter
1
2
DC power cable Network switch
(with yellow plugs) Ethernet cable or router
Slots
Network switch
or router
Ethernet cable
Battery X2
• Orange for about two seconds.
• Orange when charging in the cradle except
during registration.
• Flash red and green alternately when the
non-registered wireless mic is charging on
the cradle.
• Green during a call.
• Red when the system is muted during a call.
• Off when the wireless mic is in idle mode or
without a battery.
• Flashes orange when the wireless mic's battery
is low.
• Flashes green when there is an incoming call.
• Flashes red slowly when the wireless mic is:
• out of range; or
• not registered; or
• off cradle during paging (with a paging tone).
• Flashes red and green alternately.