Crestron DMPS3-4K-150-C Do Manual

DO GUIDE
DMPS3-4K-150-C
3-Series 4K DigitalMedia Presentation System 150
® TM
DO

Install the Device

The DMPS3-4K-150-C can be mounted into a rack, mounted under a table,
or placed onto a fl at surface.
Mounting into a Rack
The DMPS3-4K-150-C occupies 1U of rack space. Using a #1 or #2 Phillips
screwdriver, attach the two included rack ears to the device. Then, mount
the device into the rack using four mounting screws (not included).
Mounting under a Table
Using a #1 or #2 Phillips screwdriver, attach the four included table mount
brackets to the device. Then, attach the four table mount brackets to the
underside of the table using four mounting screws (not included).
Placing onto a Flat Surface
When placing the device onto a fl at surface or stacking it with other
equipment, attach the included feet near the corners on the underside of
the device.
DO

Make Connections to the Rear Panel

Make connections to the rear panel of the DMPS3-4K-150-C as follows:
VGA IN 1–4: Connect to RGB (VGA), component, S-video, or composite
video sources.
AUDIO IN 1–4: Connect to unbalanced audio sources.
HDMI IN 1–4: Connect to HDMI audio/video sources.
®
DM IN 1–2: Connect to the DM 8G+™ output of DigitalMedia™
transmitters or other DigitalMedia devices or to third-party HDBaseT
devices.
1
HDMI OUT: Connect to the display.
DM OUT: Connect to the DM 8G+ input of a DigitalMedia receiver or other
DigitalMedia device or to a third-party HDBaseT device.
1
RELAY 1–2: Connect to controllable devices.
INPUT: Connect to a digital or analog output device.
AUDIO OUT: Connect to the receiving device using the supplied 5-pin
interface connector.
IR OUT: Connect to the included Crestron STIRP IR emitter probe.
®
MIC IN: Connect to a microphone.
COM: Connect to the device to be controlled using the included 5-pin
interface connector.
LAN: Connect to the local area network.
USB 1–4 (Type A): Connect to the USB port of TT-100 Series presentation
interfaces.
G: Connect to earth ground (building steel).
NET: Connect to the 4-pin NET port of a Cresnet device using the
®
included 4-pin interface connector.
100–240V~1.4A 50/60 Hz: Connect to a 120 V power outlet using the
included power cord.
DO

Check the Box

QUANTITY PRODUCT
2 Bracket, Rack Ear, 1U
4 Bracket, Under Table Mount
2 Connector, 3-Pin
2 Connector, 4-Pin
2 Connector, 5-Pin
1 Emitter Probe, IR, Crestron STIRP
4 Foot, 0.5" x 0.5" x 0.23", Adhesive
1 Power Cord, 6' 7" (2 m)
Not Included: Cables, Rack Mount Screws, and Table Mount Screws
®
COMPUTER
LAPTOP
LAPTOP
PROJECTION
TT-100
SCREEN
SET UP
IO
AUD
RGB
IN
HDM I
HID
USB
C
X - 2 0 1 - N T E R
D M - T E R C E
M P U T
C O
D M RES ET MICROPHONE
PWR
VDC 24 0.75 A
I OUT
HDM
DM-TX-201-C
DM OUT
LAN
2
AMPLIFIER
TT-100
MONITOR
TT-100
STEREO
SPEAKERS
DM-RMC-4K-100-C
DM IN
RES ET
0-C
I OUT -10 ER UP
HDM MC -R RO LL SET
DM NT
OM CO
RO
GND DM
TX COM V
RX 24 A MAX
RTS 0.75
CTS
S 1
G IR
S 2
S
LAN
PROJECTOR
PART NUMBER
2032122
2041951
2003575
2003576
2003577
2001137
2002389
2001134
LAN
3
4