Table of Contents
Advertisement
Use
Warning! Let the tool work at its own pace. Do not overload.
Variable speed control
The variable speed control allows you to adapt the speed of
the tool to the workpiece material.
Set the control knob (3) to the desired setting. Use a high
N
speed for wood, medium speed for veneer and synthetics
and low speed for acrylic glass, non-ferrous metals and
for removing paints.
Switching on and off
To switch the tool on, press the on/off switch (1).
N
For continuous operation, press the lock-on button (2) and
N
release the on/off switch.
To switch the tool off, release the on/off switch.
N
To switch the tool off when in continuous operation,
press the on/off switch once more and release it.
Emptying the dust cassette (fig. E & G)
The dust cassette should be emptied every 10 minutes of use.
Remove the dust cassette (12) to the rear and off the tool.
N
Remove the cover (14) by twisting it clockwise.
N
Hold dust cassette with the filter (15) facing down and
N
shake the cassette to empty the contents. Shake the
cover to empty the contents.
Refit the cover (14) onto the dust cassette, twisting it
N
counterclockwise until it locks into place.
Refit the dust cassette onto the tool.
N
Cleaning the dust cassette filter
The dust cassette filter is re-usable and should be cleaned
regularly.
Empty the dust cassette (12) as described above.
N
Pull the filter (15) off the dust cassette.
N
Warning! Do not twist the filter.
Shake off excess dust by tapping the filter into a dustbin.
N
Warning! Do not brush or use compressed air or sharp
objects to clean the filter. Do not wash the filter.
Replace the filter.
N
Refit the cover.
N
Refit the dust cassette onto the tool.
N
Hints for optimum use
Always hold the tool with both hands.
N
Do not exert too much pressure on the tool.
N
Regularly check the condition of the sanding belt.
N
Replace when necessary.
Always sand with the grain of the wood.
N
When sanding new layers of paint before applying
N
another layer, use extra fine grit.
6
On very uneven surfaces, or when removing layers of
N
paint, start with a coarse grit. On other surfaces, start
with a medium grit. In both cases, gradually change to a
fine grit for a smooth finish.
Consult your retailer for more information on available
N
accessories.
Maintenance
Your tool has been designed to operate over a long period of
time with a minimum of maintenance. Continuous satisfactory
operation depends upon proper tool care and regular cleaning.
Regularly clean the ventilation slots in your tool using
N
a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth.
N
Do not use any abrasive or solvent-based cleaner.
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:
Safely dispose of the old plug.
N
Connect the brown lead to the live terminal in the new plug.
N
Connect the blue lead to the neutral terminal.
N
Warning! No connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good quality
plugs. Recommended fuse: 5 A.
Protecting the environment
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your Black & Decker product
needs replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product
available for separate collection.
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand for
raw materials.
Local regulations may provide for separate collection of
electrical products from the household, at municipal waste
sites or by the retailer when you purchase a new product.
Black & Decker provides a facility for the collection and
recycling of Black & Decker products once they have reached
the end of their working life. To take advantage of this service
please return your product to any authorised repair agent who
will collect them on our behalf.
Advertisement
Table of Contents
