Maintenance; Protecting The Environment - Black & Decker Bmt300Ka Manual

Fitting a sanding sheet (fig. D)
Line up the sanding sheet (9) with the sanding base (4) as
u
shown.
Press the sheet firmly and evenly onto the sanding base,
u
making sure that the holes in the sheet coincide with the
holes in the base.
Removing a sanding sheet
Pull the sanding sheet off the sanding base (4).
u
Warning! Never use the sanding base without a sanding
sheet or accessory in place.
Fitting alternative accessories (fig. E)
Place the spacer (5) onto the collar (10).
u
Place the alternative accessory (11) onto the collar (10).
u
Firmly attach the fixing bolt (6) into place to ensure a tight
u
fit for the alternative accessory (11).
Note: The spacer and fixing bolt are not used to attach Black
& Decker accessories. Black and decker accessories are
attached using the Super-lokTM Tool free accessory clamping
lever.
Use
Warning! Let the tool work at its own pace. Do not overload.
Warning! Before cutting into walls, floors or ceilings, check for
the location of wiring and pipes.
Variable speed control (fig. F)
The variable speed control allows you to adapt the speed of
the tool to the application.
Set the variable speed dial (2) to the desired setting. At
u
setting 1 the tool will operate at low speed, 10,000 min-1.
At setting 6 the tool will operate at the maximum speed,
22,000 min-1.
Switching on and off (fig. G)
The variable speed control allows you to adapt the speed of
the tool to the application.
To switch the tool on, slide the on/off switch (1) forward
u
(position I).
To switch the tool off, slide the on/off switch (1) to the rear
u
(position O).
Hints for optimum use
Always hold the tool securely. For precision work, hold the
u
tool near the front.
Clamp the workpiece whenever possible, especially when
u
using cutting blades.
Do not exert too much pressure on the tool.
u
Always use the appropriate type of attachment for the
u
workpiece material and type of cut.
(Original instructions)
Regularly check the condition of accessories. Replace
u
when necessary.
Mark the desired starting point.
u
Switch the tool on and slowly feed attachments into the
u
workpiece at the desired starting point.
Clamp a piece of plywood or soft wood to the back of the
u
workpiece and saw through the combination in order to
obtain a clear cut.
Do not force the cutting blade into the workpiece. Note
u
that cutting sheet metal will normally take more time than
sawing thicker wooden workpieces.
When cutting metal spread a thin film of oil along the
u
cutting line before cutting.
When sanding new layers of paint before applying another
u
layer, use extra fine grit.
On very uneven surfaces, or when removing layers of
u
paint, start with a coarse grit. On other surfaces, start with
a medium grit. In both cases, gradually change to a fine
grit for a smooth finish.
Consult your retailer for more information on available
u
accessories.

Maintenance

Your Black & Decker corded/cordless appliance/tool has been
designed to operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation depends
upon proper tool care and regular cleaning.
Warning! Before performing any maintenance on corded/
cordless power tools:
Switch off and unplug the appliance/tool.
u
Or switch off and remove the battery from the appliance/
u
tool if the appliance/tool has a separate battery pack.
Or run the battery down completely if it is integral and then
u
switch off.
Regularly clean the ventilation slots in your appliance/tool/
u
charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth. Do
u
not use any abrasive or solvent-based cleaner.

Protecting the environment

Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your Black & Decker product
needs replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product avail-
able for separate collection.
ENGLISH
7