Operation - ADJ SUPER SPOT LED User Instructions

Super Spot LED
Operating Modes:
The Super Spot LED can operate in three dif-
ferent modes. In each mode you can run the fixture as a stand alone
fixture or in a master/slave confiugration. This next section will detail
the differences in the operating modes.
Universal DMX Control:
versal DMX-512 controller to control the dimmer and strobe. A DMX
controller allows you to create unique programs tailored to your indi-
vidual needs.
1. The Super Spot LED is a 2 channel DMX fixture. See page 15 for
detailed description of the DMX values and traits.
2. To control your fixture in DMX mode, follow the set-up procedures
on pages 6-8 as well as the set-up specifications that are includ-
ed with your DMX controller.
3. Use the controller's faders to control the various DMX fixture traits.
4. This will allow you to create your own programs.
5. Follow the instructions on page 10 to set the DMX address.
6. For longer cable runs (more than a 100 feet) use a terminator on
the last fixture.
7. For help operating in DMX mode consult the manual included
with your DMX controller.
Sound Active Mode:
This mode allows either single unit or several
units linked together, to run to the beat of the music.
1. Press the MENU button until "SOUN" is displayed, and press
ENTER. Press the UP or DOWN buttons so that "ON" is dis-
played and press ENTER.
2. To adjust the sound sensitivity level press the MENU button until
"SENS" is displayed, and press ENTER. Use the UP or DOWN
buttons to adjust the sensitivity level, "0" being least sensitive,
"100" being the most sensitive. Press ENTER to set your level.
Show Mode:
In this mode you can activate the built-in program. See
pages 10-11 for more information.
1. Press the MENU button until "SHND" is displayed, and press
ENTER.
2. Press the UP or DOWN buttons to find your desired show,
press ENTER, then press and hold the MENU button for at least 3
seconds to activate.
ADJ Products, LLC - www.adj.com - Super Spot LED Instruction Manual Page 14

Operation

This function allows you to use a uni-
Super Spot LED
Master-Slave Configuration:
to 16 units together and operate without a controller. The units will be
sound activated. In a Master-Slave set-up, one unit will act as the con-
trolling unit and the others will react to the controlling units programs.
Any unit can act as a Master or as a Slave.
1. Using approved DMX data cables, daisy chain your units togeth-
er via the XLR connector on the rear of the units. Remember the
Male XLR connector is the input and the Female XLR connector
is the output. The first unit in the chain (master) will use the female
XLR connector only - The last unit in the chain will use the male
XLR connector only. For longer cable runs we suggest a termina-
tor at the last fixture.
2. For the Master, press the MENU button until "SLND" is dis-
played, and press ENTER. Set the Master unit to "MAST". Then
set the Master to your desired operating mode.
3. For the slave units press the MENU button until "SLND" is dis-
played, and press ENTER. Set the slave units to either "SL 1" or
"SL 2".
4. The slave units will now follow the Master unit.
Super Spot LED
Channel Value
1
0 - 255
2
0 - 7
8 - 15
16 - 131
132 - 139
140 - 181
182 - 189
190 - 231
232 - 239
240 - 247
248 - 255
ADJ Products, LLC - www.adj.com - Super Spot LED Instruction Manual Page 15
Master-Slave Configuration
This function will allow you to link up
1 DMX Channel Mode
Function
MASTER DIMMER
0% - 100%
STROBE
LED OFF
LED ON
STROBING SLOW - FAST
LED ON
FAST CLOSE - SLOW OPEN
LED ON
FAST OPEN - SLOW CLOSE
LED ON
RANDOM STROBE
LED ON