Table 2-3 Connector To Sensor Channel Mapping; Table 2-4 Sensor Connectors: Channel And Pin Assignments - Macurco DVP-120 Installation & Operating Instructions Manual

Each 8-terminal sensor modular connector may be disconnected from the PCB connector to ease wire
installation. The terminals will accept wire from 16 to 28 AWG. To install a wire, strip back approximately 0.25
in. (6 mm) of insulation, and insert the bare wire into the terminal. Tighten the screw clamp and ensure that the
wire cannot be easily pulled from the connector. Table 2-3 lists the connector to sensor channel correspondence.
While Table 2-4 lists channel signals, connector and terminal assignments for all 12 input channels.
Signal Name
CH 1 +24 Vdc
CH 1 +I loop
CH 1 -I loop
CH 1 24Vdc Ret
CH 2 +24 Vdc
CH 2 +I loop
CH 2 -I loop
CH 2 24Vdc Ret
CH 3 +24 Vdc
CH 3 +I loop
CH 3 -I loop
CH 3 24Vdc Ret
CH 4 +24 Vdc
CH 4 +I loop
CH 4 -I loop
CH 4 24Vdc Ret
Revision 0.07
Control Board Connector
J7
J10
J13
J8
J11
J14

Table 2-3 Connector to Sensor Channel Mapping

Connector Signal Name
-Pin
Number
J7-5 CH 5 +24 Vdc
J7-6 CH 5 +I loop
J7-7 CH 5 -I loop
J7-8 CH 5 24Vdc Ret
J7-1 CH 6 +24 Vdc
J7-2 CH 6 +I loop
J7-3 CH 6 -I loop
J7-4 CH 6 24Vdc Ret
J10-5 CH 7 +24 Vdc
J10-6 CH 7 +I loop
J10-7 CH 7 -I loop
J10-8 CH 7 24Vdc Ret
J10-1 CH 8 +24 Vdc
J10-2 CH 8 +I loop
J10-3 CH 8 -I loop
J10-4 CH 8 24Vdc Ret

Table 2-4 Sensor Connectors: Channel and Pin Assignments

Sensor Channels
1, 2
3, 4
5, 6
7, 8
9, 10
11, 12
Connector Signal Name
-Pin
Number
J13-5 CH 9 +24 Vdc
J13-6 CH 9 +I loop
J13-7 CH 9 -I loop
J13-8 CH 9 24Vdc Ret
J13-1 CH 10 +24 Vdc
J13-2 CH 10 +I loop
J13-3 CH 10 -I loop
J13-4 CH 10 24Vdc Ret
J8-5 CH 11 +24 Vdc
J8-6 CH 11 +I loop
J8-7 CH 11 -I loop
J8-8 CH 11 24Vdc Ret
J8-1 CH 12 +24 Vdc
J8-2 CH 12 +I loop
J8-3 CH 12 -I loop
J8-4 CH 12 24Vdc Ret
Connector
-Pin
Number
J11-5
J11-6
J11-7
J11-8
J11-1
J11-2
J11-3
J11-4
J14-5
J14-6
J14-7
J14-8
J14-1
J14-2
J14-3
J14-4
11