Vermont Castings 2040 Installation And Operating Manual page 26

Encore FlexBurn 2040 Non-Catalytic / Catalytic Wood Burning Stove
® ®
is a glowing ember bed 2-3" (51-75 mm) deep. (Fig. 38)
A good ember bed is necessary for proper functioning of
the non-catalytic system and may take an hour or more
to establish.
Fig. 38 Add larger pieces of wood as the fire begins to burn
well.
5. Close the damper when the griddle temperature reaches
450°F (230°C).
ST264
6. Adjust the air control for your desired heat output.
good fire
NOTE: Stove installations vary widely, and the operating
guidance given here is only a starting point . The draft man-
12/99
agement information on Page 26 will explain in detail how
the features of your installation may help or hinder good
draft, and how you may need to vary your firing technique
if your installation doesn't encourage a good draft.
Refuel While the Embers Are Still Hot
When reloading, best results will be achieved if you first
de-ash the stove by stirring the fuel bed to allow ash to fall
through the grate into the ash pan.
Do not break the charcoal into very small pieces or pound
or compress the charcoal bed.
It is important that air can circulate through the charcoal
bed during the burn. Larger pieces of charcoal allow more
air to circulate under the wood, resulting in the fire reviving
more quickly. (Fig. 39)
Fig. 39 Add full size logs after the ember bed is 3" (75mm)
deep.
26
ST264a
add wood fire
For best results when refueling, wear long-cuffed stove
gloves to protect your hands and forearms, add fuel while
the stove still has plenty of glowing embers to re-kindle the
fire, and include some smaller pieces of wood in the new
fuel load to help the stove regain its operating tempera-
ture quickly. Use this sequence as a guide to successful
refueling:
1. Open the damper.
2. De-ash the stove as described above. Open the ash-
door and check the level of ash in the ash pan. Empty
the pan if necessary and replace it in the stove. Close
the ash door.
3. Open the griddle, load the wood (smaller pieces first),
and close the griddle.
4. Close the damper.
5. When the surface temperature reaches 450°F. (230°C),
ST264
adjust the air control for the amount of heat you desire.
NOTE: If the remaining charcoal bed is relatively thick
(2-3"/51-75 mm) and if your fuel is well seasoned, it is
possible to add fresh fuel (smaller pieces first), close the
door and damper, and reset the primary air control for the
desired heat output within five minutes.
WARNING: FIREPLACE STOVES EQUIPPED WITH
DOORS SHOULD BE OPERATED ONLY WITH DOORS
FULLY OPEN OR DOORS FULLY CLOSED. IF DOORS
ARE LEFT PARTLY OPEN, GAS AND FLAME MAY BE
DRAWN OUT OF THE FIREPLACE STOVE OPENING
CREATING RISKS FROM BOTH FIRE AND SMOKE.
CAUTION: The Encore
Keep children, clothing and furniture away. Contact
may cause skin burns.
DO NOT OVERFIRE THIS HEATER. Over-firing may cause
a house fire, or can result in permanent damage to the
stove. If any part of the Encore
Routine ash removal is important for ease of maintenance,
and is important for the stove's durability. Remove ash before
it reaches the top of the ash pan. Check the level at least
once a day. Every few days, clear any ash from the outer
edges of the firebox. Most of the ash will fall through the
grate. Slice or stir the ash with a shovel or poker so that
it falls through the grate slots.
IMPORTANT: Check the level of ash in the ash pan before
reloading the stove. If the ash level is close to the top edge
of the pan, empty the pan according to this procedure:
•
Open the damper.
•
Open the griddle or front doors, and use a shovel or
ST264a
poker to stir excess ash through the ash slots in the
grate down into the ash pan.
will be hot while in operation.
®
glows, you are over-firing.
®
Ash Disposal
30005295