Switching On/Off The Microphone; Settings Via The Menu; Basic Settings - JTS UF-10TH/12 Instruction Manual

4.2 Switching on/off the microphone

1) Switch on the microphone with the button
The backlight of the display (4) lights up for a
few seconds. When you press a button (1, 3, 5),
the backlight is switched on again.
2) The display shows the following information:
the name of the unit, (10 characters), any name
may be selected (e. g. UF-10TH as shown in
fig. 1)
G = the group number (1 ...12)
C = the channel number (1 ... 60)
MHz = the receiving frequency
(624.000 ... 693.975 MHz)
. . dB = the microphone sensitivity adjusted
(-18 dB ... 12 dB)
the battery status:
full
3) To identify different microphones, remove the
cap (7) and replace it by one of the colour ID
caps supplied with the microphone.
4) To switch off, keep the button
2 seconds until the display shows

4.3 Settings via the menu

All settings are made via a menu:
1) To call up the main menu (fig. 3), keep the but-
ton SET (5) pressed for two seconds until the
menu appears on the display (4).
2) Press the button ▼ or ▲ (3) to select the
desired menu. Then call up the menu item with
the button SET.
3) To make the setting, press the button ▼ or ▲.
4) If several setup functions are available for a
menu item (e. g. group number and channel
number), press the button SET to go from one
function to the next one.
5) To save a setting, press the button SET. The dis-
play briefly shows
menu reappears.
To exit a menu item without a change, also
press the button SET. The display briefly shows
Cancel before the main menu reappears.
6) To exit the main menu, press the button ▼ or ▲
to select the menu item
button SET.
All setting options via the menu can be found in the
following chapters.
12
discharged
pressed for
Power OFF
Saving...
before the main
Exit
. Then press the

4.4 Basic settings

(1).
1) If it is difficult to read the display (4), call up the
contrast setting via the menu item
a) Keep the button SET (5) pressed for two
seconds until the main menu (fig. 3) ap -
pears.
b) Press the button ▼ or ▲ to select the menu
item Contrast
Contrast
0
c) Press the button ▼ or ▲ to set the contrast.
The display shows the value adjusted (be -
tween -3 and 3).
d) Press the button SET to save the setting.
The main menu reappears.
e) To deactivate the main menu, press the but-
ton ▼ or ▲ to select the menu item
and press the button SET or to change
another setting, select the corresponding
menu item and press the button SET.
2) Set the time for the display backlight via the
Light T
menu item
.
Light Time
15 Sec.
Always OFF
5 - 30 Sec.
Always ON
Hint: To save the batteries, it is not advisable to use
Always ON as a final setting.
3) Via the menu item
entered (10 characters max.) which will appear
on the display (e. g.
fig. 1). When several microphones are used,
this will make it easier to distinguish between
the microphones and to identify them. After the
menu item
character position is selected:
User Name
UF-10TH
Char:1/10
Press the button ▼ or ▲ to select the desired
character. Press the button SET to go to the next
character position. After setting the name, press
the button SET repeatedly until the display
shows Saving...
. Then press the button SET.
Fig. 4
:
Fig. 5
= no backlight
= time in seconds
= backlight always on
Name
, a unit name can be
UF-10TH
Name has been called up, the first
Fig. 6
. The main menu reappears.
Contrast
:
Exit
as shown in